dji phantom 4 tablet holder 3d models
840458 3d models found related to dji phantom 4 tablet holder.thingiverse
This is a very accurate extension piece to allow for the pilot of a DJI Phantom 2, 3 and 4 to mount an iPad Pro 10.5 inch or 12.9 inch screen in a secure way to the RC unit.
thingiverse
This is a very accurate "light" version of the extension piece to allow for the pilot of a DJI Phantom 2, 3 and 4 to mount an iPad Pro 10.5 inch or 12.9 inch screen in a secure way to the RC unit: https://www.thingiverse.com/thing:2814574. ... These...
thingiverse
This is an tablet holder that works on the existing DJI phone holders. It's designed around an 7 inch tablet but I am sure the designconcept will work on other sizes as well. Have you printed my design? ...I would love to hear your opinion!
prusaprinters
This is an tablet holder that works on the existing DJI phone holders. It's designed around an 7 inch tablet but I am sure the designconcept will work on other sizes as well. Have you printed my design? ...I would love to hear your opinion! Print...
thingiverse
This will allow you to use larger tablets than an iPad or an iPad without taking the case off. ...Print Settings Printer Brand: Prusa Printer:...
thingiverse
used the bracket made by markloane to make an adjustable tablet holder for my phantom controller. ...uses rubber springs on the back to keep tension on the tablet.
thingiverse
The bottom clamp use the same 4 nuts to make it stationary, while the top clamp uses two wing nuts just on the top to tighten the clamp against the tablet. They do not need to be cranked down! Rods are available at Home Depot in 12 inch lengths, as...
thingiverse
Took @DJMixtrix TK102 GPS holder and stretched the arms out enough to use the receiver on the Phantom 4 landing supports. ...Print Settings Printer Brand: MakerBot ...
thingiverse
LED holder for my P4P and Flytron Standalone Cree Leds.
thingiverse
Some dimensions were modified to handle small tablets and big phones. Holes were opened to allow faster printing and less drill bit cleanup. You need to print two clamps and one slider. The rods are #8-32, as well as the nuts. Using washers...
prusaprinters
A box to store the filters for your DJI Phantom 4. To connect the lid and the base you need a thin electronic wire. Category: Camera
3docean
This is high detailed 3d model of DJI Phantom 4 Pro - this 3d model detailed enough for close-up renders - hi-poly model - .e3d files included for Element 3D plugin (V.2.2 or higher) - big size texures included (2048×2048 pixels) - UVWs mapping with...
3docean
DJI Phantom 4 3D model ready to render complete with scene setup Polycount(with maximum smoothness): 451369 Vertexcount: 324211 Highly detailed model of the DJI Phantom4 quadcopter. The model is highpoly (most complex parts still have modifiers like...
3docean
Great Hight Detailed 3d model of DJI Phantom 4 PRO. Origionally created with 3ds Max 2014 SPECS There are 5 layers. This model contains separate 46 objects This model contains 157 474 polygons witn TurboSmooth OFF This model contains 400...
thingiverse
A battery holder for the wall to hold youre dji phantom batteries This has not been test printed
thingiverse
It's a iPad 2 3 4 holder for Phantom Dji Standard. ...And it already has support Just print in 0.3, and cut out all the support
pinshape
SummaryIt's a iPad 2 3 4 holder for Phantom Dji Standard. ...And it already has support Just print in 0.3, and cut out all the support
thingiverse
Tablet holder extender to enable the use of Tablets larger than 10" with your DJI Inspire/Phantom controller. Design features a 0.5mm recess to take 12mm foam tape to protect your tablet. ... (Pictured with iPad Air 3 10.5")
cults3d
Tablet holder extender to enable the use of Tablets larger than 10" with your DJI Inspire/Phantom controller. Design features a 0.5mm recess to take 12mm foam tape to protect your tablet. ... (Pictured with iPad Air 3 10.5")
thingiverse
made this bracket to fit my ipad mini which is in a lifeproof case too fit on the Dji phantom hand set. ... https://youtu.be/M6zYJAGwwIY
thingiverse
* It includes a mount for the "DJI Phantom 2 Part 6" internal power connector, which has the battery power and CAN data pins. * It is designed to print nicely with no supports if you print it in the right orientation (refer to pictures). *...
thingiverse
you need also this tripod-Adapter: https://www.back-bone.ca/product/bbinsta-tri/ Mit diesem Halter kannst Du die insta one r auf Deiner Phantom 4 befestigen und Videos mit Blick nach oben machen. Du kannst das Bild innerhalb der W-Lan reichweite auf...
thingiverse
This is a DJI Phantom 4 Camera Bridge. ... This can be used to mount a camera on the bootom of your DJI Phantom 4.