drok buck converter 3d models
74379 3d models found related to drok buck converter.thingiverse
Case designed to fit a Drok buck converter since I couldn't find the one I needed. The 2 pin input voltage connector is opened up in the box and so is the USB output port. ... I'm using this with a raspberry pi and my Ender 3 to make life easier while...
thingiverse
This is a basic mount for the Drok Buck converter model number 200217
thingiverse
Case for DROK 5A Buck Converter 6V-32V to 1.5-32V and 3A Adjustable Step Down Module DC 4-32V to 1.25-30V Bundle, https://www.amazon.com/DROK-Converter-1-5-32V-Adjustable-1-25-30V/dp/B08F9WSLJR. ... Being used to power my Raspberry Pi directly from my...
thingiverse
This is a case for a 12v to 5v@6A buck converter by Drok: "Buck Converter 12v to 5v, DROK 5A USB Voltage Regulator DC 9V-36V Step Down to DC 5V-5.3V 5.2V 3.5-6A Volt Transformer Power Supply Module for Phone Fast Charging" Input voltage may range...
thingiverse
This is a box for the DROK Buck Converter 24v to 5V USB that can be found here: https://www.amazon.com/dp/B01NALDSJ0?psc=1&ref=ppx_yo2_dt_b_product_details I saw the ones here in Thingiverse but none of them would fit that model. So I made a remix of...
prusaprinters
<p>These function the same as stock.</p> <p>I printed them solid in PETG, but I imagine they'd be fine out of any material including flex.</p> Category: Electronics
cults3d
These function the same as stock. ... I printed them solid in PETG, but I imagine they'd be fine out of any material including flex.
thingiverse
These function the same as stock. ... I printed them solid in PETG, but I imagine they'd be fine out of any material including flex.
grabcad
Just a quick, but accurate sketch of the casing for the familiar DROK Automatic buck boost regulator.
thingiverse
Holder for a buck convertor for my Monoprice Maker Ultimate. ...Modified https://www.thingiverse.com/thing:4627393 to take two M3 bolts and reduce plastic usage.
prusaprinters
<p>Using this as a PSU for my OctoPi (using 24V from the einsy and stepping that down to 5V)</p>
thingiverse
Wall box for DROK USB buck converters. 5V QC 3.0 Charging Module (4 ct) 6-32v input output at USB QC 3.0 levels. Mounting screw holes and a wire loom opening in bottom of case. These arrive as 4 units scored so the individual units can be...
thingiverse
With the original version, I found the supports for the lid were in the way when trying to get the converter into the enclosure, but I was able to get it in with some forcing. Unfortunately I then found that there wasn't room for me to get it in when...
thingiverse
A project box for DROK DC to DC Step Down Power Supply Module (https://smile.amazon.com/dp/B08LPVWX74?psc=1&ref=ppx_yo2ov_dt_b_product_details) with a snap on lid. The lid does not need supports. Supports are recommend for the box because of the...
thingiverse
This is a remix of the DROK buck converter. I made the inside deeper to because the ones i got have long solder pins on the bottom of the board. I also made the hole a rectangle since i think its just to see the power light. I added mounting tabs...
thingiverse
I use the Drok 090638 Buck Boost converter with automotive diagnostic tools to ensure the tool always gets 12v even during battery sags or alternator spikes. I made this enclosure to keep the board safe. The "pins" are a little fidgety to install,...
thingiverse
This bracket mounts a DROK LM2596 DC-DC buck converter onto a TDK-Lambda LS50-24 AC-DC power supply in order to make a simple benchtop power supply. Not intended for high drain use. ... The DROK PCB can be mounted using its included hardware (3/16" hex...
thingiverse
This is a case for a 24v to 12v DROK LM2596 Buck Converter. Its meant to be put on after you have adjusted the voltage as there is no way to get to the controls once its put on. It does provide a view port into the screen. ... I think there are...
cults3d
This is a case for a 24v to 12v DROK LM2596 Buck Converter. Its meant to be put on after you have adjusted the voltage as there is no way to get to the controls once its put on. It does provide a view port into the screen. ... I think there are better...
thingiverse
CASE FOR DROK 18048 DC TO DC BUCK CONVERTER STEP DOWN VOLTAGE BOARD HAS SLOTS FOR CABLE TIE STRAIN RELIEF. REQUIRES QTY 2 M3X20 HEX HEAD BOLT AND QTY 2 M3 HEX NUTS (NOT SQUARE NUTS) HEX NUTS SLIDE IN POCKETS AND ARE CAPTURED. ENJOY! ... I printed...
thingiverse
I remixed this great design but changed it for the Noctua NF-A8 FLX, Premium Quiet Fan, 3-Pin 80mm and DROK® LM2596 Analog Control Buck Converter DC-DC Step-down Transformer Voltage Regulator Module 36V 24V 12V to 5V 2A Power Inverter Volt Stabilizer...
thingiverse
There are many Buck Converter enclosures posted here, and none would fit what I thought was a common 1-button LED Buck Converter (66mm x35mm), which I bought on amazon. So I made my own. I wanted an extremely low profile design, that shows-off...
prusaprinters
There are many Buck Converter enclosures posted here, and none would fit what I thought was a common 1-button LED Buck Converter (66mm x35mm), which I bought on amazon. (<a...
prusaprinters
A case for DROK Buck Power Converter. Uses 3mm screws to mount. ...Cover has mounting for 40mm fan. https://www.amazon.com/Converter-DROK-Adjustable-Regulator-Voltmeter/dp/B00Q48BRFO?ref_=ast_sto_dp Category: Electronics
thingiverse
A case for DROK Buck Power Converter. Uses 3mm screws to mount. Cover has mounting for 40mm fan. ... https://www.amazon.com/Converter-DROK-Adjustable-Regulator-Voltmeter/dp/B00Q48BRFO?ref_=ast_sto_dp
thingiverse
... for screws for mounting on my future enclosure. https://www.amazon.com/DROK-Adjustable-Converter-Regulator-Transformer/dp/B07N3QT628/ref=mp_s_a_1_17?dchild=1&keywords=drok+buck+converter&qid=1584648971&sr=8-17&swrs=A05CE4DED55B156EC4B54C4E546E0B8E
thingiverse
This snap-together enclosure was designed to fit a Drok USB buck converter for powering a raspberry pi from the 24v power supply of an Ender 3 V2. It is designed to use foam tape or VHB tape to attach the circuit board, so it could really be used...