dromida 3d models
29 3d models found related to dromida.thingiverse
3d printable replacement Spur Gear (with 45 teeth) for the Dromida db4.18
thingiverse
The dromida servo mount options suck. The best thing I had found prior to having a 3d printer was to cut up the stock receiver/esc box and keep the bits that the servo attached to. But that option, while giving decent area to mount a servo, was...
thingiverse
Battery holder Spare part for Dromida Kodo, suitable for Revell camera quadrocopter SPOT. You can attach larger batteries to the drone with a rubber band. ...
thingiverse
For added structure use with my Dromida servo mount and it will brace it even more. Can survive impact at 50mph as tested accidentally. Currently still in updating and testing mode so if you need one check back in and i will probably have a...
thingiverse
The prop guards that come with the KODO Dromida quadcopter don't seem to be very sturdy. Or maybe I drive the thing like a drunken unicyclist. Either way, I ended up breaking one during a flight and needed to replace it. After all, it's better to...
thingiverse
hobbico dromida futaba s3114 servo mount to fit a futaba s3114 servo in the dromida 1:18 4wd sc truck
thingiverse
Pied de drone pour dromida kodo ( Revell Spot ) Print Settings Printer: Dagoma Discovery 200 Rafts: Doesn't Matter Supports: Doesn't Matter
thingiverse
I made these body posts to mount a Dromida Wasteland Truck body to a LaTrax Prerunner chassis. ...It would probably work on other LaTrax ground vehicles because I believe they share the same chassis.
thingiverse
Wall mount for Dromida Ominus, this model is identical to the Revell Rayvore. The model has to holes to mount the suport in the wall, i suggest only using the upper one, because with the screw in the lower one the remote is to tight in the socket. ... ...
thingiverse
Printed this for my Dromida 1/18 scale RC. It uses 2 10x22mm bearings commonly used in skateboard wheels. I also used three 1cm dia. magnets from Hobbyking that magnetize to the flushmount screws underneath the chassis. ... http://youtu.be/KHOsvxaycUA
cults3d
I made these body posts to mount a Dromida Wasteland Truck body to a LaTrax Prerunner chassis. It would probably work on other LaTrax ground vehicles because I believe they share the same chassis. ... See it in action:...
myminifactory
Wall mount for Dromida Ominus, this model is identical to the Revell Rayvore, to store the drone, the remote and 2 bateries and charger. For some reason I'm not able to give the right orientation to the STL file, if you want to print without...
thingiverse
This a little hook designed to be used with the Dromida Ominous FPV. Print Settings Rafts: Doesn't Matter Supports: ...
thingiverse
This motor mount will fit any 1:18 Dromida. I printed it for my db418 buggy and it runs good paired with a brushless 5400kv motor. Over the period of a week the pla melted down to slightly angle the motor so i would print two or three, however i was...
thingiverse
This is a stand I designed for my Dromida Kodo HD. The drone is put on the stand by sliding it onto the stand through the battery holder. There are also slots for the battery and controller. It has supports so that the stand is balanced when taking...
thingiverse
The latrax rally cars have a very limited amount of options when it comes to wheels. ...I wanted to use dromida rally wheels, so I needed a 7mm hex.
thingiverse
Simple slide on prop guards to help protect the softer shafts as well as the couch, or TV.
thingiverse
It's not the most beautiful wheels to drift, but it works very well. ... Layer : 0.2 mm Infill : 15%
thingiverse
Good luck finding the aluminum ones nowadays. ...Here's a decent replacement if you print from PetG or ABS.
prusaprinters
<p>A partial replacement (designed for temporary use as a spare). This hinge pin holder lets you keep driving while you wait on an order. ...It could be modified or strengthened, but I just needed a quick fix for the kids to keep driving!</p> <h3>Print...
thingiverse
A partial replacement (designed for temporary use as a spare). This hinge pin holder lets you keep driving while you wait on an order. ...It could be modified or strengthened, but I just needed a quick fix for the kids to keep driving!
thingiverse
When upgrading my MT4.18 to brushless I needed a way to mount the servo once I gutted the stock ESC/Rx combo.I got the idea from this one: https://www.thingiverse.com/thing:3235778 but it was designed for the stock servo and I wanted to upgrade to a...
thingiverse
I originally ordered some 1/18th scale Teton tires for my Helion Animus and it uses a tiny 7mm hex. ...So i designed this hex adapter. Now I'm using it with my Dromida DT4.18.
thingiverse
6 gram drone frame i made for my dromida verso. printed at like .2 layer height and 60mm/s per second speed. 100% infill obviously. .8 shell thickness do whatever you want. Printed on an anet a8. 200C nozzle and like 50C bed.This thing was made...
thingiverse
This is a cover for the drive shaft on the Dromida series SCT. It sits in place over the drive shaft to keep dirt out of the rear diff. I have printed several of these and they are in use by me and my racing buddies. I printed them standing up in...
thingiverse
- The fan will accommodate brushed or brushless motors - I used a Dromida brushed motor. Brushless would be faster but the electronics are larger/more complex. - The rocker switch in the back of the car enables power to the system. The...