durafly micro tundra fat float wheel set by 3d models

simple print with supports

Skis set for Durafly Micro Tundra Work with floats landing gear wire

This is a replacement for the float mount for the Durafly Tundra. It uses captured nuts glued into the part, and M3 machine screws instead of those silly self-tapping ones the Tundra comes with. You will need to remove foam in a few areas from...

These are wheels nuts for the Durafly Tundra. ...I modelled these from scratch and purposely made them larger than the originals to provide more support to the wheel.

Wheel Chocks for the Durafly Tundra, to keep it from rolling around in the car while driving to the field. Remixed from sebWW2 by completely redrawing his .stl in Solidworks and adding round corners & fillets to reduce the amount of fillament. And I...

Durafly Tundra (V2) wheel chocks for easy transport. These stop the plane from rolling around on the bench in the workshop or in the car during the trip to the field. Compared to others these minimise print material and grip the wheel and stay with...

Designed this as a replacement for lost wheel nut.

The factory motor for the Durafly Micro Tundra is undersized and overheats, so here's a mount for a better one. This mount allows you to replace the stock 1106-2350KV motor with the ZOHD Drift FPV Glider 87mm 1406-2600KV motor. ... You'll need the...

I had a hard landing while on floats with my Tundra. The plastic mounts separated from the foam floats and one cracked, while another sank to the bottom of the lake. I've modeled a replacement based off the original. Measured with calipers and...

Bonnet for Durafly Tundra (The little one)

Hanging hook for Durafly Tundra so you can hang up your plane on the ceiling. ... This mount will fit with Durafly Tundra universal wing mount: https://www.thingiverse.com/thing:4357646 Hanging hook are mounted by 2pcs M3x10 countersunk screws.

Mounting for GoPro to Durafly Tundra universal wing mount: https://www.thingiverse.com/thing:4357646 GoPro mount are mounted by 2pcs M3x10 countersunk screws. ...

Print @ 210° nozzle / 60 Bed Edit: Use V2 with big Lipo like 500mah

This is a basic pod suitable for holding a pan tilt camera unit on the Durafly Tundra.

Simple Transport Aid for the Durafly Tundra. Keeps it from rolling through your trunk. ... Should be loose fit.

FPV deck for Durafly Tundra V2 and DJI airunit. Camera mount is made for Savox SH-0263MG servos. I printed this using polycarbonate, because it needs to withstand the heat of the airunit. ...PETG would work also.

Motor mount to be able to put another type of engine on the durafly tundra. ... The engine mount immediately has an extra spacer for placing 3632 size brushles engines

magnetic spinner for durafly tundra. ... spinner works with stock 12x6 prop held in place by single neodymium magnet measuring 13mm od x 6.3mm id x 3mm thick the stock lock nut is steel so this grabs it really well tested multiple flights and never let...

Mount for durafly tundra bombay slot to add a camera i used some straps to mount a small hd camera. ... result: https://youtube.com/shorts/RfguNfJ4sSo?feature=share Requires 2 M4 Screws with at 15 mm ( i recommend 20mm) or 2/3 inch

A battery tray designed to hold a standard 2200mah pack in the cavernous body of the Durafly Tundra. You need to print the tray, glue it together, fit a pack and then figure out where to put the tray to get the right CoG. The design is printed in...

A quick remix so I can mount my Action cam into my Tundra using generic GoPro mount

Print Settings Printer Brand: Zortrax Printer: Zortrax M200 Rafts: Doesn't Matter Supports: No Resolution: .09 Infill: Medium Notes: I used Zortrax Ultra-T filament. Just print as fine and accurate as you can to ensure you get a nice fit. ... How I...

motor mount for stock tundra includes thrust angles...its a bit thicker than the factory part but if your plane needs this im guessing its as smashed as mine and therefore the foam can now be formed with glue lol print 100 fill with support touching...

The servo controls push rod to release a rubber band holding anything on the bottom of the Tundra. ... Needed to make it work: 1x 12g servo - I used a TowerPro MG90S 1x small zip tie to hold the servo wires in place 1x M3 screw to hold the rubber...

... functions as the propshaft. if you have excessive runout, try another cap screw or a higher quality one, as that made it better for me. oddly enough, if you use a longer screw (30mm+, you can use a spinner, which the stock tundra won't let you!

keeps battery from sliding, retained by clip and or velco strap print in 2 pieces and super glue together. you may need to heat the clip tab to bend in in to fit your battery better. print the clip side on its side so that its strongest and wont...

I've printed a set and they look like they will work fine. Flight testing yet to come. You will likely need some support for the side spacer to print correctly. I'm considering rendering the spacer as a separate part so that this can be printed...

Wheel 26 - 4

... I discovered by accident that WD40 dissolves all the glue that HK used on this. I had to do 2-3 applications of WD40 for this part to come out without much damage. Please check out my other things for the tail wheel mount and rear float mount.

This is the remix to remix :) I really liked both, original and remixed tail struts for Durafly Tundra from Hobbyking but, both Was to big for me ;) so i decided to slim it a bit ... about 1-2g, maybe not worth it but still, it looks nice. I have...