e flite apprentice s 15e mods 3d models

This thing covers the inner vertical stabilizer fin slots for the E-flite Opterra 2M when flying with only the outer stabilizers. They are secured by the carbon spar as the original fins. My prototypes on the pics above are in black but print yours...

This is a USB Nosecone mount for a friends E-Flite T-28 Trojan 1.1m RC Airplane. It will fit any USB Camera, shown in image is the USB Camera that comes with the Estes Astrocam Rocket. As far as i know it is not sold individually but as long as it...

STEP files for the E-flite EFLG330 Tricycle 25-46 landing gear set. This covers the regular 90-degree main gear set as well. These are dimensionally accurate on the exterior dimensions, mounting holes, wire locations, pivot points, etc. The interior...

STEP files for the E-flite EFLG330 Tricycle 25-46 landing gear set. This covers the regular 90-degree main gear set as well. These are dimensionally accurate on the exterior dimensions, mounting holes, wire locations, pivot points, etc. The interior...

This is my 3rd version of landing gear for the E-flite Opterra. Version 1 and 2 used double sided tape to attach to the unmodified keel of the plane. On a semi-hard landing I managed to break the plastic keel instead of having the tape come loose....

This is my 3rd version of landing gear for the E-flite Opterra. Version 1 and 2 used double sided tape to attach to the unmodified keel of the plane. On a semi-hard landing I managed to break the plastic keel instead of having the tape come...

Included files - characters with separate base - characters merged with the base - nsfw version - merged base version with supports

Air intake scoop for the AT-6 Texan 1.5m by E-FliteIf you want to support my contributions here, please consider leaving a tip https://www.paypal.com/paypalme/ShowmethedenaroNov 26, 2023Created G19 1500mm with several updates. Its a bit taller and it...

The receiver hatch fell off of my A-10 due to a bad glue job of the magnet on the fuselage, so I made a replacement. ... There are two versions one for a round 8mm x 2mm magnet, it's what I had laying around and one for the OEM bar magnet (NOT TESTED)

It's compatible with standard Timber and Turbo Timber models as well. The mount features a convenient slot at the bottom for attaching a strap, allowing users to securely fasten their camera in place. Additionally, it has space to hold TBS Jelloguard...

This is a replacement motor mount for the HobbyZone Apprentice S 2 1.2m RC plane. It is not an exact match for the original part due to some changes I made to strengthen it and make it print better, but it fits perfectly, and seems plenty strong...

This is a replacement motor mount for the HobbyZone Apprentice S 2 1.2m RC plane. It is not an exact match for the original part due to some changes I made to strengthen it and make it print better, but it fits perfectly, and seems plenty strong...

This is the double knife scabbard from the book series ranger's apprentice. Recently I have become obsessed with the books. When I looked on here, I was fairly disappointed that there wasn't anything that represented the double knife scabbard, or...

This is based on the hyperbolic pencil stand, http://www.thingiverse.com/thing:8433 The design holds mechanical components, including pre-made STLs for 23mm, 24mm and 26mm mod diameters as well as some drip tips around the mod. You can modify it with...

Direct replacement that uses the original magnet assembly. The profile is slightly more radiused which I think is more pleasing in appearance. The original had nearly straight sides, top, and bottom. PDF detail drawing included. ... STEP and Inventor...

I'm working on a project to fit two 5500 mAh LiPos under my Opterra. The goal is to significantly boost its duration and range. To achieve this, I've designed a system that involves cutting two small holes in the underside of the Opterra. This...

Retract base

Rc Micro helicopter. ... Soft: Cinema4D

Timber frames are often used to construct the rear landing gear of aircraft.

Made up some hangers for the Draco wings for storage. ...These have a small dust shelf for the connectors.

Just my design of a Insta360 Go camera mount for the Diatone TinaWhoop. ...Super Simple.

This is my set of modded parts to make it compatible with Prusa MK3(s) extruders or the many community modded extruders. Print instructionsFor more details about this build and mods please read my build thread in the V1 forums. Currently only the Y...

First mod posted is a remix of cyul's new Y endstop v2 version. I made the clamping area thicker for cleaner prints and added 2mm to each end, increasing the surface area and reducing the likelihood of the Y clamps breaking when overtightened. ...The...

I made some modifications to lilykill1's Fallout T60 helmet, available through his Patreon at https://www.patreon.com/lilykill. I added a small tab on the lower left part of the rebreather, a washer for the helmet's knob, and the head lamp. I'm...

This nozzle was initially designed for the Revell 1/144 F-15E kit but with some minor modifications it should fit other kits as well. No supports are needed for printing. Just place the nozzle vertically and chop of the nozzle at the notch after...

Humans enable the mounting of high-performance motors like the 2205, 2826, and 2212 series, which feature standardized 16x19 motor mounts for seamless integration.

Customized version of http://www.thingiverse.com/thing:188275 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=188275 Instructions Using the following options: Font_Cut = 1 Knurl_Depth = 1.5 Knurl_Width = 3...

There's nothing I enjoy more than switching the landing gear into tricycle configuration and taking off and landing over and over again, it's a thrill like no other. The pulseski.stl model I'm using has super thin skis that are incredibly flexible -...

(R©S) FHG.1B_E.S.E