e3 sentry 3d models

The USB on my CR10s Pro v2 mainboard died and since replacements are like hens teeth I opted to replace with the BTT SKR Mini E3 V3. This required an adapter in order to mount it in place so that the SD card and USB lined up on the original holes in...

This is my attempt to make case for BigTreeTech TFT35 e3 v3.0 display. There are accessible SD card slot, USB port, EXT1 & EXT2 ports and TFT port. Reset button works pefekt. UPDATE : Front_v1 no screen edges any more and the encoder hole a bit...

Using my Fusion 360 refresh of the Hero Me Base, I have created a fresh version of the Teaching Techs remix of the original Hero Me Base, but this time using the Gen2d design, for use with the DD E3 Direct Drive mount from Basaraba Innovations. Big...

This is my take on a more robust TFT35 E3 screen. I was impressed with the Elegant Mount by 3DEddy, but I wanted something even sturdier. Designed to attach to the front extrusion on either the left or right side of the bed, this mount requires two...

I wanted to raise my Presonus Eris E3.5 a bit, since I have two different heights on my desk and want to have them on the same position. Can be also used to bring them a bit higher.I use Dynavox Spikes on my Presonus and I have thin 15mm EVA Antislip...

This is an enclosure I made for upgrading my Ender 5 Plus with a BTT board (mount inside the Ender's enclosure) so I can use the TFT35 E3 V3 display as well as a Raspberry Pi with its own HDMI display. I have blocked off one of the USB sockets on...

This is an assembly of gamble604's SKR Pro v1.2 and TFT35 E3 v3.0 case ( https://www.thingiverse.com/thing:4678675 ) I put together in Fusion 360 because I wanted to see how it fit together and also prepare to integrate a couple modifications for my...

This is an assembly of gamble604's SKR Pro v1.2 and TFT35 E3 v3.0 case ( https://www.thingiverse.com/thing:4678675 ) I put together in Fusion 360 because I wanted to see how it fit together and also prepare to integrate a couple modifications for my...

Lattice frame to mount a BTT SKR Mini E3 V2 controller in the Wanhao i3 Plus. No need to rewire everything to the hot-end, You can continue to use the stock ribbon cable. All that is needed is to buy a second ribbon cable breakout board and use that...

Humans made an error, and they correct it

I made a new mainboard enclosure that fits the Ender 3 mainboard mounting pattern.I designed it around the Bigtreetech SKR Mini E3 V2.0 mainboard as that is the board I wanted to fit to my N32 Aquila. I assume other versions of the Aquila use the...

I wanted to fit my ender 3 pro with the bigtreetech Manta e3 ez board. They placed a case on their github to be able to fit the board. After hours of printing i found out that the cable connectors where extremely tight against the printerframe. I...

It was lacking some openings for the various connectors on the display. I have just imported the original model and added configurable options for -Wifi -SWD -Extra-connectors: Power, PS-On, Fil-Det, UART3 and UART4 -EXP1 and 2 In the examples, the...

I upgraded my Printrbot Simple Metal with Bigtreetech's SKR Mini E3 1.2 board, a significant upgrade that required some creative problem-solving. To mount the new board to the underside of my Printrbot, I fabricated an adapter plate that provides a...

The SKR Mini E3 is compatible, and it probably works with MKS Gen L using a board adapter (adapter not included; tested compatibility unknown). Print requires supports for front and back holes (check photos of finished print). Mounting holes can be...

During upgrade of AM8, I found that there are not that much board case made for SKR mini e3 in Thingiverse. So, I made my own. This case can be attached to any 4020 aluminum extrusion profiles. Due to possible layershifting issues by overheated...

This is a small electronics case for the SKR E3 mini v2 mounted on an Anet A8. !!!Needs M3 threaded inserts for mounting the case cover!!! SD card can be inserted from the top. Case includes recesses for five 2.5mm wire and 1mm thick cable ties for...

Turns out, that little E3 flag on the screen changes the entire mounting layout and I'm sometimes terrible at reading. In my case, (pun intended), this meant I had a pretty fantastic base for my mainboard while my screen was left hanging off the...

# 3D Printable Speaker Wall Mounts for PreSonus ERIS E3.5  ![Fully...

These parts are designed for the E3 with standard Ender Direct Drive addons. as opposed to the bowden tube job! The pen cap is 80mm to avoid conflict with the tray. The arm has the cutouts for the wheel bolt and also allows 20mm further to get...

I made a new mainboard enclosure that fits the Ender 3 mainboard mounting pattern.I designed it around the Bigtreetech SKR Mini E3 V2.0 mainboard as that is the board I wanted to fit to my N32 Aquila. I assume other versions of the Aquila use the...

These are parts to convert your Monoprice Mini Delta to have a Bigtreetech SKR mini E3 mainboard and TFT35 touch screen. It also contains parts to covert your printer to house lipo batteries and be completely portable. Many details below and full...

Introducing the SKR Mini E3 V3 mounting system for your CR10 S5 or similar unit! The screen mount and controller case are compatible with the CR10 V2 version I made.One of the striking pieces of the S5 is the size of its power supply. Being slightly...

The TAU Earth Caste employed light alloys in a Plasteel Light Frame to create buildings and infrastructure. ... This is an example of a TAU Light Observation Tower erected using the PLF system and TAU add-ons.

This medium tank is designed for tabletop wargames. ... This is an original model I created in SketchUp, inspired by American Mecha illustrations.

This is a highly advanced, state-of-the-art modular rocket system designed specifically for use in your most critical sci-fi tabletop applications. ...Each component is expertly crafted and 100% interchangeable to allow for unparalleled customization...

This is a static model with room for electronics, identical in size to this movable tracking model from which also contains instructions on how to make the legs: http://www.instructables.com/id/Building-a-moving-and-tracking-Portal-Turret/ I created...

Developed to dominate the arena of Flutter Bombs

DIGITAL FILE for you to use to print with your 3D printer or a 3D printing service. This is a fan model, and what you see in the preview is exactly what you get as it is a screenshot and full 360 rotation from inside my sculpting software leaving...

https://www.patreon.com/Kyoushuneko_Miniatures