e3d dual extruder

This is a spacer to add 20mm to the E3D Dual Extruder as on the Z5 the unit is 20mm shorter hence the nozzles would not reach the bed. ... The spacer has mounting holes for 3 screws to attach to the extruder heatsink and 1/8 threaded filament holes for...

This is a dual extruder holder for two E3D Hotends. It should work with any Prusa i2 printers. It's designed to be a pop in replacement for the standard x-carriage. ...Just snip your old zipties and place this on over the linear bearings.

This is made for dual E3D v6 extruders, 25.5mm apart, with the use of a single 40mm fan. 3mm screws are used to attach the fan to the duct. ... *This was tested with ABS so might be loose with other materials.

This is Probe mount for "Prusa i3 Adjustable E3D J-Head Dual Extruder" from this link:http://www.thingiverse.com/thing:694135 It screws directly to the Extruder and replicates the mounts for the fan mount. I made it for my own use, and decided to...

This model of an E3D Chimera is based on the official constructional drawing by E3D and real life measurements with a caliper. Intermediate detail.If you download and use my models in your own design, please leave me a like.Update 2019-05-27:...

Dual Extruder mount for E3D V6 Universal 1.75MM With nozzle spacing 31MM Print Settings Rafts: Doesn't Matter Supports: Yes Resolution: 0.1 Infill: 30 Notes: The STL files need to be scaled +10 times because of Autodesk Inventor makes them smaller...

It enables the mounting of two more E3d hotends for use with a Bowden cable extruder. It also adds on a spot to mount an 18mm capacitive or inductive sensor, for auto bed leveling. For information about the offsets to give your slicer/firmware,...

for 3D Printer Replacement Kit Dual E3D Extruder

This is a mount for two E3D V6 extruders for dual extrusion with a Geeetech i3X printer that previously only supported a single extruder.

This is a work in progress, dual extruder mount for Cube 3

So you finally get your dual extruder hotend. You can't wait to get printing. You rush through the instructions, until you come to a halt. Level your nozzles. They have to be spot on! If you just use your carriage on your printer, and lower it, it...

For pictures see the section "Update V1" //////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////// This is the second version of the E3D V6 Dual Extruder Compact X...

I've meshed this E3D V6 dual extruder mount out of: https://www.thingiverse.com/thing:2182924 & https://www.thingiverse.com/thing:2274499 to fit my needs. It's a dual extruder mount with one filament cooler and after mounting the two E3D V6 it's...

I made this to adapt a dual extruder on the Hypercube Evolution. I also use a 18mm capacitive sensor. I try to made this as small as possible, to keep a good autobed leveling and to keep the maximum travel distance You can still use the fan...

For those of you that use outcastrc's P3Steel - E3d V6 bowden dual extruder mount, but want to use an 18mm inductive sensor -- I have remixed the "cap" to have a sensor loop. It's symmetrical, so you can place the sensor loop on either side of the...

------** Check out the new version with dual fans!!----- https://www.thingiverse.com/thing:3190993 I've used the following parts: 2x E3D V6 Hotend...

just reduce the hole for the capacitive sensor to accept the 12mm inductive one

These are add on parts for use with the Dual E3D V6 Hot End X-Carrier designed by Omar Mandour (omarmandour) https://www.thingiverse.com/thing:4256131 Photos show prototype. Final version has stand-offs for tie-wrapping hot end wires to keep things...

I printed all in ABS with a fill of 100% Requested material: 6 nut 3mm (plus 6 if you need to fix the cable chain) 6 screw 3 mm 3 fan 40x40x10mm (two extruders and one to cool printed part) THIS IS A WORK IN PROGRESS, ACTUALLY WORK PERFECTLY ON MY...

Here I came up with a Dual Mount for E3D V6 Hotend, Suitable for almost every portal printer with common X-Axis Sled. ... for mounting use M3 Screws to install on X-Axis, and M5 screws and Nuts for Clamping the Hotends.

I have made a couple of dual extruder versions earlier for the Creality CR-10 but it's always something that can be made better. In this case I wanted to get rid of the painstaking alignment of the extruders Z height so the nozzles don't scrape in...

It uses the same E3D compatible mounting rail, and adds an option to use a bowden fed second extruder. The innovative part of this extuder is that it feeds the first extruder via a gear system, and the second with bowden. That allows very accurate...

I designed a new carriage and extruder setup for the OB1.4 printer to mount dual extruders on the X carriage. So far it looks like it works quite well. I am using geared stepper motors to drive the filament. They can be bought here:...

New version of dual extruder holder (E3D) with hole for inductive sensor (d=12mm).

Have you been wanting to upgrade to dual extrusion but run in to the problems of lose of build space, and having to convert to bowden extrusion; well the solution is here with my custom design for the E3D Chimera with Dual Titan extruders. My Design...

Mount to put dual E3d extruders on the P3steel. Choice of standard cap or servo mount with fans. ... Instructions Uses 3mm and 4mm mounting hardware.

This is a dual extruder mount for the Tronxy X5S using 2 E3D V6 extruders. It also has a back plate to beef up the wheels to try and prevent slop on the x-axis 2020 extrusion. You will need to print 6 of the spacers. I am running the...

I liked the simple design of the OB1.4 Dual E3D extruder from downeym, so I remixed it to fit on the RepRapPro Mendel carriage. It replaces the complete front nozzel mount of the carriage, so its easy to swap it with the original. I placed also two...

This is an upgrade for (almost) any printer with an E3D V6 extruder. This design is the 4th iteration after several failed attempts to get a secure fitment. This upgrade will enable more effective heat interruption above the nozzle to ensure less...

I designed this fan duct for the E3D Titan extruder and V6 hotend setup to use two 5015 blower fans. I intended to design cooling ducts that went on either side of the nozzle, but after trying this design out, I found it did a pretty good job on...