e3d v6 direct drive anet a8

**Note that this version is specifically for the original E3D v6.** Here's a full list of changes: * I flipped the orientation of the carriage to place the blower fan on the front (attached to the clamp) and the heatsink cooler on the side, allowing...

I just want to connect Daveposh's Anet A8 2017 version X cable chain with fine tune adjustment directly to the E3DV6_E3DHolder_with_Chain_V4 from Don1337's top-rated Anet A8 E3D V6 Bowden MODULAR X Carriage V4.

...this setup is awesome. Fantastic design! Print Settings Printer: Anet A8 w/ bowden setup Rafts: No</div>Supports: No Resolution: .2</div>Infill: 30% Notes: Don1337's Anet A8 Modular X Carriage http://www.thingiverse.com/thing:2193695

All instructions are for the Anet A8. This includes guides like my thing https://www.thingiverse.com/thing:2732685 built into the mount. Get the latest Skynet3D firmware from https://github.com/thijsk/Skynet3d and please update your firmware as...

This is a modified remix I created because the original design was a bit too snug for use with E3D v6 clones, so I expanded the mounting hole for the hotend. I also lengthened the bearing mounting holes since my printers X-rod was a tad too close...

This is a BL Touch mount for the E3D V6 carriage by 3Displacement (https://www.thingiverse.com/thing:3599905) NOTE: The holes are too small for M3 screws, so open them up first with a screwdriver tip and force the M3 screw down to create threads...

... correctly with everything mounted. Offset: #define NOZZLE_TO_PROBE_OFFSET { -37, 41, 0 } ---Original Credits: This is an addon for an 18mm sensor for FetteWorst's A8 direct extruder X-Carriage Original: https://www.thingiverse.com/thing:3369720

These include: Carriage variations to fit V1.0 Orbiter, clamp with part cooling fan mount (to use standard V6 heatsink fan clip), adapters to use all common bed levelling probes (fits Tronxy XY-08N and similar by default). For any specific...

See it run here: https://youtu.be/Nrn9100MQbY See my Rear Sensor Mount version here https://www.thingiverse.com/thing:2763157 All instructions are for the Anet A8. Reduced some sizes, moved some things and cleaned it up. I added some zip tie holes...

E3D V6 Original re-using current coolers and ABL sensor. ... I used this as baseline: https://www.thingiverse.com/thing:4169858

The E3d hotend fits directly into the bondtech extruder with ease. Clearance for the fan is set to the volcano hotend, requiring some alteration if you're not using that specific model. The 40mm hotend cooling fan attaches with four 3mm screws and...

**UPDATE** The current version uploaded to Thingiverse will not work with the Anet A8 Plus due to a misaligned chain attachment that blocks the filament entrance to the BMG extruder. I have an update in progress that fixes this issue and adds a...

This Tronxy sensor or Anet stock sensor can be used. ...Firmware Configuration came from TNS Firmware configuration Due to the altered sensor position the following changes have to be done in the configuration.h file (search for the capitalized string...

The fan is adjusted at a precise angle of 15 degrees, allowing for an enhanced line of sight directly towards the nozzle.

Some of the parts for the E3D Titan Aero were taken from GaryK47's design. On July 31, 2017, I added a Z-Axis limit switch mount for those not using auto level. Double 40mm fan duct and 12mm BL Touch sensor mounts were also added. The sensor is...

Remix of this cooling duct directs air straight to extruded material, improving overhang performance. Plus a little branded cable tidy mounts on this carriage. UPDATE: Also uploaded sensor mount for those who are interested - it only has one point of...

I'm utilizing this custom-built printer head on my personal printer, which I designed to produce significantly less noise than standard models. The four fans embedded within it allow for optimal airflow while also keeping the noise level in check - a...

Required screws 2x M3 x30mm for the hotend, 4x M3 x20mm for the fan and the strap.

I've made minor adjustments to the original 63mm version by adding holes and a lower 'cutaway' section that not only streamlines production but also enables the construction of the Mistral fan duct. ... To accommodate MrblueGray's request, I've...

I rewired the system to resolve a malfunctioning air conditioning unit issue and integrate a BlTouch mounting bracket. ...Although it may not be flawless, it operates effectively for my purposes.\r\n\r\nThe BLTouch calibration setting is adjusted at...

This is my updated upgrade plate, featuring the original fans and an 18mm capacitive sensor. It's based on a few other projects, but I made some critical mistakes in the previous version that needed correction. My goal was to position the sensor at...

In my adaptation of the upgrade plate, featuring the original fans and an 18mm capacitive sensor, I drew inspiration from various other projects. Unfortunately, there were errors in my previous design; I aimed to place the sensor at the lowest...

1 Anet E10 direct drive bracket original carriage screw Not very easy to install, the Anet E10 cart is not practical. ... Connect the extruder to the hotend with pneufit and ptfe or like me with hotend threaded tube Direct drive support for bmg...

The human-designed 18mm version of the E3D carriage without a cable duct for ejpsx was nowhere to be found, so I'll provide it here. ... #define X_PROBE_OFFSET_FROM_EXTRUDER 20 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10

18mm version without cable duct for ejpsx's E3D carriage was missing, so here it is. ... "#define X_PROBE_OFFSET_FROM_EXTRUDER -20" "#define Y_PROBE_OFFSET_FROM_EXTRUDER -10"

Here is the direct drive modification for Anet E10, mounted on the X axis with a structure featuring 15mm bearings on 8mm steel tracks. ... Modification link for X axis: https://www.thingiverse.com/thing:2637378

When I bought my first Bondtech geared direct drive (good quality clones run about $15US), I was like "wow" this thing fits right on top of my e3d v6 hotend (of which good clones run about $15US also). I won't need anything else. But every design...

When I bought my first Bondtech geared direct drive (good quality clones run about $15US), I was like "wow" this thing fits right on top of my e3d v6 hotend (of which good clones run about $15US also). I won't need anything else. But every design...

Required Parts: 4x Igus Drylin RJ4JP bearings - IGUS DryLin(R) RJ4JP 01-08 Bearing – Instead LM8UU – Reprap Mendel – Anet A8 A6 – High-Quality 3D Printer Linear Bearing 2x M3x25mm Bolts + Nuts for blower fan 2x M3x20mm Bolts + Nuts to hold carriage...

This is a custom Direct Drive mount tailored specifically for the Anet A2, carefully crafted by my friend JS. I urge anyone replicating this design to acknowledge its origin and give proper credit where it's due. ...Keep in mind that some minor...