easythreed x1 firmware 3d models

The original pi4 case now snaps into place without needing any glue, and I've attached the mounting arm from the X1 case version to it. The optional component has yet to be printed or edited, so that part is not snap-fit in place. ...For instructions...

This set of brackets comes from my YouTube review of the TronXY X1 3D Printer. These brackets may need to be adjusted slightly or the holes expanded a bit to fit properly. I modeled them in haste, but all the brackets I printed fit on my machine...

Stiffens the gantry of the Sidewinder X1. why 1/4" , well, because it's what I had laying around the house. 1/2" would be better probably, as 1/4" still has a bit of flex. 20% infill worked for me. You print two of the lower pieces, one for...

This is a detailed (though not immensely accurate) model of the Imperial Tie Advanced X1 - Darth Vader's Tie Fighter It is fully printable, without any nasty overhangs, bridges, etc. Also, there are alignment pegs for assembling the two halves.

This is just a block to show the printing area of the EPAX X1 printer. It's dimensions match the printing area volume of that printer as listed on the manufacturer's website. It's labelled with text on the front and the back of the block with the...

This innovative tool is designed for the Tronxy X1, making it an excellent alternative to traditional drawing tools. Unlike the expensive laser cutters on the market, this device uses a unique approach to create precise lines and detailed designs...

Some vents designed to fit the Artillery X1. Bottom should fit using the same screw holes as the stock intake fan. The side vents are exhausts, no real mounting for them to the printer using stock holes. My original plan was to fix them to the...

Alle zu druckenden Anbauteile für den dualFPC Umbau des Sidewinder X1. Diese Teile sind Bestandteil des Umbau Kits und müssen nur gedruckt werden, falls jemand ein anderes Material oder eine andere Farbe der Teile benötigt. Ich liefere diese Teile...

Overengineered fan duct for sidewinder X1 using 5015 fan. BLtouch connected per waggster mod. See youtube. After changing heatblock the original fanduct was not pointing right so I made a 2mm more to the front version.(fanduct-shorter). The arms have...

Recommend printing every piece flat down beside the "spine." It mounts directly onto the top of the sidewinder x1 in place of the original bearings on the front and the middle hole. Reference picture for understanding. 2 spoolholder one sides are...

This is a pressure fit Z brace mod for the Artillery X1 printer, printed with 100% infill using PLA+. It works well, and I achieved this result. To create this modification, you will need two 1/4" threaded rods and matching nuts. Use crazy glue to...

Die ist ein Messuhrhalter für den Sidewinder X1 V4. Mann kann ihn zum Messen einfach auf den Luefter stecken, und vor Druckbeginn wieder abziehen. Aber Vorsicht, beim Leveln erst die Position 2 anfahren und dann den Halter mit der Messuhr aufstecken,...

I've been busy upgrading and fine-tuning my wife's TronXY X1, which is actually owned by her University. While trying to enlarge the screw recesses on the stock build plate, I made a critical mistake - it shattered into pieces! I struggled to find a...

For the Sidewinder X1 (all versions should fit, but I have a V4). ... Parts: -2x 5/16-18 2ft length threaded rods -Two-sided mounting tape -8x 5/16-18 nuts -6x 5/16 washers -2x M5x25mm bolts -2x M5 nuts -4x M5x12mm bolts -4x M5 hammer/t nuts ...

I didn't enable all the features, which are relevant for the Bigtreetech TFT Firmware, because the custom firmware can't be flashed in case of the recently shipped GD32F305 chipset. I also left unsupported hardware features disabled. ##...

*** Also added frontLeft_standardX1 for original version X1 to clear access for usb and sd slot on sidewinder x1 version 4 My Z Axis gantry support. Solid as a rock, with some give of course. The table it was on (the printer) used to rock as...

This essentials kit for the TronXY X1 printer includes small parts that I needed or were necessary for upgrades, which weren't available at the time. Check out my videos for more information:...

The X1's tendency to spread out everywhere was starting to get under my skin, so I decided to take matters into my own hands. The solution had to be quick and easy to print, which is exactly what this design delivers. It may not win any beauty...

Steps: 1-Raise the X axis to the top 2-Release the timing belt 3-Place the supports to the X axis 4-Lower the X axis until it touches the supports, we will know that it has lowered enough when the z motors lose steps 5-Place the timing belt again...

Steps: 1-Raise the X axis to the top 2-Release the timing belt 3-Place the supports to the X axis 4-Lower the X axis until it touches the supports, we will know that it has lowered enough when the z motors lose steps 5-Place the timing belt again...

Supporto endstop y per Sidewinder X1, ho notato che tendenzialmente si sposta data la piccola vite M3 che lo fissa e il peso del bed, con questo supporto è sostenuto anche dietro oltre lla viti M4 ai lati e la sua originale M3 con il dado a martello,...

First Attempt to Replicate a Roughly 1:4 Model of the TronXY X1 3D Printer The goal here is to create a scaled-down replica of the popular TronXY X1 3D printer, but with a significant twist. We're aiming for a roughly 1:4 model, which means that all...

These changes, along with my software engineering background, and the fact that the firmware source code is freely available, I set about modifying the Prusa firmware to work on the Mega2560/Ramps1.4 board. I had some clues that it could be done...

The LCD perfectly replaces the original, and the board can be bolted on using this adapter: https://www.thingiverse.com/thing:1853712 If you use the firmware I have with the linked kit, your printer should essentially boot up and be ready for use. I...

Cadre électronique alimentation : Ce cadre s’adapte parfaitement avec la Tronxy X1 après une utilisation de cette base ( https://www.thingiverse.com/thing:2781184 ), je cherchais une base ou je pouvais intégrer une alimentation qui serais un peu plus...

Take care of your hardware first, then electronics, then firmware, and finally slicer settings. To get started, import the S3D profile (.fff) and use it as a custom machine option. Next, update Cura's resources folder with a good base profile,...

LerdgeX firmware update and config file with strong and stable accel./jerk settings Also suggest printing this https://www.thingiverse.com/thing:3674354 to replace the fan cover etc and reduce your hotend weight by alot... install the L bracket that...

this a custom firmware 2.5 for a ender 3 with a sensor (aliexpress) that is connected with a optocoupler (also aliexpress) link for the sensor...

Firmware, pictures, and instructions will be available soon. To slice these files: 1. Import your desired base or lid file. 2. Load a part modifier through slicing software and select the corresponding modifier. 3. Adjust the settings for the...

（If pop out”the same firmware would not update”, please continue to print the rest 2 files） 2.print the "【起迪-Max】双Z单头-UI" file 3.print the " PLUS X-plus参数10毫米.gcode" file After you print all the 3 files,the updating will be done. ... Im include also...