ebike controller cover 3d models
218157 3d models found related to ebike controller cover.thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/fYMqzk2WwTm
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/aU8Vk97ERhR
cults3d
This is a 3D printed BAC8000 controller (an ebike/electric vehicle controller) cover - designed to help keep out dirt, mud, salty water, etc. NOTE: You need to remove some plastic from at least 2 of the fins on the back of the controller (that...
cults3d
Box to place Speed Controller for Ebike from 250 to 750W and prevent it from getting wet.
thingiverse
This is an EGO battery mount that is designed to fit in the grooves of the eBike controller included in the conversion kit I bought on Amazon (AW brand). It is based on Matt Hoover's design for the OneWheel. You can see the instructions for...
thingiverse
I created this to house my controller for my ebike that I am currently building, its sized for a 1000w controller but feel free to remix it to your needs. I have put holes in it for both the lid and for the wires to come through, you will need to...
thingiverse
This is the battery & controller casing for my DIY eBike build series. ...Please note, my build plate is 400mm so you might have to cut it into segments.
thingiverse
We bought a new eBike with the Bosch Kiox System, when removing the Unit the contacts are left to rained upon. Therefore I designed this cover to place into the unit's place. Also adding a note, that motor is locked with the kiox. ... You can...
thingiverse
When traveling with my ebike on a bike rack with other bikes - I wanted to protect the LCD screen from the elements as well as damage from the other bikes on the rack - so I designed this cover to protect the screen. Its a simple design in TinkerCAD...
thingiverse
i conversed a bmc supertrail2 to ebike and the frame had very little space for battery, so i had to make this cover to get it to fit. https://ciclotek.com/gb/li-ion-battery-sets-for-ebike/30-bs-36v-128-ah-battery-set.html That battery fits inside.
thingiverse
This is a cover for the Lectric Ebike's display. It is not waterproof. I did use supports for the slot on the top and the lip on the bottom. I printed it face down. It attaches by putting the bottom lip behind the bottom of the display and...
cults3d
This is a cover for the Lectric Ebike's display. It is not waterproof. I did use supports for the slot on the top and the lip on the bottom. I printed it face down. It attaches by putting the bottom lip behind the bottom of the display and...
thingiverse
The top cover is supposed to snap into place after you screw(m4) and glue the frame mount and insert the controller. You should be able to insert 2 hose clamps into the frame mount and snug it up somewhere on your bike. Do not print with...
grabcad
I converted my old mountain bike into an ebike and wanted to build a nice and sleek housing for the motor controller.This is the bike I used: https://www.walmart.com/ip/Hyper-Bicycles-26in-Men-s-Havoc-Mountain-Bike-Black/102003163This is the ebike...
thingiverse
I converted my old mountain bike into an ebike and wanted to build a nice and sleek housing for the motor controller. This is the bike I used: https://www.walmart.com/ip/Hyper-Bicycles-26in-Men-s-Havoc-Mountain-Bike-Black/102003163 This is the ebike...
thingiverse
Bottom cover for Rattan LM/LW 750 battery. ...Use to cover bontacts while charging your battery or in storage.
thingiverse
A slip over cover to protect my display screen on my RadMini Step-Thru.
thingiverse
I Designed a cover for the battery instead of the one broken off from my bike. ... Hope it fits your battery too :)
thingiverse
These brackets can be used to attach a battery cover (KD325920021 or KD325921072) to a Focus eBike without the battery installed. This has been tested on a Focus JAM2 2020 The bottom bracket requires two small screws to keep in in place. ...The top...
thingiverse
This is a small cover for the battery connector on many Aventon Ebikes. I made this for the Pace 500, but it should work for other models. I store my bike in a garage and charge it inside, so I wanted to cover the battery connector while the battery...
prusaprinters
I made this charging port cover for my ebike because the original one broke.You can print this cover with TPU. Ideally, you print it with the bolt symbol facing down. ...If you want to avoid the overhang, there is a version without the bolt.</p><p>The...
thingiverse
I created a less rugged alternative headlight cover for this AliExpress headlight. ... https://www.aliexpress.com/item/1005004830554886.html
thingiverse
My foldable bike charger cover tore off very fast, and I finally got to modeling a replacement. ...Printed in TPU for maximal flexibility, but I'd imagine disposable units can be printed with almost anything given thinned first layer.
thingiverse
... controller box was designed for old Kona bike. ...It can be mounted for every bike frame if the rear angle is close to 88 degrees. It is visible on the photo I have attached. The area inside can provide a place for KT48 20A controller and some cables.
youmagine
3D printable charging port cover replacement for Denver Orus / Carrefour Toplife ebike. ...Working great on an Orus E4000.