effector and affector 3d models

This is a revised version of the original design, specifically tailored for magnets with 12mm in diameter. ...For detailed descriptions and printing instructions, please refer to the authentic design. ...Thank you!

Original 4010: https://www.thingiverse.com/thing:2873494 Original 3510: https://www.thingiverse.com/thing:2683671 If you prefer to print with PETG and use larger fans, check out this option: 5015 Volcano Version:...

I was in dire need of a highly precise probe and grew exhausted with unreliable sensors. This unit employs a high-standard microswitch, and functions exceptionally well. It is an updated version now designed to be more like a sport utility vehicle...

I have been printing with these carriage for a few weeks already at 150mm/s outside wall; 200mm/s inside wall and infill with no issues. Requires: - 6x 12mm M3 - 12x 16mm M3 - 3x 6mm M4 - They are used to attach the springs for the flying...

I've also added another STL file that includes a prop guard - supports are needed and cleanup is required to achieve optimal results. ... Print Settings: Printer: DaVinci Uno 1.0 Rafts: No Supports: Yes ...

Taller version of https://www.thingiverse.com/thing:4648938/files to fit the Predator Delta Mine has 440mm arms and is able to print full bed diameter put a bunch of hole in it to reduce weight also opened the center path up as it sat at the wrong...

... This change was necessary because the screws were sticking out from underneath it, and I didn't like the fact that the LED ring would collide with them and become distorted in shape. ...Adding an extra 2 mm of height should rectify this issue.

So I made this design by focusing on good cooling, and fans are not angled, so it might not be good for heating beds with clips. It requires eight 2x8mm screws. Print 2x Fan Holder Print 2x Fan Duct one of mirrored. Heatsink duct is...

Printer head delta is designed to accommodate inductive sensors and houses a 40mm fan effectively. The gap between the holes measures 60mm, tilted at a precise angle of 45 degrees. Secure the components using allen screws M6x10, complemented by a...

I'm experimenting with rearranging airflow for the hot end and two cooling fans to enhance part cooling performance. Can you provide feedback on whether this setup is an improvement over the original configuration? I appreciate any insights you can...

... misalignment, so I took matters into my own hands - literally. ...Cutting away the excess holes was a no-brainer, and adding reinforced posts ensured they stayed firmly in place. ...Print Settings: 0.20mm precision at an optimal 80% fill density.

This Is The Main Component With Advanced Design\n Rod Pitch Measured At 40mm\nFourteen Hundred And Ten Fans Installed In Triplet Configuration\nSix M3 Screws, Each Measuring Sixty Millimeters In Length, Are Used For Assembly Purposes\nSimilarly, Six...

This is a remix from https://www.thingiverse.com/thing:4646891 I had no M3 threaded rods, so I modified the design and added slots for m3 nuts/ lock nuts to use screws from the outside. ...the M3 screws need to be at least 25 mm long (original are 16mm)...

I tried several other plates on this site, and while they are excellent designs, using them would cause my arms to no longer be parallel, so rather than continue adding fixes on top of each other, I decided to create a mount similar to the stock one...

I took the original model from Thingiverse, specifically http://www.thingiverse.com/thing:841691/#comments, and added two new posts for an IR mount, a small wire harness mount/rest, as well as drilled holes for 3mm.\nIf there's interest in a 4mm...

To address this issue, I developed a method using a flexible driveshaft to mount the extruder motor to the frame and convert our hot end into a direct drive hotend. This allows flexible materials to be directly fed into the hot end while keeping the...

This is variant for a NF Crazy/Mosquito hotend and mini Sherpa extruder. For assembly, please see the photos. Project is under development, I will supplement it with updates. ... Some links: Optic sensor: ...

That's exactly what I did, and I'm glad I did. The original is indeed excellent, but this one may have its own unique charm worth exploring. ...To take it to the next level, I paired it with a FLSUN delta kossel 40mm fan upgrade that you can easily find...

Cable holder that secures directly into the standard hotend of the Anycubic delta printer, gripping heater, thermistor, and fan cables in place. ...Designed with a subtle offset to the rear for optimal cable management by moving them further away from...

This design is based on the magnetic carriage for Kossel developed by Haydn Huntley and shared on YouMagine at https://www.youmagine.com/designs/kossel-plus-magnetic-effectormodified. ...It utilizes 10mm ball bearings with m4 threads available from...

Do not use this, I had to recalibrate my Anycubic Predator and then the original from https://www.thingiverse.com/thing:4441076 is perfect for the Turmberg3D - Hotend Set , bigger hole for the heatsink is nessisary...

Mixing and matching different sized fans will not pose a challenge – merely install your chosen configuration accordingly, be it 30 mm or 40 mm sizes, as both options can coexist quite smoothly together. To reinforce connections between side units...

... required to loosen the hole slightly to push them in. all holes are left with tight tolerances and should be drilled out with exception to the holes on the arms. using any lower temp material isn't advisable. plate weight approx. 19 grams. ...

... for this model. Resolution: A resolution of 0.2 millimeters per step is used. Infill percentage: An infill percentage between fifty and seventy-five percent is specified. ...Notes: Printing with PETG plastic results in the best possible outcome.

... V6 hotend. In other literature E3D mentions the Volcano being 8.5mm taller. I went with 8.5mm. I used 2 of the 5015 fan mounts (modified for Volcano), plus 2 of the wide nozzles and the wide 40mm hotend fan mount (from the original project).

This end effector is specifically designed for the E3D Volcano hotend, and it can be easily modified to accommodate 1.75 mm or 3 mm filament by simply printing a different holder clip. The end effector base also features an 18 mm hole that's perfect...

This creation was crafted entirely within Tinkercad's digital realm. ...Embark on an edit adventure now at https://www.tinkercad.com/things/qk6xj7z2F4b.

Individuals have a height of approximately 2.78 feet between their arm bones.