eggtimer rocketry 3d models
313 3d models found related to eggtimer rocketry.thingiverse
Customized version of https://www.thingiverse.com/thing:468917 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=468917
thingiverse
I wanted a way to mount my Proton altimeter while using as little real estate as possible in my av-bay. This was made for the Turnigy 460mah nano-tech battery shown in the photo. ...I drilled and tapped for 4-40 screws to mount the altimeter to the...
thingiverse
Hand-held case for the Eggtimer Rocketry Receiver (B5 revision board), with GPS and voice modules. The LCD mount requires spaces for the LCD and the main receiver board. I have included the Open SCAD file for those wanting to modify the dimensions....
thingiverse
Eggtimer Flight Computer Set. ...For use in 3d modeling of rocketry avionics bays that include eggtimer products.
thingiverse
https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...
thingiverse
Rocketry tooling. Includes coring / divergent nozzle, convergent nozzle / ram rod, ram rod with hole, ram rod without hole. ... For schedule 40 pvc 1/2"
thingiverse
This is a model of the Eggtimer Quasar Rev G3 as measured by myself, featuring the largest components to help you fit it in tight places.
thingiverse
I wanted to make scenery timelapse videos and I edited the GoPro Holder file a little bit to hold cheap eggtimer.
thingiverse
Holder is made for a Eggtimer GPS Mini. M3 hardware is used to secure the GPS and a 12mm standoff w 2 m3 x 5 screws secures the Turnigy 180 mAh 2s Battery or equivalent (34mm x 20mm x 12mm) This mount is intended to be ziptied to the shock chord. ... ...
thingiverse
This case is for the Eggtimer Eggfinder LCD with internal GPS Module that is primarily used for retrieving/finding Rockets. This case was designed to use 18650 Li-Ion batteries which can be charged via USB C. Li-Po batteries can be used but Li-Ion...
thingiverse
Protective case for your Eggtimer Quantum so that it doesn't accidentally get damaged when it's not in a rocket. This case also fit the Eggtimer WIFI Switch. ... Edit: I have now included the fusion 360 file incase you want to make alteration to the...
thingiverse
Protective case for your Eggtimer Proton so that it doesn't accidentally get damaged when it's not in a rocket. ... Edit: I have now included the fusion 360 file, incase you want to make alteration to the design.
prusaprinters
Protective case for your Eggtimer Quantum so that it doesn't accidentally get damaged when it's not in a rocket. This case also fit the Eggtimer WIFI Switch. Edit: I have now included the fusion 360 file incase you want to make alteration to the...
thingiverse
Protective case for your Eggtimer Quark so that it doesn't accidentally get damaged when its not in a rocket. I sugest printing the 2 parts separately, that way you get a much better finish on the slot that hold the Quark and you shouldn't have...
prusaprinters
Protective case for your Eggtimer Proton so that it doesn't accidentally get damaged when it's not in a rocket. Edit: I have now included the fusion 360 file, incase you want to make alteration to the design. Print instructionsCategory: 3D Printing...
grabcad
The high power rocket design was created by DG&A Rocketry, a now defunct business. It was modeled using data from RockSim and information on the internet. ... It was converted to dual deploy and has room on the end for a engine retainer.
thingiverse
This is a simple rocketry launch controller designed to accommodate an XT30 connector as the safety switch, an Illuminated Toggle Switch with Cover (guard) from Adafruit, and an Illuminated Triangle Pushbutton also from Adafruit. This launch...
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/dVSAwv2KLj3
prusaprinters
Model made for use with Estes Model rocketry partsyou need 2 centering rings
thingiverse
The rocket is designed to allow for flow streaming through the craft and being accellerated, or even ionized during the period inside the rocket, that could bring pressurized gas to feed the propellers at higher altitudes then we can to this day with...
thingiverse
Spiral rocket fins for model rocketry. Use standard 18mm motors like C6 dor D9 motors. ... Need a 40mm cardboard tube.
prusaprinters
The design was not originally intended to be 3D printed but can be with scaling modifications of the parts. If you would like to learn more about our team and the rocket itself you should check out our website, https://rocketry.ncssm.edu/ Category:...
thingiverse
Hello, this is BRRDS, (Best Rocketry Research Determination System), a high-power rocket developed at NCSSM over the past 3 years from 2019 and launched in late 2021. The purpose of the rocket was for research but really being able to go...
cults3d
Hello, this is BRRDS, (Best Rocketry Research Determination System), a high-power rocket developed at NCSSM over the past 3 years from 2019 and launched in late 2021. The purpose of the rocket was for research but really being able to go supersonic...
myminifactory
Hello, this is BRRDS, (Best Rocketry Research Determination System), a high-power rocket developed at NCSSM over the past 3 years from 2019 and launched in late 2021. The purpose of the rocket was for research but really being able to go supersonic...
grabcad
My first revision of an experimental flight avionics board for 54mm model rocketry. Pretty tough to design though. This device consists of three PCBs stacking together. The power management board(bottom) contains a switching regulator from TI and two...