eisel frame stand 3d models

The stand is also the right way to close the frame, so that the photo frame and stand become one.Available passe-partouts:1st prizeChampionEllipseForever in our heartsmy loveKeyhole ulala (for over 18 years)RectangleI printed everything on my Prusa...

The stand is also the right way to close the frame, so that the photo frame and stand become one.Available passe-partouts:1st prizeChampionEllipseForever in our heartsmy loveKeyhole ulala (for over 18 years)RectangleI printed everything on my Prusa...

I created a stand version from my Christmas tree hanging photo frame found here.Reference: https://www.prusaprinters.org/prints/93150-instax-mini-photo-frame-tree-ornament Add the photo and place wherever you like. Print Settings:Printer:...

This stand is designed specifically for the IKEA FISKBO series photo frame, and I've personally tested it on frames measuring 10x15 cm and 13x18 cm with excellent results. ...Keep in mind that IKEA often updates their designs slightly between versions,...

 The metal plaque in the picture was then glued to the middle. For the frame, add a filament change at the layer where the design starts in order to have a two tone design without an MMU2.I used two different wood PLA colors, but anything will...

The part that attaches the stand to the frame had the little lugs snapped off, so I drew it up and printed a new one. ... It's not really related to the print, but I also had to reinforce the part of the stand where it screws on to this part with epoxy...

*adjusts monocle* The screw I used to secure the frame to the stand is a 3.8mm bolt, which came with my Anet A8 kit. I'm being completely honest here and saying this frame is somewhat flimsy. It's perfect for how you see the light positioned in the...

Galaxy Watch charging stand / puck frame.Either print the entire stand or print just the puck frame. You could even place rubber feet on the bottom of the puck holder for a unique looking charging pad that won't slide around your desk.Designed to...

Fortunately the main unit survived, but the original threaded stand broke where it screwed into the body.The original threaded rod was able to be repaired with superglue, but I decided to design and print a stronger replacement.For your convenience,...

The cap isn't necessary but provides a secure way to hold the token inside the frame in case of drop. No support needed except for the cap Printed at 0.4 layer height with a 0.6 nozzle. ...I didn't test it with a 0.4 nozzle but I think the result...

It's a simple stand for an acrylic photo frame that can be bought on aliexpress. It is designed for the 254x203mm that is 19.4mm thick. It's best printed on its side. Link to product.https://www.aliexpress.com/item/32896321582.html It is used for...

That's all your standard sizes, with centerline markings, here to help clean up your drafting bench!Note that it is easy to knock tubes off this little stand so I recommend using multiple stands per tube (not just one at each end). This was designed...

It's a simple stand for an acrylic photo frame that can be bought on aliexpress. It is designed for the 254x203mm that is 19.4mm thick.</p> <p>It's best printed on its side.</p> <p>Link to product.<br/> <a...

If you've got a sleek new Pixel 3 (non-XL version) and an older Nexus wireless charger on hand, this frame or stand will come in handy to position the Pixel perfectly over the charger. The Nexus charger fits neatly into the center, and with a 1.8-amp...

The cap isn't necessary but provides a secure way to hold the token inside the frame in case of drop.No support needed except for the capPrinted at 0.4 layer height with a 0.6 nozzle. ...I didn't test it with a 0.4 nozzle but I think the result would be...

A steel-framed structure supports an electric motor at the drum testing facility, designed to assess tire durability.

Hold upright q2ok's UDOO x86 3D printed case to enable the case to stand on its own end.

The original phone frame holder was too short for my large phone with case. It is a Note 10. Frame was extended 15mm on the thread side. The channel around where the ball screws in was flattened to remove the need for supports in that area...

This design is to place the Raspberry PI camera directly facing the print. ...You will need to have the screws and frame nuts that come with the printer in order to attached it to the rail.

The original phone frame holder was too short for my large phone with case. It is a Note 10. Frame was extended 15mm on the thread side. The channel around where the ball screws in was flattened to remove the need for supports in that area (Speeds...

Picture frame leg, standard size. Picture Support. I had the original leg break on me. This one worked flawlessly. The print quality was not excellent since I printed it with a resolution of 0.4mm. ...I suggest printing at a higher resolution, but for...

... on. ...Printed this using RAL 9016 "traffic white" PLA (Busch Jaeger claims the darker series to be close to RAL 9013 "oyster white", but very rare.) Thanks ot the guy designing the frame, I also stole this: https://www.thingiverse.com/thing:2856520

This product is a versatile pen holder that features an adjustable message board and picture frame, allowing you to personalize it according to your preferences. ...It's the perfect addition to any desk or office space for both function and style.

A small stand leg which can be attached to the plates, panes or other objects which need to be supported to standI suggest not to use the G-Code file as you should scale the model according to your needs.One can print it directly and attach with...

A heartwarming gift is a delicate, easel-styled picture holder adorned with dainty hearts and petite flowers on either side, carefully crafted for a cherished relative who treasures a small engraving on thin wood, delicately showcased by this...

... design for portraits, they are 2 recessed pieces, it is printed in approximately 2 hours. It is not convenient to use it for frames larger than 13x18cm, otherwise you will need to scale it. ...Do not forget to like it if you liked it, thank you.

Procedure to create an .svg file with your custom parameters:: 1 - Install Freecad (fFee and Open-Source) https://www.freecadweb.org 2 - Open Book_Stand_template.FCStd 3 - Change the parameters indo the Spreadsheet "Configuration Here" 4 - The model...

Procedure to create an .svg file with your custom parameters:: 1 - Install Freecad (Free and Open-Source) https://www.freecadweb.org 2 - Open Book_Stand_template.FCStd 3 - Change the parameters indo the Spreadsheet "Configuration Here" 4 - The model...

What you need: 1- Create your Lithophane picture here : https://tool.itslitho.com/CreateModel?fbclid=IwAR0KwptkrRXLSwPDUypCAV3w8k17ULX74G8Z11TKp9dzuu6ksr_4rmdf01k#/CreateModel 2- Model settings to be set to fit my stand are the following ones :...

2- Model settings to be set to fit my stand are the following ones : (Check pictures attached) a. Arc / Height : 150mm b. Angle : 50 Deg c. Min Thick : 0.8mm d. Max Thick : 3.2mm e. Thinnest Layer : 0.8mm f. Tchickness : 3mm g. Depth :...