electrical terminals and connectors 3d models
2263925 3d models found related to electrical terminals and connectors.grabcad
The model was originally made for use in a car subwoofer, although it is often used in other electronics. ...It's a spring loaded type electrical terminal for quick and easy use.
thingiverse
Simple part to connect electrical tubes from different sizes - 40 -> 25 - 40 -> 20 - 25 -> 20 Edit: Added version with triple 25 input Edit2: Added straight versions with triple 20-20 25-25 40-40 input
grabcad
A Prototyping Kit; PCBs and a Contact Assortment.This is available on Amazon for $15 and includes five PCB sizes, male & female contacts and screw terminals:KIT CONTENTS:• 8x each of 80x20mm & 70x30mm PCBs.• 5x each 70x50mm & 60x40mm...
grabcad
Screw and Tab Connectors for Printed Circuit Boardshttp://wecoconnectors.com/products/983-W
thingiverse
Cover of electrical terminals for switching power supply Mean Well e.g. ...NES-50 series.
cults3d
2 command panels and all the command/order tokens you will need (and extras that you may want anyway) Designed to work with 4mm diameter, 1mm thickness magnets, you will need 74 for the trays and 1 for each token. ... Photographed print used FDM for...
thingiverse
This is a simple part that lets you use an M5 bolt with an 8mm head and matching hardware as an electrical binding post (essentially a single post bus bar) for tying multiple ring terminals together. I needed this for use in an arcade machine but...
thingiverse
Cover for 8 Pin Way Terminals Waterproof Electrical Wire Connector Plug Can be printed with ABS or flexible PLA if you wish. Buy 5 Set connectors from here 8 core stranded wire from here Use 2x 20mm M2.5 screws with Chamfer head to fix the covers to...
grabcad
These reduced diameters allow for smaller threaded sections where an electrical screw on connector can attach to and interface with the integrated electrical pins inside the bolt body. There are several isometric views of the fastener, with and...
cults3d
This box is designed to place in it the starting pieces, termination, intermediate connectors and doors of descent second edition. ... This litlle box is designed to place in it the pieces of beginning, termination, intermediate connectors and doors of...
thingiverse
see: Fully Printable Terminal Block Electrical Connector - V2 ************************************************************************************************* Needed some terminal blocks but had to wait a week so made these. Each is set on a 7.5mm...
myminifactory
This set includes a number of different layouts for banks of computer consoles and terminals. Should be useful in any kind of future, or sci fi setting. If you like this type of stuff, I have a patreon with a huge archive of models for Tabletop...
thingiverse
This is my version 2 (and a lot better) of previous connectors for 15mm x 30mm oval aluminium tubes. ...This has better support for the aluminium and slight bigger holes for screws (version 1 tent to crack when screwing).
thingiverse
This is a sphere connector with isometrically aligned holes and rod kit for small constructions.
thingiverse
Snap together and bend up to 90 degrees. ... 5 point and 3 point connectors could be used for icosahedrons, dodecahedrons, and other shapes.
thingiverse
T and X connectors for a wooden shelf thickness of 19 mm, maybe 18 mm and 20 mm can work. ...Test it !
thingiverse
Customized version of http://www.thingiverse.com/thing:2125460 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2125460
thingiverse
Customized version of http://www.thingiverse.com/thing:2125460 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2125460
thingiverse
I started out by recreating MT30 male & female connectors which are so accurate they fit the real connectors, then used those models to create a mount which can hold either connector. The mount holes are 18mm apart for M3 bolts. Included are a...
thingiverse
Connectors (2 back to back) go into slots and connect walls and/or columns. No glue required, but the two rails may be glued back to back End pieces go into the same slots and close them for aesthetic purposes or increase footprint for stability. 4...
thingiverse
4 supports: vertical and horizontal connection tabs left and right positioned 7 connectors, straight and 90°, all of them with vertical or horizontal tab placement. i also include the smatphone holder the connector and the tomtom XL holder. all...
prusaprinters
these are some supports and connector i designed because i need some of them to replace my 12 yo tomtom with a smartphone to be used as a navigator and speed meter (very old but still functional samsung galaxy s2, maybe in the future i'll switch to...
thingiverse
Some connectors/supports for Mountaineers to help make the mountain boards more stable.
thingiverse
there are a total of 19 connecting pieces: slot nuts, corner connectors, extension plates, etc the sliding blocks are available with and without nut (M3). without nut, simply screw in the screw. for better hold and for frequent use, please use the...
thingiverse
Junction box for ABB EPJ 5-pole round terminals - smaller diameter, available eg. https://www.gme.cz/krab-venecek-6304-10. Probably available only on Czech and Slovak markets. Krabice na malý pětivěneček ABB EPJ/SEZ typu 6304. Tenhle věneček je...
thingiverse
My old cable connectors were not working any more, so I decided to replace them. What you also need is a cable 2x0,5 or something like that. You have to unisolate the end of the cables 4mm and stick them in the holes. After that you can place the...