emax tinyhawk 2 vs tinyhawk s 3d models

Arm guards for the EMAX Tinyhawk Freestyle are a great idea, especially after ripping the arms up sliding on concrete. This essential accessory acts as protection for the carbon frame, soft landing gear, and delicate mounts for the motors. To install...

Remixed the Runcam nano 2 mount to fit the Foxeer Predator 4 nano on the Tinyhawk Freestyle for a friend. The Foxeer camera is 3mm longer than the Runcam. I will add a picture of the result if my friend send me one. ...;-) 31/1/2020 Added a version 2 of...

I've attached the Hawkeye Firefly micro cam mount to my Tinyhawk Freestyle drone. To secure it properly, I fed the second half of the battery strap through the hole at the base of the mount. The mount itself is a friction fit, so I included two...

I got a tinyhawk cheap, i can not get it to bind, so i wanna put a crazybee board in it that i have here...... so here we are :) https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner...

it weight less than 2g. but like everybody, we do not like it because we can not simply install in our current drone since it use weird fittings.also Tinyhawk Frestyle is not the best frame for modification. i can see a lot of people having trouble...

Adding a Card Recording Function to the Tinyhawk II Model To install, please use the TWK01M01 20-card recording plate for 20x20 boards. For whoop-sized cards with 25x25 installation holes, use the TWK01M05 25-card recording plate. Additional...

I desperately needed a firefly mount for my tinyhawk freestyle so I went ahead and created one - it was definitely a challenge! 5,25 and 45 degree mounts, and a strap to help keep the plug out of the props were all part of the design. Flexible...

I got a tinyhawk cheap, i can not get it to bind, so i wanna put a crazybee board in it that i have here...... so here we are :) https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the...

They are incredibly easy to install and can be made in quantity to fit your preferred battery, allowing you to simply swap them into your Tinyhawk when needed. The mounts are crafted from TPU material to ensure they won't break and provide added...

I got a tinyhawk cheap, i can not get it to bind, so i wanna put a crazybee board in it that i have here...... so here we are :)</p> <p><a href="https://www.thingiverse.com/thing:4441076">https://www.thingiverse.com/thing:4441076</a> presented a...

After trying a few designs off here and finding they still caused jello, I designed my own. ... This is Zip Tied on so it wont suit everyone. NOTE: This is for the insta360 Go. Not the Go 2

I loved Kororor's design but unfortunately, my Happymodel 1s charger wouldn't fit inside. So, I tweaked it by removing some of the battery holders to make room for the charger. The result is a snug fit that might require sanding down the charger's...

... to provide extra protection against high-impact drops, especially when using the robust Runcam Nano V2. ...I've recently found a revised design that offers improved durability and peace of mind - it's available now on Thingiverse as an updated version.

Print with tree supports preferably. Print mount in upright orientation. Soft mount with double sided foam tape on the bottom (remove protective backing at personal preference, I did not remove). Top side soft mount is two spacer o-rings. Rig is...

This remix originates from thingiverse.com/thing:3858777. Notably, the legs feature a hexagonal shape. Additionally, the antenna holder is angled at 30 degrees. ...Furthermore, the XT30 support boasts an angle of 15 degrees and includes a small notch at...

Tinyhawk Freestyle Adapter for 16x16 all in one stack

Tinyhawk 3 Pinch Camera Mount with VTx pocket

I acquired several Tattu 600 1S batteries, but unfortunately, they didn't fit snugly in the stock holder. I decided to redesign it from scratch to accommodate those specific batteries perfectly. ...Version two of this project refines the design further,...

Just my design of a Insta360 Go camera mount for the Emax TinyHawkS

Hello, this is a AIO Board (Whoop Size 25x25mm) holder for the Tinyhawk 2 Freestyle Frame and a holder for a Full Size Cam (19x19mm). Happy printing and have Fun. ...;-)

Screw on front of the frame. ...Snug fit from PLA

No supports required, I printed at 0.3 layers and it looks great. ...Fits 8 450mAh BetaFPV 1S Batteries

Remixed from original design by Takumi13. I wanted a version to mount to the top of the quad (I'm not using a camera mount), so I included two cutouts to make room for the stock camera frame. ...I also modified it for a different printing orientation...

Mount for crossfire and omni antenna. ... Mirror the skid in ur slicer for securing the immortal t antenna

NOTE BEFORE PRINTING! -RUNCAM SPLIT 3 LITE ONLY (no mounting options) -Requires Longer Nylon Standoffs! (Suggested link at bottom) -TPU! This is a camera mount, Non TPU may cause Jello or Vibrations - SWAP THE PINS ON THE RUNCAMSPLIT - the...

It works great, and it is much more durable than pla or tpu. To make it print the mold, then mix type 1 silicon (the acetic one) with about 10 drops of food coloring. Next step is kind of optinal, depending of what you want the final product to...

This is a soft mount that can solve the Jello problem on the Insta360 GO. ... Take a look at the video on my YT channel: https://www.youtube.com/watch?v=GSTVzVCG4JQ&t=18s Need 2x O-rings to complete the assembly.

Print in TPU, 40% infill, no supports.

Cut it out and get a grip on that shaky camera already!

stop that sloppy camera! ... Category: R/C Vehicles