enclosure anycubic vyper 3d models

... Rig 3.5" PiTFT Touch Display" by adafruit. ...You need the top of the case too.In the bottom of the case I add 2 holes for threaded nuts, M6.The holder for the Anycubic Vyper is a new design from me.I also have a matching Pi-Camera stand for the Vyper!

top mount rail for anycubic vyper rail distance 36 mm print without support you can use my m4-fluegel to attache things on the rail but not for mounting the rail on vslot

Design is for Anycubic Vyper, version C with thick cables. <b>Total items needed:</b> 1x Heatbed 1x Support Upper 1x Support Lower 18x Link 100% 18x Link Cover 100% 18x Link 130% 18x Link Cover 130% <b>Installation:</b> Installation...

REMOVE .STL FROM FILE NAME Manually transferred CHEP's profiles for the Anycubic Vyper. This is the best quality setup to 0.4mm thickness rather 0.42mm and layer height of 0.16mm instead of 0.12mm. ... This can be reverted with slightly longer...

Inglish: Simple cigarette case for roll-your-own cigarettes with a sliding lid. It has space for approximately 13 roll-your-own cigarettes. English: Single cigarette case for roll-your-own cigarettes with sliding lid. ...It has space for approximately...

<p>While looking at <a href="https://www.thingiverse.com/thing:4966317">https://www.thingiverse.com/thing:4966317</a> I wanted to recreate the entire drawer, so that I could squeeze even more use out of the space :)</p> <p>So far this has resulted in...

Customized version of https://www.thingiverse.com/thing:34558 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=34558

Unitak3D LED Switch Bracket for Vyper

Needed a mounting mechanism for: https://www.thingiverse.com/thing:5335318 https://www.thingiverse.com/thing:3294512 or https://www.thingiverse.com/thing:3294512 on my Anycubic Vyper. I already switched out my filament sensor bracket for a 45 degree...

For the Anycubic Vyper V2 (purchased 2022-12). Size adjustment to frame slot : Wider (20mm -> 32mm) Model was remixed in Freecad. Thank you JBDoge for the original print and ChimeraTech for the remix i used. P.S. Just saw that ChimeraTech...

This is my modified version for a direct drive upgrade for an Anycubic Vyper 3D printer using a NON-STOCK Micro-Swiss Bowden Extruder. (Link: https://www.3djake.com/micro-swiss/bowden-dual-gear-extruder) I remixed this part from:...

This is just a simple Cam holder for Vyper

The Anycubic Vyper V6 mount by Glutt0ne fits great on the Vyper however it does not work with the volcano heat block because it hangs down further than the stock z stops. I designed these zstop extenders to slip over the the stock z stop pegs. The...

This allowed me to use the stock metal mount holding the sensor to attach this mount to the Z axis to track the print going up. 3M x 12-16mm screw to attach camera back housing. Print Settings Printer Brand: Anycubic Printer: All-metal Mega Rafts:...

Needed a mounting mechanism for: https://www.thingiverse.com/thing:5335318 https://www.thingiverse.com/thing:3294512 or https://www.thingiverse.com/thing:3294512 on my Anycubic Vyper. I already switched out my filament sensor bracket for a 45...

Mount for my camera on my vyper. ... Enjoy if it fits your needs

I used these for modifying my Hornets, Vypers and Venoms to be able to swap between weapon configurations using round 3 x 3 x 1mm rare earth magnet. ... Vyper : https://www.instagram.com/p/BvBaraPnXVy/ Venom : https://www.instagram.com/p/BvBYHJBnK0A/...

Finally a case for my Raspberry Pi Zero 2W with Pin Header for Anycubic Vyper

Finally a case for my Raspberry Pi Zero 2W with Pin Header for Anycubic Vyper

This is a clip on webcam mount for the Creality Ender 3 and Anycubic Vyper. The mount can be clipped on to the side and a pin can be printed for the Swivel arm. The mount is slightly tight and needs a little wiggle and it will clip into place. ...

This is a clip on webcam mount for the Creality Ender 3 and Anycubic Vyper. The mount can be clipped on to the side and a pin can be printed for the Swivel arm. The mount is slightly tight and needs a little wiggle and it will clip into place. I...

Here i make a Holder for the Vyper Upgrade to Direct Extruder with Stepper Motor to backside. ...Ideal for Extruder asRedrex Dual Gear Extruder Ender 3 or derivate.

... extruder. By doing so, the bowden connector is also closer to the printer which saves space the the sidewall of an enclosure and allows a bigger radius for the bowden tube. Feel free to use, share and modify! ...:) Feedback and comments welcome!

Vyper bed attachment for a 10x20 cable chain For the extruder part, I drilled a hole in the end piece and screwed it onto the two holes that are normally used to secure the cable with a zip-tie, but that's only worth for the first Vyper version, the...

Remix of IKEA lacquer leg extension (Vyper) by BigBalu I filled in the hole to reduce print time. It was about 30 minutes faster without the hole in the middle. Printed with 3 walls/shells at 10% infill. ...Still sturdy and strong, love the original...

Print SettingsPrinter:Anycubic VyperRafts:NoSupports:NoResolution:0.2Infill:20Filament brand:EryoneFilament color:Matt Navy BlueFilament material:PLA

... tense the sensor too much when the z goes up/down. This hopefully will prolong the life of the sensor itself. F3D file included to allow adjustments of holes if needed. Feel free to modify the design as long as you share back to Vyper community.

Vyper Class Heavy Fighter Proxy for 30k and 40k Games, Anyone? I'm betting the community could come up with some great rules to adapt this kit for use in these iconic games. If someone takes on this project, I'd love to see the results! ...Please share...

The cover is compatible with Suunto Vyper and Zoop (older version) diving computers.The visibility is pretty good, especially in water.Once I test it in a real dive I will post additional  photos. I printed it with transparent PETG on a Prusa mini...