ender 3 axis 3d models

MY TAKE ON THE ENDER 3 S1 PRO Y AXIS MOUNT. ...WIP Printing Temperature: 233˚C DON'T RUN OVER 245˚C It'll Start Smelling Like Breakfast Bed Temperature: 60˚C Printing Speed: 50 - 60mm/s Fan: ON FULL TILT ...

I had issues aligning the original part on my Ender 3 Pro. To resolve this, I tweaked it by pushing the support further away from the mounting point by 1.65mm. Additionally, I elevated the bearing holder up by 11mm to ensure it's perfectly aligned...

Ender 3 Pro Z Axis Lead Screw guard. I needed a design that would perfectly align with the bracket, so cut outs were added to the bottom for crush rings to fit snugly inside. The lead screw guard is also adjustable to accommodate any necessary...

When installing a Bondtech Extruder with included ender 3 mount, you lose the ability to hold the X-Axis cable. Bondtech item: https://www.bondtech.se/en/product/creality-cr-10-kit/ My simple design will allow you to secure your cable. You...

This is an X-Axis mount made to fit the Ender 3V2 X axis arm/tensioner. ...I used it as a way to mount a camera for taking time lapses that moved up with the Z height.

Qr code cover for the ender 3, print in a upright position for the best results

This is a remix of the Ender 3 v2 X-Axis Camera mount. I've extended the arm by almost 14.5cm and added an end piece that is 6.77cm long that you can use to better angle the camera.Best to print it laying flat with at least 3 walls. I printed 15%...

This modification gives the Y axis rail of the Ender 3 a significantly wider footprint for its rollers, resulting in superior stability and rigidity. All necessary details can be found within the accompanying PDF. Please note that although this mod...

Maybe I'm doing something wrong, but on my Ender 3 v2, the Z-axis limiter sits too high when I'm not using the glass bed. I usually loosen the bolts and slide it down a little if I need to, but there is a small plastic tab that has to be maneuvered...

Maybe I'm doing something wrong, but on my Ender 3 v2, the Z-axis limiter sits too high when I'm not using the glass bed. I usually loosen the bolts and slide it down a little if I need to, but there is a small plastic tab that has to be maneuvered...

This spacer is specifically designed for the Ender 3 Pro and has only been verified to work seamlessly with the damper shown above. To function properly, a modification of the printer is required, but this modification can all be reversed if needed....

This is a modification to the Y axis rail of the Ender 3 to provide a much wider footprint for the rollers which gives far better stability and rigidity. All the details are in the provided PDF. BEWARE! although this mod is completely reversible, a...

I was unable to find any existing designs for an enclosure for the Y-axis pulleys on the Ender 3. This is Revision Two of my design, which is still in progress. I need to make some adjustments to ensure there's enough clearance above the idler pulley...

... Bearing blocks modified from, https://www.thingiverse.com/thing:3443703 Reddit link with pictures and links for purchased items. https://www.reddit.com/r/3Dprinting/comments/lkwmyt/added_dual_z_axis_to_my_ender_3_pro_lots_of_pics/

I designed a dual Z axis mod for my Creality Ender 3, but I wanted it to look similar to the CR-10S's design. Since there was one available, I edited and borrowed files from the CR-10 OEM - Complete 3D Model, CR-10 Dual Z-Axis Belt Synchronizer, and...

So I remixed the display camera mount and the Z-Axis Handle to one modell and adjusted the screw hole size.See https://www.printables.com/de/model/172815-ender-3-s1-pi-camera-mount for the holder and screw to mount the case or print the version,...

[Ender 3 V2](https://amzn.to/2MddE5f) Y-Axis Stepper Motor Damper Mount remixed from the design by: [Ra1ns](https://www.thingiverse.com/thing:4591114) to fit my specific dampers and provide clearance for full retraction of the Y-axis. My dampers:...

This is a fairly accurate representation of the x-axis limit switch on my Ender 3 Pro. I took the STEP file from [Creality's...

Using the newest parts you will only need: x2 5mm Bore toothless GT2 Idler Pulley (one for each axis) This is the bracket I'm using to add an idler for the Y belt on the Ender 3. While the bracket is fully inserted into the aluminum extrusion, you...

Made this because the x-cover from the ender 3 v2 is slightly different from the original ender 3. I personally like cows, that is why I put one on it. I also included a cover without anything. ...Enjoy!

Ender 3 Lead Screw Stabilizer. ... I fixed it because it didn't fit on the 20x20 bare metal.

Stock Ender 3 Pro screws may be a bit too short. Also, 4 m4 nylon washers can be used for stepper motor screws, but this is optional. Tweezers may be helpful for assembly. ## Assembly procedure If you use a non-stock stepper motor with a...

When installing a Bondtech Extruder with included ender 3 mount, you lose the ability to hold the X-Axis cable.Bondtech item: https://www.bondtech.se/en/product/creality-cr-10-kit/My simple design will allow you to secure your cable.You will need to...

My Ender 3 v2 x-axis zeros on the absolute edge of the build plate leaving no margin on one side and 15mm on the other. This spacer attaches to the print head gantry plate so that the x-limit triggers earlier and the auto home zeros on a reasonable...

I've tried some different direct printing tools on my Ender 3 v2 and all of them make me loose between 0.5-1cm on the Y axis. Yesterday i was talking about this to a frend who told me a way to enlarge that distance on the Y axis in a easy way. He...

I've tried some different direct printing tools on my Ender 3 v2 and all of them make me loose between 0.5-1cm on the Y axis. Yesterday i was talking about this to a frend who told me a way to enlarge that distance on the Y axis in a easy way. He...

This part is intended to space out the z-axis motor from the metal structure on the Ender 3 Pro 3D printer. Over a long period of time, the stock spacing of the z-axis metal rod can be bent from too much pressure applied by the horizontal gantry. ...

I have designed this z axis brace for my ender 3 max. I had problems with unstable z axis problems since i bought the printer, andi tought it could be braced like on the cr10 series. The parts need to be mirrored to get it for each side. Parts you...

Slots in under the Z-stop sensor to account for a spring upgrade on the Ender 3 v2. ... Additional files included to customize for your printer.

Use this tool to adjust the length of the Z axis lead screw, which is now 3 millimeters longer than its original size.