ender 3 axis 3d models

2021 Aug 1 - decreased 1mm height of back part, seems perfect fit now.A cover for 4040 Metal Tensioner.Print SettingsPrinter Brand:Creality Printer: Ender 3Rafts:No Supports: NoResolution:0.2mm Infill: 10Filament:CaiGe PLA Marble     Category: 3D...

Pi camera with IR Ender 3S1 Mount. ...See Original design for mount example

Position the mount to facilitate the installation of the caliper for precise axis calibration.

This mount is designed to work with these stepper motor dampers from Amazon (in case it goes down, it's listed as *"CCTREE NEMA 17 Stepper Steel and Rubber Vibration Dampers with M3 Screw Upgrade for Creality Ender 3 Ender 3 pro CR-10 CR-10S 3D...

I upgraded to dual Z motors using a Comgrow CR-10 kit on my Ender 3, which necessitated a PSU mount and led me to design a simple one. This should smoothly slide into the extrusion and securely fasten to the PSU with two bolts mounted on the tallest...

I have only tried this on the  Ender 3 pro; other printers may have the holes in the correct place.To check your lead screw - move the gantry to the top (as seen in photo) and measure gap. Then measure the gap closer to the stepper motor. I had a...

It's a remix of Y tensioner for the Ender 3 Pro with 40x40 V-sot Profile. I want to thank Cornely_Cool as he generously shared step files with me. That helped me to adapt his work for wide 10mm idler pulleys. I used W10T20B5 idler pulley. It fits...

Z-Axis Stepper Motor Planetary Gear Upgrade **What this mod does:** The Z-axis stepper motor works at 1.8° steps, with a quad threaded lead screw that raises the X gantry by 8mm per revolution. 200 steps in a full circle, with 0.04mm per full step.

It performs adequately, yet I've yet to discover a comparable model. ...It functions exceptionally well, with no constraints or inconsistencies in the Z-axis movement.

After replacing my X axis Belt tensioner I decided to change my Y axis belt tensioner too, since the printer had looked half baked in my eyes :D Yet again another Quick'n Dirty remix of Cornaly_Cool's design. Thanks mate.. You will need to use the...

... back (motor side) of the Y axis assembly. ...Employs standard F688ZZ bearings sourced from the front y-axis idler (replacing with F608 provides the necessary bend radius for the belt and clearance on that end), a solitary >16mm M3 screw, and an M3 nut.

Ajustment mount for Z axis steppermotor and threaded Rod on single and dual Z axis. Mount will gain an even force in XY direction, from bottom to the top. Motor mount is ajustable in X direction, and Stepper motor in Y Direction. Top mount is...

... You need to download and print the two files including plus the endstop cover from: https://www.thingiverse.com/thing:3394736. The Z axis endstop is the same as the X and Y axis ones, you can use any of them. ... You will need 4 M3 screws.

X-axis motor cover to reposition the limit switch to -10mm. ...This is allows full use of the bed when updgrading to a spider hot end and larger fan duct.

Just my design of a cable holder mount to X-axis and 40x40 profile. For mount on the profile, I used a washer printed from PLA. You need 4 zip ties to mount cable and 4xM5 screws. ... Enjoy:)

This remix lets you lift the position of your Z-axis end stop switch, giving you the freedom to install longer nozzles, hotends, and more without needing to adjust the bed's height or re-tighten the spring tension.

I remixed Nandomeier's design so the clip is on the other side of the Z-axis guide, this way it lines up with where my cable comes out from under the printer.

I completely agree with you, CDeviant designed a piece that perfectly fits the Ender-3 Pro and it's incredibly sturdy. It just works seamlessly.\r\n\r\nWhen I installed CDeviant's design, I encountered a few issues:\r\n- The stepper motor was...

Lube the thread. # Changelog 26/03/2020: Added a beefy version, 0 backlash and 0 flex, end of Z problems. 16/05/2019: Modify to use custom backslash Print instructions4 Perimeters Backslash: 0.1 layer height 3 perimeters turn off: ensure vertical...

I used 3M heavy duty double side tape to secure the fan duct/shroud to the y-axis sensor housing (next to the stepper itself) only needs tape fan and screws to secure the fan to the duct. There are internal wind vanes to ensure proper position...

Carefully install the z-axis rod stabilizing bearing by first disengaging the coupler at the bottom of the rod. Then, gently push the bearing into position and slowly lower the rod back down. ...A friction fit should develop as you slide the bearing...

I replaced my standard stepper fan mount with a modified version from Thingiverse, specifically the one located at https://www.thingiverse.com/thing:4110189, but unfortunately, it still failed to reach the y-axis end stop. ...Therefore, I designed and...

... выровнять движение ремня. Требуется 625 подшипник. Y-axis motor support with bearing. This support eliminates shaft misalignment and reduces the load on the motor bearings, as well as allows you to align the belt movement. ...Requires 625 bearing.

This is a Y axis mount for the bed side of the Y chain made by diogosantos88 https://www.thingiverse.com/thing:3715002 and remixed by Tobi0892 https://www.thingiverse.com/thing:4316238 . I was using a chain made by johnniewhiskey...

The frame braces come from ProperPrinting, paired with a dual Z axis mod utilizing KFL08 Bearing Brackets. I chose to use the KFL08 because the 608 bearings were yielding poor results due to excessive slack and play between the bearings and the T8...

I considered creating an upgrade starting from a Z-axis guide equipped with 608Z bearings sourced from https://www.thingiverse.com/fafabienman/about . By integrating a filament guide extension, I've managed to merge the functionality of a Z bearing...

Here the rationale of the [original mount](https://www.thingiverse.com/thing:4832197): > This is a Y-axis motor mount for Ender3 Pro. The stock mount requires an idler pulley, which has direct belt-teeth - unteethed pulley contact. This can cause...

Print Settings Printer Brand: Creality Printer: CR-10 Mini Rafts: Doesn't Matter Supports: Doesn't Matter Infill: 100% How I Designed This modification to the hot end file: modified the socket to fit 10x20 chain, increased structure thickness couple...

So I made this redesign that allows the Wheels/Rollers to turn freely.Print SettingsPrinter Brand:CrealityPrinter: Ender 3Rafts:Doesn't MatterSupports: YesResolution:0.16 or 0.2Infill: 55Filament: Generic PLA PLA White Notes:The OG model can be found...

So I made this redesign that allows the Wheels/Rollers to turn freely.Print SettingsPrinter Brand:CrealityPrinter: Ender 3Rafts:Doesn't MatterSupports: YesResolution:0.16 or 0.2Infill: 55Filament: Generic PLA PLA White Notes:The OG model can be found...