ender 3 cure profile 3d models
821858 3d models found related to ender 3 cure profile.thingiverse
Ender 3 profile for adesive led strip. Light up your 3D creation. ...
thingiverse
This is a profile for the settings I use to get my ender 3 to print the best I can.
cults3d
I am sharing with you my configuration file for the Ender 3, Ender 3 Pro, and Ender 3 V2. The parameters were calculated and tested on several test cubes to get the best out of Cura. In addition, I managed to reduce the printing times by an...
thingiverse
Do you want QUICK and FAST results on your prints, Why don't you try my cura profile for the ENDER 3 AND PLA First you have to put the profile in cura, select it, and PRINT ! ... Tell me if there's things who are not working, Bye Have Good Prints !
cults3d
... ...Do you want QUICK and FAST results on your prints, Why don't you try my cura profile for the ENDER 3 AND PLA First you have to put the profile in cura, select it, and PRINT ! ... Tell me if there's things who are not working, Bye Have Good Prints !
cults3d
I present you the Ender 3 profile for Simplify 3D. It took me a long time to make it, more than 20 calibration cubes were needed to get the best speed, quality with the default profile, the best shrinkage, and the best print times with a 20% fill...
thingiverse
Print your chosen profile version ( V1,V2 or V3) twice for Ender 3 (maybe use a brim) , or adjust the length of the profile for your Printer. _____________________ V1 Print list: LED_Profile_V1 (2x) V1_Endcap_left (1x) V1_Endcap_right (1x)...
thingiverse
I had to create it myself, it's just the insert to cover the profiles to prevent them from collecting filament scrap. You can easily adjust the length to your needs in your slicer, just remember to unlock the "preserve aspect ratio"! ... Printing: ...
thingiverse
Alu profile filler to prevent debris falling into it. 141.4 mm for the front left side. 93mm for the back left side if needed. 30 mm and 41 mm is compatible with cable chain holder: https://www.thingiverse.com/thing:2920060 Here the filler...
thingiverse
My personally ender 3 profile with direct drive and dual gear
prusaprinters
best profile ive found for the ender 3 s1, takes care of stringing and much better quality
thingiverse
Hello, Try this with my ender 3 profile here : https://www.thingiverse.com/thing:3642806 Follow me on instagram : @pierreprinting Follow me on instagram : @pierreprinting Follow me on instagram : @pierreprinting LIKE LIKE LIKE FOLLOW ME BYE
cults3d
Hello, Try this with my ender 3 profile here : https://www.thingiverse.com/thing:3642806 Follow me on instagram : @pierreprinting Follow me on instagram : @pierreprinting Follow me on instagram : @pierreprinting LIKE LIKE LIKE FOLLOW ME BYE
thingiverse
Requirements: * must be using the original Ender-3 rubber feet * 2 pieces of 20x20x8mm rubber feet to attach to the end * correctly aligned y axis profile! (get rid of any skew/tilt first) * most likely incompatible with any mod on either end of the...
thingiverse
... is endcap for 40x40 profile. I moved LCD on the left side of Ender-3 to save some space on the right. Enjoy Ps. Printed with 0,8mm nozzle(more speed - less quality)! ... Printing with smaller diameter gives better quality than on the picture.
thingiverse
Ender 3 ABS profile with 220C nozzle 100C bed. Fan is set to 15%. These settings are for some older MakerBot ABS I had laying around. Settings will likely need to be tweaked for different brands/blends. Note: Thingiverse requires a 3D object...
thingiverse
This is a remix of markarsenich's Ender 3 Double Drawer. I had an issue where my Y axis bolt would smash into the top of the drawers, so I made a low profile, single drawer variation. This drawer also mounts on both the Y axis profile as well as the...
thingiverse
This is a profile of a clip slot for the aluminum rails on an ender 3 printer. Should work with most Creality printers or any printer with the basic extruded aluminum rails. This is a part to be used for attaching anything to an ender 3 printer. I...
cults3d
... I offer you the profile of the Ender 3 with BLTouch for PrusaSlicer. I spent some time to make it, it will offer you nice impressions with settings that I took the time to study. I hope you will like it, and it will work for you as it did for me.
thingiverse
Also, check out these other mods that dramatically reduce the sound of your Ender 3 * [X-Axis Stepper Damper](https://www.thingiverse.com/thing:3494744) * [Y-Axis Stepper Damper](https://www.thingiverse.com/thing:3488452) * [Z-Axis Stepper...
thingiverse
The model is a top mounted version and aimed at allowing the printer head assembly to move the full height - I have an Ender 3 V2 modified with the Micro Swiss direct drive assembly, which were restricted by the side profile mounted version of the...
thingiverse
I have taken the best information from very talented 3D printer experts and experimented for weeks until I combined multiple ideas into a perfect profile for my ender 3 pro. Prints take much longer than .2 layer hights but if you don't mind the...
prusaprinters
A quick search on Thingiverse got me to Smokey Joe's model which inspired me to create this version. The model is a top mounted version and aimed at allowing the printer head assembly to move the full height - I have an Ender 3 V2 modified with the...
prusaprinters
It's amazing how much quieter this makes things!Updates:2019-03-03 - Angled the edge of the base to match the top angle and reduce filament use.Also, check out these other mods that dramatically reduce the sound of your Ender 3X-Axis Stepper...
cults3d
cover profile T 25x25mm Visit my website: www.thinking3dthings.com
thingiverse
Nachdem ich das Mainboard vom Ender in ein neues Gehäuse auf die Geräterückseite verlagert habe fehlte eine Endkappe. Hier ist sie. Einfach und ohne Eingepresstes Logo. ... Die FreeCAD original Datei enthält eine Tabelle mit Variablen für...
thingiverse
I use Cura 3.6 Spiderman model here: https://www.thingiverse.com/thing:1692007
thingiverse
This is provided on the memory card for the Creality Ender 3 and has been included for anyone who has an Ender 3 but doesn't have this file anymore. NOTE: Since the 'test-dog.gcode' was sliced in an older version of Cura I was unable to simply...