ender 3 filament holder thingiverse 3d models
2065951 3d models found related to ender 3 filament holder thingiverse.thingiverse
Filament free stand for Ender 3 stock holder. ... You can use the original screws and washers.
prusaprinters
Filament spool holder for Ender 3 style printers.The spool holder has the Creality Ender logo on both sides.It has been hollowed out a bit to save filament and time.Original spool holder design: https://www.thingiverse.com/thing:3544593Spool holder...
thingiverse
Ender 3 Filament Holder. No screws, placed in the frame profile. Recommended filling is 30-40%. ... To mount the bobbin bracket, you need two M5 bolts 15-20mm long and two M5 nuts
thingiverse
ender 3 filament holder ,simple easy and it works , most filament holders i have seen takes hours to print so i designed a basic one that dont take that long to print but still does the job. you have got to use a bit of force getting them on there i...
thingiverse
A simple roller bearing spool holder that replaces the original Ender 3 spool holder. ...Uses the original pressure clip ring.
myminifactory
So here is my take on a filament holder for the Ender 3. Some additional non-3D printed parts are needed, in particular 4 608zz bearings and 2 axles. I used 8mm aluminum tubing, but 5/16 dowel should work too. I also have the source files on...
thingiverse
Creality Ender 3 Filiment roll holder, fits in original spool holder hole. ... didnt need any support to print ( the thread did need a slight sand and spray with wd40) but tightens up nice
thingiverse
So here is my take on a filament holder for the Ender 3. Some additional non-3D printed parts are needed, in particular 4 608zz bearings and 2 axles. I used 8mm aluminum tubing, but 5/16 dowel should work too. I also have the [source...
thingiverse
Simple & Minimal Filament Holder You will need two 608ZZ bearings. ... Remix: Curved Roller (https://www.thingiverse.com/thing:4244293) Screw & Nut (https://www.thingiverse.com/thing:3732949)
thingiverse
I use 10x15x4 mm x2 bearings holder and nut print horizontal roller print vertical 20% infill PLA BFplast Roller length 84mm Filament weight 1kg
thingiverse
If you want save some height in the Ender 3d printer that is a good solution. Also is required to used to original spool holder in the assembly. For reference in the project we have some parts not printed displayed in brown. ... Bill of Materials: ...
thingiverse
Custom filament hanger using sealed ball bearings for smooth operation. Note that this reduces height capacity of the printer for a little bit. ... Additional parts required: - 1x 120mm M8 bolt - 2x M8 nuts and washers - 4x M3x10mm bolts - 4x...
cults3d
Custom filament hanger using sealed ball bearings for smooth operation. Note that this reduces height capacity of the printer for a little bit. ... Additional parts required: - 1x 120mm M8 bolt - 2x M8 nuts and washers - 4x M3x10mm bolts - 4x hammer...
thingiverse
Fundo this amazing holder from HugoHuge, but I have some spools that are less thick than the usual and they does not fit on the original design. I remade it to be less thick but fit the rest of the parts from the original. ...
thingiverse
Holds filament spools. Print the base on its flat side. This maximizes strength, and is the reason why the upper hole is offset from center. Print the nut and bolt upright. Perhaps in a future version I will enable the bolt to be printed sideways...
thingiverse
Filament coil holder for Ender 3. ... Soporte bobina filamento para Ender 3.
cults3d
This Ender 3 Filament Extension is inserted into the original roll holder.
thingiverse
quick print, low filament usage remix for Ender 3 side spool holder.
thingiverse
This Ender 3 Filament Extension is inserted into the original roll holder.
thingiverse
Filament sensor holder for ender 3. For direct drive version. ... V2 version I moved the sensor higher.
thingiverse
Ender 3 Pro filament spool holder adapter. Remixed from and for use with... ... https://www.thingiverse.com/thing:3209211 Required a 90 degree adapter due to upgrade to 'direct drive' modification.
thingiverse
ENDER 3 PRO SETUP AND IMPROVEMENTS https://www.youtube.com/watch?v=wUEyVB6nFYo SUBSCRIBE!! ... FILAMENT SPOOL HOLDER: https://www.thingiverse.com/thing:2070272 BEARINGS/RODAMIENTOS: http://amzn.eu/d2HUwX9 THREADED ROD https://amzn.to/2Ntshi6
thingiverse
Bracket for the stock Ender 3 filament spool holder. Relocates the filament spool to the side and back. This eliminates the need for extra filament guides and leaves the full z-height accesible. ... Uses two additional M5x10 (or longer) screws and two...