ender 3 filament holder 3d models
1149231 3d models found related to ender 3 filament holder.thingiverse
Ender 3 Filament Holder. No screws, placed in the frame profile. Recommended filling is 30-40%. ... To mount the bobbin bracket, you need two M5 bolts 15-20mm long and two M5 nuts
thingiverse
ender 3 filament holder ,simple easy and it works , most filament holders i have seen takes hours to print so i designed a basic one that dont take that long to print but still does the job. you have got to use a bit of force getting them on there i...
thingiverse
Bracket for the stock Ender 3 filament spool holder. Relocates the filament spool to the side and back. This eliminates the need for extra filament guides and leaves the full z-height accesible. ... Uses two additional M5x10 (or longer) screws and two...
thingiverse
Filament free stand for Ender 3 stock holder. ... You can use the original screws and washers.
prusaprinters
Filament spool holder for Ender 3 style printers.The spool holder has the Creality Ender logo on both sides.It has been hollowed out a bit to save filament and time.Original spool holder design: https://www.thingiverse.com/thing:3544593Spool holder...
thingiverse
A simple roller bearing spool holder that replaces the original Ender 3 spool holder. ...Uses the original pressure clip ring.
thingiverse
Creality Ender 3 Filiment roll holder, fits in original spool holder hole. ... didnt need any support to print ( the thread did need a slight sand and spray with wd40) but tightens up nice
thingiverse
Simple & Minimal Filament Holder You will need two 608ZZ bearings. ... Remix: Curved Roller (https://www.thingiverse.com/thing:4244293) Screw & Nut (https://www.thingiverse.com/thing:3732949)
thingiverse
I use 10x15x4 mm x2 bearings holder and nut print horizontal roller print vertical 20% infill PLA BFplast Roller length 84mm Filament weight 1kg
thingiverse
If you want save some height in the Ender 3d printer that is a good solution. Also is required to used to original spool holder in the assembly. For reference in the project we have some parts not printed displayed in brown. ... Bill of Materials: ...
cults3d
Custom filament hanger using sealed ball bearings for smooth operation. Note that this reduces height capacity of the printer for a little bit. ... Additional parts required: - 1x 120mm M8 bolt - 2x M8 nuts and washers - 4x M3x10mm bolts - 4x hammer...
thingiverse
Custom filament hanger using sealed ball bearings for smooth operation. Note that this reduces height capacity of the printer for a little bit. ... Additional parts required: - 1x 120mm M8 bolt - 2x M8 nuts and washers - 4x M3x10mm bolts - 4x...
thingiverse
Fundo this amazing holder from HugoHuge, but I have some spools that are less thick than the usual and they does not fit on the original design. I remade it to be less thick but fit the rest of the parts from the original. ...
thingiverse
Holds filament spools. Print the base on its flat side. This maximizes strength, and is the reason why the upper hole is offset from center. Print the nut and bolt upright. Perhaps in a future version I will enable the bolt to be printed sideways...
thingiverse
Creality (Ender 3) Filament holder 80mm spools that dose not brake when you print it. ...
thingiverse
This is a remix from Skrutt84's awesome project "Ender 3 - Filament holder DELUXE" I couldn't find any M8 nylon lock nuts, so I had to use three standard nuts. Two of them are used as a nut and counter nut (as jam nut) at the end of thread bar. I...
thingiverse
This is a remix of the Ender 3 Filament Holder by random1101. https://www.thingiverse.com/thing:3353413 It was a great replacement for the stock filament holder that came with my Ender 3 Pro. The stock holder did not turn. I did not like this...
prusaprinters
This is a remix of the Ender 3 Filament Holder by random1101.https://www.thingiverse.com/thing:3353413It was a great replacement for the stock filament holder that came with my Ender 3 Pro. The stock holder did not turn. I did not like this because...
cults3d
This Ender 3 Filament Extension is inserted into the original roll holder.
thingiverse
This Ender 3 Filament Extension is inserted into the original roll holder.
thingiverse
Ender 3 Pro filament spool holder adapter. Remixed from and for use with... ... https://www.thingiverse.com/thing:3209211 Required a 90 degree adapter due to upgrade to 'direct drive' modification.
thingiverse
This is a drop-in replacement for the stock filament spool holder rod that comes with the ender 3. The only difference is that it is shortened to about the length of a standard roll of filament. ... This looks better cosmetically, but more...
thingiverse
... IN OD and is 2.5 IN Wide. it Sits flush with the Inland filament spools from microcenter and slips over the Ender 3 stock spool holder. ...due to the lip on said holder i wasnt able to reduce the slack to zero but its a big difference from stock.
thingiverse
Filament holder with bearings that uses the original bracket on Ender 3. You will need a 16 cm long M8 threadbar. 2 pcs 608Z bearings. 2 pcs M8 nylon lock nuts. And 2 M8 washers. For the "Optional_thread_guide.stl" you will need some glue. ...
thingiverse
Filament holder flopping around? Print this and stop that. ...
thingiverse
https://www.thingiverse.com/thing:3323206 https://www.thingiverse.com/thing:2917932 I created this because the first filament holder end clip wasn't as efficient as i'd like. I'm still in the process of printing it, and will upload a picture of it...
thingiverse
Made this to hold the wider wood filament spool - the tube printed well at: PLA 214C nozzle 20% infill 1.2mm walls 0.24mm layers I printed the nut at 102% scale, just so it had a slight loose fit, although printing at 100% with a high resolution...