ender 3 filament roller guide 3d models
935985 3d models found related to ender 3 filament roller guide.thingiverse
Please leave me a comment and i'd be happy to assist :) Modified the original Ender 3 Filament Roller Guide I noticed there were minimal remixes for the ender 3 pro which seems to have a different design. So decided to modify this one to work with my...
myminifactory
Simple remix of Ender 3 Filament Roller Guide by Holspeed (https://www.thingiverse.com/thing:3052488) to accept filament from below rather than above.
thingiverse
I modified Original Ender 3 Filament Roller Guide by Holspeed according to bearing i already have, Printed very well, Fits perfectly.
thingiverse
Revision of Holspeed "Ender 3 Filament Roller Guide" This is printed using the same settings as Holspeed. ... Utilizing Common 688 Bearing included with most dual Z or Z alignment kits
thingiverse
# Ender 3 Filament Roller Guide Remix Based on Holspeed's excellent [Ender 3 Filament Roller Guide](https://www.thingiverse.com/thing:3052488). It's the same as the original other than some very minor modifications. You don't need this remix if you...
thingiverse
I only had a 6201RS bearing laying around so i modified the filament roller guide by Holspeed to fit for this.
thingiverse
With the Ender 3 the spool holder is normally mounted on top, creating a steep angle of entry, and if left unchecked will wear a slot in the feeder arm. The filament also rubs on the lead screw at the bottom. There are a number of solutions to the...
thingiverse
there are two types of roller with a side for centering (roller.stl) and without (roller_2.stl). in that roller that with a side bearing climbs very tight, it must be pressed with a vise until it takes its position. ----- ...
thingiverse
... to the knob for artistic flare. Make sure your tolerances are dialed in. I had to increase my horizontal expansion by .1mm in Cura for the roller. ...I also needed to use a washer between the bearing and the body piece to get it to move smoothly.
thingiverse
make a pin (cut a piece of 1.75mm filament to secure the pin) to replace the M4 bolt. ... also use the 608 bearing from https://www.thingiverse.com/thing:3002837 08/19/23 add a V1.2 for low mount filament. ...(https://www.thingiverse.com/thing:2948891)
cults3d
2 - spacers Plus you will need: 1 - 608 bearing 1 - M4 x 16mm bolt 1 - We also need a filament sensor like this You also have to download the plugin:https://plugins.octoprint.org/plugins/filament_sensor_reloaded/ and then configure the pin where you...
thingiverse
2 - spacers Plus you will need: 1 - 608 bearing 1 - M4 x 16mm bolt 1 - We also need a filament sensor like this You also have to download the plugin: https://plugins.octoprint.org/plugins/filament_sensor_reloaded/ and then configure the pin where...
thingiverse
From https://www.thingiverse.com/thing:3052488 Ender 3 family's spool holder is mounted on top which made a steep angle of filament entry. This can result in unsmooth filament feed into the extruder. ... the change is done by the following list - the...
thingiverse
Minor Update 20/3/19: Getting the filament smoothly into your extruder feeder is rather important. With the Ender 3 the spool holder is normally mounted on top, creating a steep angle of entry, and if left unchecked will wear a slot in the feeder...
thingiverse
Minor Update 20/3/19: https://www.thingiverse.com/thing:3503227 Getting the filament smoothly into your extruder feeder is rather important. With the Ender 3 the spool holder is normally mounted on top, creating a steep angle of entry, and if left...
thingiverse
Snap on filament guide for a side or top mounted spool for the Ender 3. (Can print without supports) V2 - Stronger. I recommend printing this dust filter aswell to go with it as it will fit between the spool. ... Filament Dust Filter by sneakypoo -...
prusaprinters
Snap on filament guide for a side or top mounted spool for the Ender 3. ...(Can print without supports) V2 - Stronger. I recommend printing this dust filter aswell to go with it as it will fit between the spool. Filament Dust Filter by sneakypoo -...
thingiverse
I loved the design of the original filament roller guide, but I didn't like that you needed screws, and you had to feed the filament through every time you change it. With this version, all you need is a bearing. ...The bearing will slip on and lock...
thingiverse
A roller bearing pulley to guide filament into the extruder feeder ensuring a smoother feed, especially with more flexible filaments. ... Love the way the original bracket is push fit onto the printer - this mod makes it so the pulley is a snap fit...
thingiverse
After changing the Stock Extruder to a BMG Clone I realized that the Filament Guide im using ist not long enough. So I made a remix of the Guide i was using with the Stock extruder. Enjoy. You need a 608er Bearing (or print one) and a M4x16mm...
thingiverse
Simple remix to accept filament from below rather than above.
thingiverse
... of 3x8x4 bearings from RS2205 motors lying around, so I made this remix. ... Print bracket, roller and two spacers. It should be possible to use two bearings instead of spacers, but it isn't really necessary. ... You will also need M3 screw and nut.
thingiverse
... project to accommodate 6000z bearings. Additional credit goes to [this project](https://www.thingiverse.com/thing:5541851) for the roller and bearing. Instructions: Print ring flat on bed. Supports are optional. I didn't need any. ...
thingiverse
This is a remix of https://www.thingiverse.com/thing:3052488. ... I redisigned it to add a filament sensor with role.
prusaprinters
Simple remix to accept filament from below rather than above. https://www.thingiverse.com/thing:3052488 Print instructionsCategory: 3D Printer Accessories
thingiverse
Lighter mounting) - Improved adjustment base/support (modification of the base only) -------------------------------------------- ENDER 3 UPPER FILAMENT ROLLER GUIDE Design inspired by https://www.thingiverse.com/thing:3052488 Compatible with : -...
thingiverse
When I printed Holspeed's Filament Roller Guide (https://www.thingiverse.com/thing:3052488), I realized that it touches the filament filter I was using. This caused friction, and the roller did not spin properly. So I added a roller guard to his...
cults3d
When I printed Holspeed's Filament Roller Guide (https://www.thingiverse.com/thing:3052488), I realized that it touches the filament filter I was using. This caused friction, and the roller did not spin properly. ... So I added a roller guard to his...
thingiverse
The top filament guide connects to the Ender 3's aluminium frame in 2 parts, a small dovetail connection and a filament guide which comes either flat or angled up 30 degrees. The -Flat- arm is good if your spool is mounted to the left of the ender...