ender 3 limit switch replacement 3d models

LED light bar with a switch for the Ender 3 that has a simple but aesthetic look to it. Since the PSU for the Ender 3 outputs 24v, I also made a case/mount for an LM2596 regulator that can mount on the railing back under the bed. Be aware that if...

Here is a front Box to attach to your Ender 3 to give it a place to hold your SD card converter to use full size SD cards, and to add a light switch. You can also find my LED light bar for Ender 3 here: https://www.thingiverse.com/thing:3292889 I...

Having added a bed leveling sensor to the Ender 3, the Z-Stop switch is no longer needed. With this simple mount turn it into a Filament Runout Sensor. ...it is designed to work with or without a pully type Filament guides.

This is a clip that attaches LED lamp switch for Ender 3 V2. ... The LED lamp I used: https://www.aliexpress.com/item/1005002996381987.html?spm=a2g0o.9042311.0.0.3bc04c4dxcBaxi You will need a support for the v-slot nut.

I chose to design and build a compact rocker switch enclosure that snugly fits into the rear V slot of my Ender 3 printer. ...The finished box will sit comfortably atop the power supply, enabling me to easily toggle the power on or off for my LED...

Quick and dirty design of mounting plates for limit switches for the brand new Sculpfun S10 laser. ... Designed for the "Creality Ender Limit Switches", like these https://www.aliexpress.com/item/4000119886874.html

Mounting box for switch to control a light i added to my Ender 3 V2. The t-slot tabs are a little big and will need to be filed down to fit. The switch I used is no longer available from amazon but i am pretty sure the one below is the same.

Just a Basic replacement for the Y Axis and Z Axis limit switch bracket Tevo Tarantula Pro 3d Printer

I needed to modify the original PSU cover on the Ender 3 to add switches for LED strip and raspberry pi so I modeled this one Print Settings Printer Brand: Creality Printer: Ender 3Rafts: No Supports: YesResolution: 200 Infill: 38 Filament: [...

# Ender 3V2 USB Replacement. The MicroUSB port on the front of my 3V2 has been sketchy for years. Recently it got worse, so I found a solution. With a $3 part and some simple (but small) soldering, I now have a USBC port that works the same way as...

Replacement for Y axis Tensioner case. Stronger than the Original. ... Updated 4/6/23

This is my improved Ender 3 V2 Drawer to house my Raspberry Pi 4 and all the tools and spare parts that I used to store in the original drawer. Original design by bohijo1 here: https://www.thingiverse.com/thing:4604339 I shortened the drawer a...

After the countless times that the Z axis endstop failed to activate on my Ender 3 Pro, I decided that I would search for another switch that I could use instead. I took inspiration for the design of the switch mount when I took the original off an...

simple bolt-in replacement for the stock cooling fan duct. ...This new duct redirects the fan air closer to the nozzle and blows onto the part more accurately.

The Ender 3 S1 Pro has a big plastic base that covers up a lot of places where the switch for the 3D Chameleon color changing system could be mounted. I decided to go simple and mount the switch right on the plastic base using 3M Command Strips. So I...

... 1.3, I've connected the endstop to the GND and Signal pins of the X+ connector. On the filament runout sensor itself, the original Ender 3 cable is wired so it goes in the first and third pins (so the switch is connected in a Normally Closed mode).

https://www.youtube.com/watch?v=o1zXYwgIPLY Heres great video(not me) to set it up https://www.youtube.com/watch?v=2l7c3A6_eT4 Link to micro switch...

tools : 1- on off switch can handle 220V or 110V 19x13mm ( i used 220V 3 amp switch ) 2- 220v or 110v and 60_90 cm long power cable, can handle at least 300 or 500 watt to be in safe side 3- printed case 4- modified your End G code in cura ( note :...

This remix was made to fit the Ender-3 Max but should fit any printer with dual V-Slots. It's made for an STSP rocker switch facing upwards. There are three holes on the bottom to allow for front and back light wires, as well as a wire to the power...

In my case, I placed mine at the front right of the base, near the lcd of my ender 3 v2. I printed the case with the opening for the switch faced down to the bed and the opening for the back plate at the top. Supports from build plate are also...

I needed a place to mount a rocker switch for the LED lightbar I added to my Ender-3, and this PCB cover offered the perfect opportunity. This is the version that uses factory screws and has cutouts for one display ribbon cable and the bell. Credit...

...This will ensure the greatest strength of the printed material. To complete the replacement, you will additionally need: 1x M4 20mm screw 1x M4 30mm screw 1x Hot Pin Knurled Injection Copper Nut M4 3mm I hope that some of you will find it useful :)

... ... So I made a new one wich replaces the original one. I made it of 2 parts for easy printing. Assembled without additional material. For protecting the flat cable i also put some stripes of duct tape to it (see pic.) Fully optional. ...

After replacing my X axis Belt tensioner I decided to change my Y axis belt tensioner too, since the printer had looked half baked in my eyes :D Yet again another Quick'n Dirty remix of Cornaly_Cool's design. Thanks mate.. You will need to use the...

I needed a place to mount a rocker switch for the LED lightbar I added to my Ender-3, and this PCB cover offered the perfect opportunity. This is the version that uses factory screws and has cutouts for one display ribbon cable and the bell. Credit...

... shown in the image below. 4. Use discarded PLA to attach the light bars to the print, as demonstrated in the picture below. 5. Enjoy your new DIY kit! This kit is compatible with any Creality printer that has a top rail similar to the Ender 3.

Everything you need to print a double light bar with filament guide and power switch for your Ender 3 v2. The only real modification I made was to the left endcap so it could accommodate two light bars and the filament guide. You will need to...

For this item found at http://www.thingiverse.com/thing:15683, use the Y-axis limit switch counterpart. ...To install it, position it on a 6mm plate and replace the current switch with a micro switch for improved performance.

Explanation of files: Z Limit Main Spacer - this can be used with the limit switch that came with the printer so that it never moves up Z Limit Stock Hotend Mount- This is one piece that replaces the stock Z-limit switch mount and its perfectly...

This is a small switch box that mounts to the leftmost 4040 extrusion on the Ender 3 Pro using the screws that hold the electronics box to the machine. The switch I used is a KCD1-101 from...