ender 3 linear rail y axis 3d models

For the Y-Axis there might be another route by utilizing the upper rail on the back. Update at 2021-01-01: I split the design into two pieces. Now it is possible to place them individually and it saves some filament. I left the original design...

I remixed this for my Ender 3 Pro with x, y, and z linear rails. I modified the cutout in the middle because there is more depth to use under the y-axis with the y-axis linear rails. ...I also used a 0.6 nozzle to print 0.4 lines because the extrusion...

I took a great design from Thingiverse and remixed it to create a better fit for my Creality Ender 3's stepper damper on the y-axis, which had been hitting the metal bed support plate when I installed it. With this new mount, you can use the damper...

The Ender 3 Pro has several differences from its standard counterpart, with one notable variation being a wider Y axis shaft. This difference necessitated breaking parts off of Dauler's version to secure attachment, resulting in instability. Scaling...

... on the top-of-extruder bracket to the left for better alignment 2. Replaces the left-of-the-power-supply bottom bracket with a shorter snap-in for better alignment 3. ...Adds a print bed tension relief termination bracket for the z-gantry chain

Base for mounting direct drive on Ender 3 V2. For X MGN9 Linear Guide Kit purchased from ALI. For mounting on the bearing, I used M3x16mm screws with a countersunk head. The 23mm motor doesn't work very well with this extruder. Not enough power at...

Remixed y-Axis stepper motor mount to hold a 42-40 stepper motor. Wanted a stronger motor for the Ender Extender kit's larger/heavier bed. Can fit motor with dampener just barely. Dampener:...

The 4mm Versions are designed to fit the 4mm thick y carriage plate that comes with the Ender 3/pro. The "Spring" versions are for use with springs and the "Bung" is for use with the silicone bungs as shown in the picture. ... Requires: 4x 10-15mm m4...

Modeled a clip to hold the back of the camera housing on.

Modeled a clip to hold the back of the camera housing on. ... Category: 3D Printer Accessories

Digital Leveler: http://ali.pub/332z86 Ender-3, CR-10 Cable Extender: http://ali.pub/311l9t 90 Watt Hot Air Gun: http://ali.pub/359eon Third Hand for Soldering: http://ali.pub/359f2g CREALITY ENDER Store: http://ali.pub/323yh5 TRONXY Store:...

Stepper Motor Mount on Ender 3 Solved Belt Position Issue. Thin Motor Mount is Fixed with Added GT2 16-Teeth Pulley. Another Advantage of This Motor Mount is That It Works Like a Damper, Making the Motor Extremely Quiet. BOM: 1 x GT2 16-Tooth 3mm...

This 3D printed part will swap out the existing back left nutwheel with a smaller version, enabling you to install the y-axis dampener mod and heatsink. The original nut would interfere with the heatsink or motor if you added a dampener to the y...

The spacers on the underside of the part attached to the 3d printer structure were removed, for a better fit of the screws on the Y axis bar. ... You may have to force the part a little bit into the thread, if necessary, force the part where the belt...

The spacers on the underside of the part attached to the 3d printer structure were removed, for a better fit of the screws on the Y axis bar. ... You may have to force the part a little bit into the thread, if necessary, force the part where the belt...

This is a SD card mount for Creality Ender 3. 08.16. 2018 - added ver. 0.2 (img. 3, 4 and 5) - same functionality but a tighter fit. Parts you'll need: 2 M2/6 screws 1 SD card extension cable. ...https://www.amazon.com/gp/product/B0749S1S15?th=1

THE LEFT SIDE COVER GLIDES SMOOTHLY DOWN OVER THE Y-AXIS ASSEMBLY, ITS GROOVES PERFECTLY ALIGNED WITH THE METAL PLATE. ...ON THE RIGHT SIDE, HOWEVER, A DIFFERENT SCENARIO PRESENTED ITSELF DUE TO COMPLEX WIRING ARRANGEMENTS, REQUIRING A SPECIALIZED SPLIT...

ender5_belt_tensioner_y_axis_part_1_v1.stl ender5_belt_tensioner_y_axis_part_2_v1.stl ender5_belt_tensioner_y_axis_part_3_v1.stl ender5_belt_tensioner_y_axis_part_4_v1.stl ender5_belt_tensioner_y_axis_part_5_v1.stl Other Required Parts: 1x Idler...

This is an SD card mount designed specifically for the Creality Ender 3 printer. 08.16.2018 - Version 0.2 was added, featuring images 3, 4, and 5. This updated version provides a tighter fit without compromising functionality. ... To assemble this SD...

This is a custom mount for the Creality Ender 3 SD card. To create this mount, you will need to gather the following parts: two M2/6 screws and an SD card extension cable that can be found at Amazon through the link provided...

I replaced my Y-Axis belt with a LeadScrew, a change I'd been considering for ages. Until today, I was using NEMA 17 motors on all axes. To boost torque, I swapped the pulley and have been thrilled with the extra power from this tiny motor. However,...

After having tried a couple other designs that turned out to be too small I came up with this design which was based originally on Tension Wheel Cover Knob Ender 3 V2 by sijosijo11 January 02, 2021 https://www.thingiverse.com/thing:4706821. Again...

Hardware ------------- Linear Rails: • (24) M3x10mm socket cap screws • (24) M3 t-nuts X-Carriage Mount: • (4) M5x20mm socket cap screws • (4) M5 nuts • (2) M5 washers (reuse existing) X-Carriage Linear Rail Block: • (4) M3x10mm socket cap screws...

Improved Y-Axis Leading Rods Reinforcement. ... Print Settings Printer: CTC Dual Rafts: Don't Care Supports: Not Needed Resolution: 0.2mm Infill: 70% Notes: Two Shells

Relocates the Y axis stop sensor to the back rail to allow for horizontal movement for exoslide plates

the sensor mount by bastelgarage worked great! ... I did not want to insert gromets so I shrunk the holes in order to use the screws that came with the sonic pad. The same screws used to mount to the X axis print that came with the sonic pad.

... to print the other parts to this, just click on the link in the bottom. I added 2 designs, one with the Ender name and dragon head Logo on either side and a plane one. Take your pick. I suggest printing at 100% infill. ... Happy printing.

My take on the ender 5 plus liner rail. Used it before going to the Merc 1 setup.Heat Inserts are required for this to work well. It GRIPS the Y gantry well, I was able to have serious speed compared to OEM Setup.

Hey Guys, this is probably one of the best upgrades you can do to your S1 prothis aligns the probe with the nozzle on stock hot ends, this is needed for couple of reasons but the most obvious is if you suspect you have a bent Y extrusionthe new...

use the pins or screws