ender 3 meanwell power supply 3d models
862539 3d models found related to ender 3 meanwell power supply.thingiverse
My stock Ender 3 power supply went bad and I replaced it with a Meanwell. The Meanwell power supply is much thinner and the stock cover doesn't fit. I did not like the options available that required you to bend pins or use additional mounts into...
thingiverse
I didn't like the idea of removing screws to install a duct so I created a crude remix so magnets could be used. I used small magnets I got from Harbor Freight and they measure approximately 8mm x 2mm PN 67488. The recessed holes for the magnets...
thingiverse
I fixed Eigengrow's modified power supply silencer so that the holes are the correct diameter for the stock screws (as pictured). I also reduced the thickness of the mounting points because the stock screws are not long enough to go through the...
thingiverse
Very simple remix of the [Ender 3 Power Supply Fan Silencer](https://www.thingiverse.com/thing:3328495) by [Eigengrow] (https://www.thingiverse.com/Eigengrow/about) so that it fits the Ender 3 Pro Meanwell power supply. I printed off a few layers...
thingiverse
I took the Ender 3 Pro Power Supply Baffler from calaverajoe, but I didn't like how thin it was, so I made it thicker
thingiverse
For installation need to discard the bottom cover
thingiverse
I haven't found what I've needed, so I designed this extra rigid PSU mount for Ender 3 Pro (Meanwell PSU). It slides inside 4040 extrusion with a tiny bit of force to ensure there's no wobble at all. There's a plenty of room between 4040 extrusion...
thingiverse
Ender 3 Pro Power Supply Meanwell Silencer Baffler designed with 1.2mm walls thickness for extra fast print on 0.4 or 0.6 nozzles. Use existing bolts to attach it to your power supply without disassembling it (take out one screw, attach it to one...
thingiverse
I modified szkryb's MeanWell power supply model so that I could have an additional opening for powering my control board and LED relays. Features ------------ • Removed the 1.5mm gap at top from the original model. • Adjusted mounting holes...
prusaprinters
I used the Heavy Copper font from dafont.com/heavy-copper.font most of the He is risen logos i saw online were a bit feminine, the Gothic feel changes that a bit. Print Settings Printer Brand: Creality Printer: Ender 3 ProRafts: No Supports: ...
thingiverse
Instead of attaching this to my Ender 3, I've decided to use it as a standalone piece. I've sealed up the hole on the rear, and flattened the bottom, to be used as a vertical stand. The power switch is on one side, and there is space for 2 or more...
thingiverse
... with stand. > >Compatible with: Meanwell LRS-350-24 PSU HiLetGo 5V 1 Channel Relay Module With Optocoupler with High or Low Level Trigger > >Remix Sources: >PSU stand: thingiverse.com/thing:4123532 >Relay holder: thingiverse.com/thing:4186335
prusaprinters
I replaced the power supply that came with my Geeetech A10 by a Mean Well power supply - the same power supply type used by my Creality Ender 3 Pro.I could use the bracket of the original power supply (all screw holes were at the same places) with...
prusaprinters
<p>This is a 120mm fan mount I have designed from scratch for a 120mm fan (Specifically I had Corsair SP series 120mm PWM fans laying around). </p><p><strong>PRINTING DETAILS:</strong></p><p>When printing, make sure to combine “Fan filter...
thingiverse
This is the cover for power supply of Ender 3 If you want to change to MeanWell LRS 350 - 24v (or same things) Advantages: 1. Can use the plug with fuse from original one 2. ...The design with air circulation hole to make air move easily You also...
thingiverse
Since i was 3d printing this, thought i'd through a cross and He is risen on it. came out well. ...I used the Heavy Copper font from dafont.com/heavy-copper.font most of the He is risen logos i saw online were a bit feminine, the Gothic feel changes...
thingiverse
Ender 3 V2 drawer replacement for Raspberry Pi with Meanwell Power Supply Space for MEANWELL original RS-15-5 5V 3A Single Output Switching Power Supply AC-DC (I first used a DC/DC converter but it brunbed up so I decides to use an extra Power Supply...
thingiverse
Very simple remix of the Ender 3 Power Supply Fan Silencer by [Heikomarx] so that it fits the Ender 3 Pro Meanwell power supply.
cults3d
This is a remix from https://www.thingiverse.com/thing:3023240 to fit the Ender 3 Pro/Meanwell power supply which has only one screw at the back. It uses the original screw (if you want to). No supports needed (if printed with 0.2 layer height or...
thingiverse
This is a remix from https://www.thingiverse.com/thing:3023240 to fit the Ender 3 Pro/Meanwell power supply which has only one screw at the back. It uses the original screw (if you want to). No supports needed (if printed with 0.2 layer height or...
thingiverse
After upgrading my Ender 5 Plus board to an BTT SKR Pro V1.2 board, my power supply needed to shift positions a little bit. Designed this bracket to allow for several positions. The 4mm holes are 3.3mm for tapping or just thread the screws into...
cults3d
Mount for a single Meanwell power supply. ... Elevated to enable wiring to run underneath.
thingiverse
PSU Cover for Meanwell RS-75-24 Currently using as a second supply for a custom printer build. Fits supply exactly. ... Printed in PETG with 20% infill / 3 perimeters / 5Top/5Bottom Layers.
thingiverse
This is an external mount for the 500W Meanwell power supply ( RSP-500-24 ) that comes with the Ender 5 Plus. It consists of a top cover, bottom cover, and power switch/plug holder with a cover. The power switch/plug holder uses the existing power...
thingiverse
Also: the Original ender 3 uses a thicker power supply, this remix wont fit! ... ----------------------------------------------------- ----------------------------------------------------- Take a look at my other project/things: Ender 5 dual z axis...
thingiverse
Parts list so far: various 4mm screws (6mm countersunk are ideal for mounting the PSU, and ~10-12mm are good for the powerpole mount.) Delta SK-015A Cherry LRA22H2BBRLN 16AWG wiring of various colors Powerpoles and connectors Errata I wanted more...
thingiverse
The source model has tapered head screws to mount to the underside of the power supply. I modified this to support socket head cap screws instead. There are 2 models included. One will require supports for decent printing where the socket head...
thingiverse
When hanging the power supply, the powerplug "hanging" did not work for me,