ender 3 pro filament sensor 3d models

Ender-3 Pro Filament Sensor Mount Remixed from filament guide: https://www.thingiverse.com/thing:3052488 The filament I bought from Amazon (2 pack) $11 https://www.amazon.com/dp/B07N2GQHQT

I'm adding filament sensors to my printers, and found this design that combines the microswitch holder with a filament roller guide: https://www.thingiverse.com/thing:3357097 The design did not attach very securely to my Ender 3 Pro. I was already...

I'm adding filament sensors to my printers, and found this design that combines the microswitch holder with a filament roller guide: https://www.thingiverse.com/thing:3357097 The design did not attach very securely to my Ender 3 Pro. I was already...

Just modified this filament sensor mount for my Ender 3 Pro. I stretched out how far the sensor is from the extruder, so there is a little room for the filament to clear the sensor after running out. My machine automatically extracts the filament...

This is a simple mount for a filament runout sensor that fits the Ender 3 / Ender 3 Pro printers. See the image to determine whether it will fit the specific sensor design you have. The filament intake tube was designed so that it can accommodate a...

Ender 3 Pro Filament runout + Guide, this goes over top of the leadscrew and screws down. I've used the same micro switch as what is on the ender3's end stops, I've upgraded to a BL Touch so i used the z-axis micro stop for this project. Using this...

###Ender 3 Pro Filament Out Sensor### **This sensor circuit is based on the 555 Timer IC and will create an oscillating beep (i.e. ...continuous beep beep) when your filament runs out.** **PARTS LIST** (1) 555 Timer IC...

###Ender 3 Pro Filament Out Sensor### **This sensor circuit is based on the 555 Timer IC and will create an oscillating beep (i.e. ...continuous beep beep) when your filament runs out.** **PARTS LIST** (1) 555 Timer IC...

Remixed the "Ender 3 Filament Sensor and guide" by rghawi in order to add some chamfer to the piece so that these sensors (see below for link) would fit. ...Previously, the sensor was so big that the button was pressed with it in the sensor guide (need...

I found several versions and remixes for reusing your old Z axis endstop as a filament runout sensor, but none seemed to fit the endstop from the Ender 3 **PRO**. Well, now one does (**Hopefully.** I have printed it, mounted the endstop, and tested...

Required : 2x Micro Switch v-156-1c25 or other option --> <a...

Filament sensor holder and Filament Guide for ender 3 printer or others with some changes. Developed based on the standard filament sensor available on...

Remixed the Ender 3 pro filament runout sensor by blaiseb with slot for bowden tube.

This is a filament runout sensor for Ender 3. The sensor is based on the Z end stop of the printer. I replaced this with a BLTouch. The sensor is screwed onto the vertical axis. I have adjusted the printer firmware. Unfortunately, I had to deactivate...

I was looking for a filament runout sensor mount for my Ender 3 Pro. I don't in any way care for the ones that hang on the filament. That just seems like problems waiting to happen. DorkyTim has a nice design that routes the filament just pass the z...

I was looking for a filament runout sensor mount for my Ender 3 Pro. I don't in any way care for the ones that hang on the filament. That just seems like problems waiting to happen. DorkyTim has a nice design that routes the filament just pass the z...

(Description in german below // Deutschsprachige Beschreibung folgt unten)Since I recently mounted a BLTouch on my Ender 3 Pro, I no longer need the mechanical Z-axis end switch. I have now converted it into a filament runout sensor and designed a...

:-)__ ---------------------------------------------------------------- Da ich kürzlich einen BLTouch an meinem Ender 3 Pro montiert habe, benötige ich den mechanischen Endschalter für die Z-Achse nicht mehr. Diesen habe ich jetzt in einen...

(Description in german below // Deutschsprachige Beschreibung folgt unten)Since I recently mounted a BLTouch on my Ender 3 Pro, I no longer need the mechanical Z-axis end switch. I have now converted it into a filament runout sensor and designed a...

:-)__ ---------------------------------------------------------------- Da ich kürzlich einen BLTouch an meinem Ender 3 Pro montiert habe, benötige ich den mechanischen Endschalter für die Z-Achse nicht mehr. Diesen habe ich jetzt in einen...

holds a generic filament sensor from amazon with mounting holes off to the side vs in the center snaps on the end of the frame near the Z scew on top. ...only for stock top filament roll holder.

While I love the clean and simple design of Sebastiandruckt's version, I did find that it makes filament change quite annoying because the filament exit is offset from the extruder's filament-in port. This is an attempt to fix this. Also, the...

CREALITY ENDER-3 S1 PRO - FILAMENT SENSOR HOLDER Creality Ender-3 S1 Pro Upgrade and Modification, enjoy our Version. If you have any Questions, just write a Comment DISCLAIMER This Product may only be printed for Personal use and may not be Sold...

I remixed the version for the Ender 3 to match the dimensions of the Ender 3 Pro. Ionize's version had the guide and sensor 4mm over to the left which didn't leave a straight path for the filament. The sensor I used is a cheap one from aliexpress...

Combined the runout sensor with guide by blaiseb (https://www.thingiverse.com/thing:3357097) with the attachment method of the runout sensor by murphmandan (https://www.thingiverse.com/thing:4337798) To physically attach the sensor and guide to my...

... and aluminum extrusion. WARNING I HAVE NOTICED ON MY ENDER 3 MAX THAT WHILE PRINTING AN ITEM THAT UTILIZES THE FULL ZED AXIS THAT SOME FILAMENT BINDING MAY OCCUR, i have not tested on my ender 3 pro as it is not currently setup for direct drive.

This is a remix of [Filament Runout Sensor w/ Creality Limit Switch](https://www.thingiverse.com/thing:4547442) The original Sensor is good, but I created this remix because I needed a sensor for my Ender-3 Pro and it is in an enclosure. The...

I needed to have enough space between it and the filament runout sensor, so I pushed the sensor back a ways. I now have enough room for the filament to feed past the sensor when it runs out, but not get to the oiler. Now when my filament runs out,...

... it mounted to an existing screw on the Z rod. I set the run-out distance to 10mm in Marlin firmware so it prints until the filament leaves the run-out sensor to prevent it from pushing back under the arm of the switch and potentially damaging it.

This new design enables the filament sensor to rotate freely, effectively preventing any tangling or snapping of the filament. I thoroughly searched through Thangs to find the simplest yet dependable bearing for 3D printing. Despite this, I still had...