ender 3 pro layer shift 3d models

Air-tight housing for Ender 3 Pro users can be achieved by modifying the existing components. The screw dimensions remain identical to the original setup, ensuring a seamless integration process. Upgrading to a higher fan can significantly reduce...

A collection of extruder spinners I designed for the Ender 3 S1 Pro sprite extruder. I'm unsure if they will work with other makes/models but they print quick, so give it a go! You will need to buy some 4mm dia x 3mm thick magnets for these spinners...

Having recently acquiring a Creality Ender 3 Pro, I fell in love with everything about it, except for the plain power supply stuck to its side. I decided to create this project to tidy up the visuals a bit. Secure the new housing using double-sided...

This is an upgrade from the 'Simple touchscreen upgrade stand Ender 3 Pro'. With the extension it is possible to change the inclination of the touchscreen for better visibility. The stand itself has an extra hole to be able to tighten the...

This is a remixed bed level lock for the Ender 3 Pro. The friction parts have a ball pattern with a resolution of 36 steps per rotation. Each step has a movement of 10 degrees. This gives a very nice and precise adjustment of the bed in addition...

The Meanwell LRS-250-24 power supply's built-in fan on my Ender 3 Pro is extremely loud and operates sporadically. To upgrade, I'm installing a standard 92mm PC case fan using an adapter. The necessary screws are the four self-tapping ones that come...

There are numerous microSD card holders for the Ender 3 Pro printer available, but I'm looking to create one with a personalized touch - a phrase engraved at the front that perfectly aligns with my printer's design. To simplify the printing...

As per BDWW's original post: This mount is designed to secure a Wyze Cam on the front roller bracket of an Ender 3 Pro. It simply clips onto the existing bracket. I simplified the design into one piece and rotated it vertically for easier...

... use with this filament run-out sensor along with BLTouch. I think this one from creality website should work fine:GD-Ender-3 Pro-HW-V4.2.2-SW-V2.0.8.23-CRTouch-FilamentEuropeMultiBearing dimensions: outside dia:22mm x inside dia: 8mm x width: 7mm

LED strip mount for the Ender 3 (Pro) or a printer with an extrusion to bolt to. I used an LED kit from PROJECITY, but any 10mm LED strip should work just fine. https://www.amazon.com/gp/product/B0B44P5SFP/ My original was a bit too thin at...

The Ender 3 Pro's buzzer is a persistent annoyance, and it's time to silence its cacophony. To reduce the noise emanating from this device, first locate the buzzer itself, which is usually situated near the extruder. Next, inspect the wire connected...

Wenn Du bereits eine hast (von Ender 3 Pro), wird sie nicht benötigt.Spool Holder Washer.stl --> Das ist die Beilagscheibe. Diese wird nur dann benötigft, wenn die Verbindung irgendwann mal locker wird.. Ich habe den oberen und unteren Teil in PLA...

I wanted an enclosure for my Ener 3 pro to be able to better print ABS. I needed a thermal blanket but that needed support so i designed the Longarms to hold the top. The spool holder was an issue so i created a holder that would allow me to easily...

In order to covert my Ender 3 Pro from straight 3d printing to Laser Engraving, I purchased the Creality 1.5 mw laser attachment. Once I received it, I realized that I wanted to make a permanent conversion rather than just utilizing the magnets...

sensor offset: x=28mm Y=3,25mm Z=-2,43mm Modification kit to mount a Pheatus Dragonfly BMS on the Ender 3 (Pro). The adapter is necessary so that the heat block including the silicone sock does not hit the carrier plate of the Ender 3 (Pro). The...

I had an old iPad 2 lying around and decided to mount it to my Ender 3 Pro as an Octoprint controller. I printed it on edge with supports for the right section. I was concerned about weight and balance so added v-slot extrusions on 3 sides. It also...

... 10. **Integrate a heated chamber**: Improve temperature control and reduce warping by adding a heated print chamber. These modifications will significantly enhance your Ender 3 Pro experience, allowing you to produce high-quality prints with ease.

Finally, I increased the size of the hole for the largest hex key as mine wouldn't fit. This is a quick print (about 3 hours) that doesn't use much filament and is able to hold all the tools that came with my ender 3 pro. I printed upside down, with...

This is a Raspberry pi 3B adn 3B+ case (for octoprint/octopi) that can slide into the v-slot extrusion of Ender 3 and Ender 3 Pro behind the display. I wanted case where no cables would be running into the Raspberry Pi from the sides. I couldnt find...

This is a Raspberry pi 3B adn 3B+ case (for octoprint/octopi) that can slide into the v-slot extrusion of Ender 3 and Ender 3 Pro behind the display. I wanted case where no cables would be running into the Raspberry Pi from the sides. I couldnt find...

https://paypal.me/cdsmakestuff A storage drawer for the Creality Ender 3 Pro. Compartmentalized for various items, including 9 nozzles. Designed to be no higher than the 40/40 extrusion of the base. Wanted the clearance below the bed for easy access...

This is a fairly accurate representation of the x-axis limit switch on my Ender 3 Pro. I took the STEP file from [Creality's...

**It only fits the Ender 3 Pro with a 4040 center extrusion.** This bracket is needed because some Ender 3 Printers are shipped with pressed pulleys on the stepper motors. Those pressed on pulleys can't be adjusted along the shaft of the motor. All...

Hello, As I'm currently in the process of upgrading my Ender 3 Pro to Octoprint, I purchased a Logitech C270 Webcam to use with it. As I wanted a basic, adjustable arm that leaves the V-Slots empty for covers to put in them, and since I didn't...

The author has created a hybrid printer by combining two Ender 3 Pro printers and upgrading them with various components. Here's a summary of the key points: **Upgrades:** * Dual motor mounts for all axes * Upgraded motors not necessary, but can...

... It turned out okay. But one day, I might redo it and print it again - haha. I also remixed another design, the PS Tools Holder from Thingiverse. Printer: Creality Ender 3 Pro (https://amzn.to/2Pmm73v) Material used: PLA (https://amzn.to/2OYee5g)

I was having a hard time finding a model for a LED Light Bar for my Ender 3 Pro, so I decided to make one. I used 2x 250mm white 12V LED strips and a LED switch. The Ender 3 Pro has a 24V power supply so I needed to drop the voltage to 12V. To do...

**Creality - Ender 3 Pro** This set of covers is designed specifically for the Creality Ender 3 Pro. The files are labeled according to the overview drawing, with each cover part marked with a number indicating where it goes. **Cable Management**...

A Spool Holder for my Ender 3 Pro. Fits the Original Bracket also Required: 1x M8 Threaded Rod l= 145mm 1x M8 Nut 2x M8 Domed Nut (you could use normal Nuts...) 3x M8 Washer 2x Ball bearings 8x22x7mm (typically used for Skate Wheels) now the...

... pulley, bearing, offset) without full disassembly. Just slide it off :) Print Settings Printer Brand: Creality Printer: Ender 3 ProRafts: No Supports: NoResolution: 0.2 Infill: 20-25% Filament: Fiberlogy PLA Onyx Category: 3D Printer Parts