ender 3 psu control 3d models

This is a Meanwell 350-24 PSU stand for an Ender 3 V2. The power supply was not getting as much air as I think it should tucked away under the printer. This is a stand-alone option and I used some 200'C silicone 16 gauge wire to connect the PSU to...

A replacement for the mainboard housing that revolutionizes the Ender 3's electronics setup, consolidating everything into a single box efficiently cooled by a powerful 120mm fan. This upgrade replaces the noisy stock fans with a much quieter setup,...

I decided the pi should run off the Ender 3's PSU, so I went for a USB powered route instead of hard wiring a buck converter. I used this buck converter - https://www.amazon.com/gp/product/B07121W7Q4/ - and others would probably work just as well,...

**PSU Case:** • Print time: approx 10 hours • Infill: 20% • Layer height: .3 • Initial layer height: .32 • Speed: 65mm/s (80 infill, 130 travel) • Supports: Enforced **PSU Plate:** • Print time: approx 3 hours • Infill: 20% • Layer height: .2 •...

I Made the Cap for my Ender 3 Pro. ...It shows the direction to turn up a value. Pretty simple bute awesome grip, takes under 2h to print. The Cap fits perfect on Ender 3 Pro (Bought 2021)

PSU cover for **Creality Ender 3 Max**. I think it fits multiple PSU's from Creality. Replaces both the PSU metallic cover and the plastic housing for the power button and power socket. Reuses the factory screws from the metallic cover. As stated...

Simple power supply cover replacement to install silent fan on Ender 3v2, but it should also fit 3 & 3 pro. I designed it for the Meanwell PSU, so idk if it fits the earlier PSU. None of the available options worked with the 92x25 silent fan I had on...

To make my Ender 3 a little more silent i tried one of these PSU fan ducts. Even if they are called "silencer" it made it even louder cause the air has to be pushed throu the duct too and that makes some noise. So i decided to just move the fan from...

Designed by printXD for the Ender 3 pro and ender 3 Doesn't need any support but I suggest using a layer height of 0.16 or 0.12 for the best looking results. Go look at profile for more cool and interesting upgrades for the ender series printers. ... ...

This is a remix of Ender 3 v2 PSU cover silent mod by sectorone. It didn't fit well within the bed limits, so I chopped it up to make it more printable. You will want 2 M3x8 screws to secure the panels together. May need a 3mm tap to get some good...

This is a remix of Ender 3 v2 PSU cover silent mod by sectorone. It didn't fit well within the bed limits, so I chopped it up to make it more printable. You will want 2 M3x8 screws to secure the panels together. May need a 3mm tap to get some...

(https://www.reddit.com/r/ender3v2/comments/lto6uq/ender_3_v2_all_noctua_fans_buck_converter/) The PSU cover chilluniverse designed (https://www.thingiverse.com/thing:4567153) looks awesome! One issue, I had to print it sideways due to its...

A remix of Ender-3 axis cheat badge by infooverload. ...This model is just a simple ender logo and is 1.5mm thick with logo at .5 thick for at total of 2mm thick.

I found those really nice designed and remixed PSU Covers for the Ender 3 V2. The original design used a 92mm Noctua A9x14 Fan which was just screwed into the cover, the remix I am referencing added a cable guide and a fan holder but uses a 80x10mm...

For fastening it I used 2pcs M4x16mm screws with washers and hammer nuts. Measurements: PSU size: W50xL113mm Fastening holes: 2x4,2mm Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Doesn't Matter Supports: Yes Resolution: 0,20mm...

I took a few other designs/models and diced them up into a new control panel for my Ender 3 Pro printer. It may fit the Ender 3 also, but it has "Pro" written on it. With the addition of the SD card reader and holder, everything is now right where it...

This is a custom cover for the stock Ender 3 power supply that adds a USB socket to power a Raspberry Pi running OctoPrint. It also includes a divider between the mains AC section and the low voltage DC section of the cover, as well as a mount for...

I wanted the pi to run off the Ender 3's PSU, and went for the USB powered route instead of hard wiring a buck converter. Here is the buck converter I used - https://www.amazon.com/gp/product/B07121W7Q4/ Others would probably work just as well, I...

After looking for mounting brackets to relocate my Creality Ender 3 Pro PSU so I could put my printer inside the Creality enclosure, I decided to design my own. I needed brackets to be able to relocate my PSU separately from the printer so it didn't...

A guard over the PSU wire terminal .This is part of my attempt for better cable management of the Ender3...

I remixed is because the original design didn't have enough width for the cables to exit the PSU compartment. The original power supply cover for the Ender 3 v2 (and v2 neo) restricts the airflow to the power supply so the fan ramps up to max speed...

Cable Management System: A Simple Cable Guide for Ender 3 V2's PSU. This cable management system mounts directly to the end of your 80/20 extrusion, utilizing threaded M5 screws with up to .35 diameter heads. To print this cable guide, use PETG...

I've been struggling with warped parts detaching from the bed (a solution involving more than just an enclosure and remote electronics is necessary), so I created this simple remote control panel to enclose my Ender 3. It's engineered to accommodate...

Bracket for a front-mounted Ender 3 Pro MeanWell power supply. Works well with any choice of back-mounted electronics box. Each side of the PSU is sandwiched between two parts which are fixed in place with 2 M4x6 screws each. Ones on the right have...

The 3D model in the pictures are from a Creality Ender 3 and have adapted the necessary dimensions for this project to my Creality Ender 3 pro. When removing the support, I always first pierced the edge between the support and the part with the...

The print was done using CURA with settings of 0.6 mm layer thickness, 0.48 layer height, Ender 3 Stock CURA profile, PLA material, and Tree Support (a Cura experimental feature). To achieve better results, remove normal supports when you select...

Simple Support for Ender 3 Pro Power Supply

beafy version for fanless psu

I didn't like the smooth knob that comes on the Ender 3 so I designed this cover that has grooves for great grip. This was intended to be printed with TPU filament. ...It just slides over the existing knob.

I found those really nice designed and remixed PSU Covers for the Ender 3 V2. The original design used a 92mm Noctua A9x14 Fan which was just screwed into the cover, the remix I am referencing added a cable guide and a fan holder but uses a 80x10mm...