ender 3 rail upgrade 3d models

Feet for the ender 3 v2. Gives you about 40mm of ground clearance. ...Note that the rear legs are different beacause of the psu cover

These are the files that arrived with my Ender 3... ...A squirrel Chessboard :-)\r\n\r\nAnd a test pup.\r\nhttps://www.thingiverse.com/thing:2879047

Fits in filament hanger support bolts. ...Tested in Ender3 v2, I guess Ender 3 and Pro have the same system, but not tested. ...No support needed.

supports for Ender 3 and Ender 3 pro and printers using aluminum profiles. They are designed to be brutal to the eye. You gain height for your printer, improve the ventilation of the plate and also allow the wiring to pass better. ...This model is...

This modification enables the installation of two fans on a Creality Ender 3 or CR-10 printer, enhancing airflow and print quality.

Because of the poor support from creality and my broken cableclip on the ender 3 S1, i redesigned the original cable clip. ... Printed with PLA+ it should work ;)

I wanted to attach two spools to my Ender 3 at the same time, so I designed and built a straightforward spool extension system.

This is a tool tray for the tools of the ender 3. ... When the part appears realy small in the slicer try to make it 1000%.

Fits the BLTouch and 3DTouch for Ender 3 or Ender 3 PRO Special features -The Extruder Fan Cover can be removed independently (no need to also remove the BLTouch mount), thus not messing up the probe Z offset -Optimized cable placement. -Small and...

SHOW_ARM This will show the arm part SHOW_BASE This will show the base part which is screwed to the Ender 3 rail. SHOW_MOUNT This will show the camera mount part. It is designed to be used with a 6x50mm screw at as the hinge. After finally...

I designed this PSU front cover for my Ender 3 Pro. Unlike the other models i found it fits flush and you can reuse the self-tapping screws from the original front cover. ...This was designed for a noctua 90 mm fan, but i reccon you can use any 90 mm...

I designed this PSU front cover for my Ender 3 Pro. Unlike the other models i found it fits flush and you can reuse the self-tapping screws from the original front cover. ...This was designed for a noctua 90 mm fan, but i reccon you can use any 90 mm...

Ender 3 Fan Duct Insert for Secondary Fan: Improving Bridging Cooling and Reducing Air Flow Issues. Not Happy with Stock Fan Duct's Performance in Directing Air to Print Area, So Created Custom Insert. The Insert is Made of Five 45-Degree Duct Pipes...

Pokemon Ender 3: I've made some thematical extensions at or school for our Ender 3 printers! The files are all remixes from excisting files found at Thingiverse. I;m sorry that i didn't remember how to find the original files and makers.... But for...

I made it for my ender 3 s1, but it should work for other enders too, if they have 2020 aluminium extrusion on top. ...It does limit z axis a bit so if you are going to print high objects then take it off. Please note: Print the screw on the side...

I designed a box to add new features to my Ender 3 like: - Have remote control of the printer from your smartphone (Printoid) - Turn your printer on or off - Turn the light on or off, useful when a camera is installed see link below to understand and...

brackets for Ender 3 and Ender 3 pro and printers that use aluminum profiles. they are designed to be brutal to look at. ...you gain height for your printer, improve the ventilation of the board and also allow for better cable routing.

... which operates flawlessly. ...I also successfully printed the Creality Ender 3 spool holder extension; however, one minor problem arises: it causes the bracket to droop slightly. ...To rectify this issue, I created a spool jack that provides stability.

"I'm really excited to share with you a custom mod for your Ender 3 that takes advantage of the existing Z-axis threaded rod brass lead screw fixing screws. ...\r\n\r\nBe sure to check out my other Ender 3 mods on Thingiverse -...

materials: hammer nuts 8 8 screws m3 16 threaded rod diameter 6 2x 45.5 cm makes it possible to make the chassis of the ender 3 rigid materials: hammer nuts 8 8 screws m3 16 wire rod diameter 6 2x 45.5 cm Allows to make the frame of the ender 3 rigid

Just a nice knob that lets you add a nice pop of color to your Ender 3 v3 SE's controller.Might work on similar Creality printer (Maybe Ender 3 v2) if you want to try it please let me know if it works. ...:)

This is a simple cable clip for the Ender 3 or Ender 3 Pro. It uses the stock hardware for the 2 idler wheels on the right X carriage. ...I used this since I moved all my wiring to an outside housing to keep them form getting too hot inside the printing...

... plus PDF drawings of the mechanical components. ...Creality has shared them on their GitHub page at https://github.com/Creality3DPrinting/Ender-3, making it simpler to modify or duplicate existing parts and even create custom addons for your printer.

My Design for a Custom Fan Cover on the Creality Ender-3 Takes Shape After months of planning, my custom fan cover for the Creality Ender-3 is finally coming to life. ...I've managed to get it printed and, so far, it's a resounding success.

The Ender 3's Noise Absorber: A Game-Changing Accessory Are you tired of the Ender 3's loud printing noise disrupting your workflow or household? Do you want to create a more peaceful and productive environment while still enjoying the benefits of...

... have a similar design. ... I printed it in PLA filament WITHOUT supports at .24mm / .28mm layer high (since you don't need much detail) and at 50mm/s (all with the ender 3). ... The print will take about 8 hours for the case and 5 / 6 for the drawer.

You can stash your tools right here for your Ender 3. ...Plus, a caliper is also storage-friendly. To secure this, use the extra screws (M4*14-P) and t-nuts that come with your Ender 3. ...If you've got some improvements to share, just let me know.

A convenient holder for frequently used tools, such as tweezers, nozzle cleaners and an 80mm scraper, which come with the Ender 3 printer. ... It utilizes the side of the aluminum extrusion to create a more robust structure than many other tool holders...

This remix of the Creality CR-10 Filament Guide is specifically designed for the Ender 3, featuring a key modification: the PTFE tube now runs directly perpendicular to the extruder, eliminating the angled orientation found in the original design. ...As...

A nice change if you don't like your square printerhead that comes with the ender 3. as a version of the mimimus you will be able to slide in and out the fans. ... this version works with the stock ender 3 fans.