ender 3 raspberry pi 3d models

None of the existing Raspberry Pi stations I found included accommodations for fans, proper airflow, camera cables, the USB port, either HDMI port or the audio jack. This design aims to address all of those issues. The base clips to the existing...

I am planning to make another LCD screen into the top cover, for OctoPrint. I have included the f3d design files so you can make changes and tweaks. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 0.2...

Meshed together two different Camera Mounts that were already on Thingiverse to create a Ender 3 S1 mount that works with my Octoprint camera. ... Update: Added version 1.1 that makes the camera mount slide on the the printer arm much tighter and fits...

... the right side. For right side optional drawer see: https://www.thingiverse.com/thing:5138213 or https://www.thingiverse.com/thing:5138213 It's my first remix ever, so any suggestions are welcome. Printed and fitted on my Ender 3 V2 Neo.

Remix of this to fit a Pi 5's slightly different IO. My modelling skills are weak, tolerances could be better, etc etc. ...But it works.

Also added cutout for USB passthrough on front of the draw Pi runs at about 45c while printing (No heatsinks installed) Hole spacing for LM2596 used are 58mm x 32.5 Hardware required 8 piece M3x6mm (Pi and Converter can use 2 each if you haven't got...

I didn't put a fan in the design because I have modded the original 40mm controller fan with a 80mm fan, it pushes a lot of air through the vents, should also be able to cool down the Pi. Fan Mods I used: ...

ENDER 3 V2 Raspberry Pi 4 Case Notes: this case is designed to hold a Raspberry Pi 4,2 30mm fans and 2 Buck Converters I'm intending to use the Arduino to prototype some different/unusual sensor integrations to the Printer print Settings: nozzle...

Its just a small remix with a 60mm top fan that i had in a drawer. ... I've updated the tittle because it's fitting a RPI 1 B+ too.

Remixed the Lid since I do not need access to the GPIO Header. ...and a Fan wasn't needed in my case

<p>I have re-mixed this part to include a hole for the feed wire to the LM2596 in the back of the case, also increased the length of the LM2596 mounting holes as the smallest M3 screws i have where too long, also notched the two nounting pillars by...

This project was designed and built using Tinkercad's powerful online editing tool, accessible here - https://www.tinkercad.com/things/2uZEKkvDujs.

I've revamped this part to include an opening for the feed wire that connects directly to the LM2596 at the rear of the enclosure. Additionally, I've lengthened the LM2596 mounting holes as the smallest M3 screws I had on hand were too long to use.

This adapter bridges the airbox to a Mikuni TM36 carburetor, which boasts a smaller intake diameter.\r\nThe stock "96 carburetor on the Honda 400XR leaves much to be desired, and upgrading is a game-changer for the bike's performance. ...This part was...

I uninstalled the rail so I could install it on a different printer. ...Big thanks to giacomo30196 for coming up with the original concept.

This design is inspired by giacomo30196's https://www.thingiverse.com/thing:3016364. A two-rail design makes the case more stably attached to the Ender3 frame. The slide-in cover locates at the bottom, avoiding screws altogether. We publish our work...

There is hole under display for USB port and SD card reader that I've cut out since I'm using different board and display that still fits under original cover. ...Printed from PETG.

I bought some lenses from Amazon and wanted to get a better angle for my OctoPrint timelapses. This added the M3 bolt holder from the camera back of one design and added to another design. ... ## Things you need to print: * camera_back.stl from my...

I made a tweak to the bottom part so that the inside doesn't have all those lines showing. It's a small change, but figured I'd share it with you. I didn't include the original files because [ender1968](https://www.thingiverse.com/ender1968) might...

I've changed extrusion to full for printing on side. Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil...

Remix of this item [https://www.thingiverse.com/thing:3256773](https://www.thingiverse.com/thing:3256773).\r\nEverything stays exactly the same except I scaled down the fan to fit my 25mm fan.\r\n\r\nI'm ignoring the missing screw for now, its...

This custom creation boasts a unique blend of style and functionality, featuring a sleek new cover and a sturdy fan mount that adds to its overall appeal. To enhance the user experience, I've also designed a spacious drawer with an improved handle...

For cura user scale it down to 10%

I want a Raspberry Pi 3 B housing combined with a camera mount. To achieve this, I merged both designs together. The housing is securely attached to the aluminum profile of my printer on the left side. Additionally, I want to monitor my printing...

Remix of [Ender 3 Pi 3 Sleeve Case RMX](https://www.thingiverse.com/thing:3546004), [Raspberry Pi case with Pi Camera for CR-10](https://www.thingiverse.com/thing:3079477), and [Ender 3 Sleeve Case RMX - Pi-Cam...

Updated front cover for the original lid over the Raspberry Pi to add a cool air intake.

Updated front cover for the original lid over the Raspberry Pi to add a cool air intake.

I created this custom Raspberry Pi 3 mount for my Ender 3, as I preferred not to use screws and wanted a designated hole for the RasPi Camera. This design is a remix of https://www.thingiverse.com/thing:2889371 The box slides effortlessly into the...