ender 3 s1 handle 3d models

MADE THESE TO STOP MY ENDER 5 S FROM ROCKING ALL OVER THE PLACE AT HIGH SPEED AND ACCEL RATES. WORKS AMAZING. ...COULD BE USE FOR ANY MACHINE WITH 20X20 OR 20X40 EXTRUSIONS.

swivel arm mount for sonic pad on Ender 5s1.most parts printed out of PLA+, the machine mount broke so i printed it out of ABS and added a corner radius, so it may work with pla.you need 2 m3 T-nut and M3x8 bolts. you need to put the T-nuts in the...

This bracket will help reduce glare and allow better visibility from a standing or seated position.

This is a Remix from the V3 version from Aiirik, but I replaced the mount for the V2 Version. Worked very nice for me. ...

Mirrored the original mount and added a cut out so it can mount on the left side.Also extended out the camera mount points so the camera can be mounted below if required.

My first post !

My ribbon holder's screw holes had cracked because I had overtightened the M2.5 screws. I couldn't see why I should not continue to use the https://www.thingiverse.com/thing:5404277 and so I've remade the adapter from...

This is a remix of the original design by PH1933. I just added a countersunk hole to secure it better. ... You will need: M3*12 bolt M3 T-Nut Printed with CHEP Cura 5 Extra Fast Profile with 20% infill

I could not find a good enough webcam mount for either my webcam or the printer I am using so I made my own. it mounts on the right side of the printer head bar. ...There is also a hole for a screw in the print just if you would need to secure it more...

This remix makes room for a 48mm Y axis stepper motor.   I did test print it at 5mm thick with ASA and it worked, but tigtening the bedscrews will bend the corners upward.  It needs to be made out of aluminum. ...  I used https://sendcutsend.com/ to...

This is a left front mount for a Creality Camera that works with the Creality Box 2.0 . I have not tested it yet I will upload pictures as soon as I have printed and tested it. UPDATE : Print the bolt part in 100% infill as it breaks off...

I made this after changing my filament support mount. ...so it's a simple mounting point that fits the extruded metal and sits nice and centre

A holder for the flat cable that keeps it in its natural shape, reduces the strain on the Х motor cables. ...No screws or tools needed.

<p>This is a quick and dirty fan duct that allows a 40mm Noctua fan to actually cool extruded filament as opposed to numerous designs with undersized outlets. Its not the prettiest thing but I managed to get better performance than the stock part fan...

Someone wanted this scraper with a cutter built in.

Remixed from the below model. Fits without hardware, just clip it on. https://www.printables.com/model/403964 Thanks to JLOJ, the original designer. ... Original model at thangs.com: https://social.thangs.com/m/853250

This is mix of https://www.thingiverse.com/thing:5761256 for single 5015 fan. It has 2 separate parts. Should be printed almost without supports (like shown in picture). I have fasten two parts by self-tapping screws. Just because I have no...

Print layer height a .2 on printer to test first layer

Customized version of https://www.thingiverse.com/thing:1949142 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1949142

I dont like the original position of the screen. So i designed this bracket to put it in a better position. The adapter was hold by the two original screws of the case (red circles). It fits a little bit strong but no problem to instal. Enjoy...

Combined the adapter from the filament spool spinner and the ship's wheel design. I'm new to manipulating 3d meshes in Fusion 360 so I'm not sure if the two objects were combined in the proper way, but this part does not need much structural...

Read the print notes! I dont like the original position of the screen so i designed this bracket to put it in a better position. It was holding by the two original screws from the case (red circles). It fits a little bit strong but no problem to...

My Stock Flat Cable Holder broke.... So I made a new one wich replaces the original one. I made it of 2 parts for easy printing. Assembled without additional material. For protecting the flat cable i also put some stripes of duct tape to it...

My cable eventually got damaged and I had to replace it. My solution to avoid it happening again is to bring the ribbon cable to the front and use this bracket. Print as my screenshot, with support, to increase strength. USE 2 x M3 nuts and...

Customized version of https://www.thingiverse.com/thing:34558 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=34558

I put the Ulanzi VL49 light on the printer to stream the print over night. So i dont have to use the big light all night. I think you can fit any other part there with the same connector. ...Maybe a camera or something.

I designed this bracket to relocate the filament run out sensor to the middle so the angle of the filament is centred when having 2 spools fitted. ...Print on its side to avoid layers from separating.