ender 3 s1 handle 3d models

As the Spatula doesn't fit in my tray in the printer and I wanted to have it accessible I printed the holder by irrational0. Now I rearranged my printer and had no room to use the holder, but needed it to mount on the left side of my printer.Easy...

Made a remix to an existing holder. Moved the length of the cable lock behind the motor. ...I made the opening a little wider to fit the screw washer that is added by the kit.

This model is designed to fit the extruder in one piece. It is an experimental design but it works perfectly. Then I will release a new version. Print fan side down. ... layer: 0.20 infill: 10% supports: yes

I really liked the original design, but I wanted to have it without the logo.

This filament sensor mount is smaller than my previous design, restricting the movement of the sensor. ... Requires an m3 threaded insert to be inserted into the mounting whole.

this is an alternativ to the heatbed cable chain many are using just use TPU, no supports required

OP's chains work great however, I noticed some binding near the extruder attachment. ...I used 5 modified chains to reduce binding and increase flexibility in some positions.

Idea came from https://www.thingiverse.com/thing:5444181 but I found the clip too narrow for the cable so made a new clip with more allowances from scratch that fits much better. Print it in the same orientation as in the images, not as it comes...

I remixed Nandomeier's design so the clip is on the other side of the Z-axis guide, this way it lines up with where my cable comes out from under the printer.

Remix I made to fit my Tapo C100 in the mount.

I tried some of the FAN ducts, but was never satisfied, so drew one myself. The Fusion360 file is attached. The FAN duct is as close to the original as possible, but has a little more distance to the hotbed. The design has no corners, so the air...

This is a quick and dirty fan duct that allows a 40mm Noctua fan to effectively cool extruded filament. It is not the prettiest thing but I managed to get better performance than the stock part fan using 100% fan speed and a resistor to lower the...

Remixed from alpo16000's sensor holder with added clips to secure the mount in place. I have left the bolts exposed on top as it was easier to remove the top rail and fit the mount and rail as one, slotting onto the upright. I have moved the plug...

I wasn't happy with the touch screen being the widest point of my printer, so I designed this to move it inboard and save some room. It prints in two pieces and snaps together, no supports required. It's a pretty good friction fit so no glue...

This is a remix of https://www.thingiverse.com/thing:5254088 I had some trouble getting Surnds0und's design off my print bed without it becoming deformed, so I made the whole design thicker (opposite of what they were going for) and added fillets...

This end cap replaces the one supplied, and allows both standard size spools and small spools to be slid onto the shaft without dismantling the end cap

Combination for holder and chain.

Why? ---- Since I'm no longer using the Creatlity firmware and run Klipper instead, on this Fujitsu Futro S740, I demounted the default screen and use the spot for the mini-PC instead. This is a simple mounting bracket that uses the holes and...

Torre modificada para PRUSA Slicer, la cargue con un perfil de 0.24 un poco mas acelerado de lo normal que me dio muy buenos resultados, el proyecyo que les comparto ya tiene los cambios de temperatura cargados. Saludos! ...

The light is Amazon: https://www.amazon.com/dp/B08VDH1GJV

The upper cable holder is remixed from romk's design ( https://www.thingiverse.com/thing:5423068 ). The lower cable holder is remixed from Sshelb8's design ( https://www.thingiverse.com/thing:6176160 ). ...Together, the two hold the extruder cable...

Just a remix where I made the design watertight. ...All other design aspects are from the original creator.

A basic mount designed to work with( https://www.amazon.com/Meggsi-Hygrometer-Thermometer-Temperature-Greenhouse/dp/B07W9LRV4K/ref=sr_1_1?crid=38ATJFT4G8C4W&keywords=b07w9lrv4k&qid=1661126353&sprefix=b07w9lrv4k%2Caps%2C131&sr=8-1) For checking temp...

<p>Read the print notes!</p><p>I dont like the original position of the screen so i designed this bracket to put it in a better position.<br>It was holding by the two original screws from the case (red circles).<br>It fits a little bit strong but no...

Useful in case you don't want to use the delivered spool holder (where the filament sensor is to be mounted). ...For best results rotate to its side before printing.

<p>Guides à coller au double face sous votre plateau afin de placer correctement et rapidement votre plaque PEI.</p><p>S'adapte surement à un grand nombre d'imprimantes.</p><p>Je les ai placés seulement à l'arrière du lit pour donner la position mais...

This is a remix of the project from here https://www.thingiverse.com/thing:5767800 by bensoneh. The issue with the original thingy was that the display mount was too close to the pi case so the top cover would not fit. Also the screw holes seems...

<p>Like the original supplied, my model has an end-stop in the flange to prevent it from falling off due to turning too far.<br>I have completely redesigned this holder, which has allowed me to create different lengths and refine the mesh...