ender 3 s1 plus upgrades 3d models

I have customised the model https://www.thingiverse.com/thing:5264357 to fit better with generic ender 3 S1 accessories / clipper and scraper. ... This is just raw edit made in IdeaMaker with boolean feature, but works just fine.

Clock dial indicator holder for Ender 3 S1's sprite extruder. Clips on over the heatblock Fan cover. ... Remove after use as it covers parts of the fan intake.

This is cable chain for Ender 3 s1 3D printer. You are need print 15 chain link and glue the two parts of the top. ... The bottom is attached to the profile, the top is attached to the roller bolt.

A filament pulley attachment to the Ender 3 S1 to interface with a [dry box](https://www.thingiverse.com/thing:4792927). ... Needs one [bearing](https://www.amazon.de/dp/B08K936Y1Z?psc=1&ref=ppx_yo2ov_dt_b_product_details).

This is a tool Tray for the Ender 3 S1 drawer. ...Includes individual compartments for each tool type, USB thumb drive, and a compartment with a sloped ramp to hold the SD card.

This is a tool keeper tray for the Ender 3 S1. Slides into the existing drawer for a tight fit. ... I left some front-to-back spacing to allow for removal when needed.

This is a remix of the mount for HugoHuge's "filler" filament roller. ...I made it to fit the stock spool holder arm for the Ender 3 S1. ...I printed it at 30% infill with tree supports.

I have customised the model https://www.thingiverse.com/thing:5264357 to fit better with generic ender 3 S1 accessories / clipper and scraper. ... This is just raw edit made in IdeaMaker with boolean feature, but works just fine.

Cover for the Ender 3 S1 LCD Screen. Keeps dust off and protects against scratches, or Loki's anger. ... https://www.prusaprinters.org/social/223023-three-nippled-goldfish/prints

This is a snap on fit tool holder for the Ender 3 S1 and S1 Pro. Small portion requires supports, see image for details. It holds all the tools that come with an Ender 3 S1 and a few extras too. All tools are held away from the gantry so they don't...

Some have adapted it for the Ender 3 V2 but the CR-Touch support part touches the pulley cover before making contact with the limit switch. For example, you'd need to add a screw to the top of the CR-Touch through the plate to make contact with the...

This is a remix of Ender 3 S1 CableGuide. This clamp holds the ribbon cable in place close to the printer just above where it exits the base. It bolts to the Z-axis frame using a bolt and nut provided in the spare parts that should have come with...

This is a mount designed for use of the 12-inch Hyper Tough led under cabinet light, specifically designed for use on the ender s1 but will work on all ender 3 models and may work on other models as well

This is a remix of the dual axis ender 3 tool holder to allow it to fit on the Ender 3 S1. I used the insert from the filament guide as a connecting base and made some adjustments to the tab length, and attached it to a widened out version of the...

left side tool bin for ender 3 s1 pro for starter tools attaches at left cornerThis object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/gQVsGDOCnaI

The corner on the Ender 3 S1 differs from the Ender 3 S1 Pro model and has a very different design over the pro model. If you mirror it you should get a right corner. The tear shaped holes indicate which way is up. There are two variations. A...

3D printer filament guide specifically for the Ender 3 S1. For a dehydrator at the same level as your 3D printer. It guides the filament from and to the filament senor to the extruder. I used ABS for a stronger print. Sanded the hole a little to make...

Just a quick model i threw together to tidy up the drawer on my Ender 3 S1. Slot for flush cutters made to fit my Knipex model ones but the cheap ones you get with the printer also fit. ... No base for faster print and less filament

Remixed this from an Ender 3 Pro LED Light bar holder by scottyujan. I just found it to be too short for the LED light bar I had kicking around. Extended the ends to support my 30CM bar. ...Tucks neatly under the S1 filament runout sensor.

Simple arrow for the motor on the extruder of an Ender 3 S1 Designed to friction fitI till be a bit tight thats by design as you can shave down the inside a bit depending on the fit you want

A remix of the Squat0001's bedlock, which feet better to the Ender 3 S1 I have printed it in PETG (for better resistance than PLA) with supports (didn't tried without supports) Edit 26/05/2023 : I uploaded a V3 with a better Lock capacity

Optimized fan duct for ender 3 S1 allows to fix fans of 40x40mm height 10 or 20mm in 24V (so you can connect it directly to the board) The duct is designed in such a way that the entire flow is concentrated on the nozzle

... ...Now thicker base sround the Dial stem, And can secure Dialindicator with a 3mm screw. Clips on over heatblock fan cover, should be removed after use as it covers part of the fan intake.Printed in PLA+ 20% infill on a Ender 3 S1 Pro

A simple but effective webcam mount designed specifically for the Ender-3 S1. Simply slides on to the X gantry, no tools or disassembly required. V2 changes: added cable tie holes. Also included is a threaded knob to match any webcam with a...

cable clamp for 3 S1, avoids pulling out the motor wires and end of stroke sensor.

A remix of AJCam44's excellent cable support for Ender 3 S1 Pro. I adapted it to fit the S1 non pro. Also I added support for extra wiring shown in the photos. Should work with PLA but I used PETG. The bottom support bracket is very different...

Remix of Diogosantos88's Drag Chain - Cable Chain - Ender 3 Still Work in Progress Main Chain is DoneBest way to attach the Under_Printer_Clip is to look for the wide gap where the cable exits the printer > Put in one end of the print...

If you have an Ender-3 S1 you know the drawer is very useful, but it can get messy real quick. This organizer helps making a better use of it.You can print in PLA, PETG, etc with 1 or 2 walls, any infill % as long as you have 3 top & bottom layers.

Improved design of another drawer system.Next variation will have nozzle storage incorporated.Width: 118.50mmLength: 160.00mmDepth: 16.15mmIf you like this please consider buying me a coffee: https://www.buymeacoffee.com/missionrea9 Edit: added...

*update* Added the f3d file for those who want to improve fitting ******************************* This is my first attempt to design a simple dust cover for my recently bought Ender 3 S1. There's a bit of play in my design and does not fit snuggly in...