ender 3 v2 direct drive with bltouch by5 3d models

Filament Sensor: BigTreeTech Filament Break Detection Module For 1.75mm https://www.aliexpress.com/item/33028816768.html

Spacer for the BLTouch Mount on the TriangleLabs Direct Drive Extruder Kit. The Springs Are Not Required, as a 4mm Spacer Is Sufficient. ...The Real BLTouch Has a Z Probe Offset of Approximately 2mm.

Hi, I made this bracket for the Neptune 3 if you already has set a Direct drive on it. ...you will need:4x 4mm screw by 16mm tall with the same nuts use for the spool holder.Will need an extension cable for the filament sensor roughly around 35cm.

This is a remix of the Satsana Ender 3 Fan Duct that makes it where you can use the free completely printed direct drive I designed and the BL-touch. THIS ONLY WORKS IF YOU HAVE A TOO LONG HOTEND like this one from Amazon:...

*30.05.2021 I replaced the files with updated version:* - Thicker backplate (2mm -> 3mm) - Thicker heatsink hilder - Two holes in the wire hilder plate for convenient cable tie use This is a single piece adapter to upgrade your Creality CR-10 or...

I designed this part to fit the voron 2.2 quick change toolhead to my ender 3 v2, I made one with a bltouch mount placed behind the hotend . ... BLTOUCH VERSION - M3 Threaded Inserts X3 - M3 Nuts X2 - M3 x 15 Screws X4 NON BLTOUCH VERSION - M3 Threaded...

Ender 5 PLUS One 400mm top one 400mm bottom rails with two MGN9C carriages. Tool included to line up rail. If you buy the cheap ones make sure you inspect and clean your carriages before installing, info available online from many sources. ... Y limit...

I also added some clearance for BLTouch and moved everything over just a little for improved alignment from my BMG All Metal Clone to the stock hot end. I also added a little more support to make it a little stiffer without restricting airflow to...

This is a mix of the direct drive mount from paydayxray (https://www.thingiverse.com/thing:4310609) and the hot end side link from Gnizten (https://www.thingiverse.com/thing:4116655)

Compwizard's Direct Design BLTouch Sensor Holder Works Perfectly for Me in Rev 2, While Rev 3 Offers a 2mm Higher Sensor Adjustment Capability.

Sensor mount for the Creality Sonic Pad that mounts on the right side of the Micro Swiss Direct Drive plate. Pretty easy to put on and take off. ...A few small zip ties secures the sensor to the bracket, then screw to the plate and calibrate.

This modification makes the part taller and allows you to mount the parts higher up using 3 screws, then slowly lower them as you tighten the PTFE connector. It is particularly useful when frequently changing tubing or ends, but it may not be...

Ender 3 v2 ABL + BLTouch mounts MinionD Ender 3 / PRO / v2 dual ducthttps://www.thingiverse.com/thing:4819097 Velocity Stack for MinionD dual ducthttps://www.thingiverse.com/thing:4861232 As requested for the Ender 3 v2:08/06/2021 - ABL + BLTouch...

After installing the MicroSwiss all metal hotend and direct drive system the cables kept hitting the extruder and the filament lever. So I designed this cable guide that has an arm that rests on the extruder body and can be secured with an M3 x 15...

Update: A version compatible with the Creality BL Touch mount has been included. If you're using a custom BL Touch mount, just print the regular version. Update 2: The X Axis Cable Chain Mount has also been added. ...To secure it in place, use some...

I've printed and set up a BMG clone with V6 hotend, paired with a pancake stepper motor. This mount allows ABL mounts to secure on the left side without any issues. EZABL 18mm fits perfectly with an offset of -48, -10. ...If you have BLT or EZABL, it...

**Update July 4th 6PM PDT:** All 'no chain' versions now support both Ender 3 series and Ender 5 series printers with updated files HMG5_DD_mount_Ende3-r5_No_chain.stl and HMG5_Dual_Gear_DD_mount_Ender3-5_No_chain.stl. **Update July 4th 5:15PM...

Update July 4th 6PM PDT: Updated the 'no chain versions to support both Ender 3 series and Ender 5 series printers. HMG5_DD_mount_Ende3-r5_No_chain.stl HMG5_Dual_Gear_DD_mount_Ender3-5_No_chain.stl Update July 4th 5:15PM PDT: Updated all files to...

Print instructionsUnassociated tags: Hero Me Category: 3D Printer Parts Summary Update July 4th 6PM PDT: Updated the 'no chain versions to support both Ender 3 series and Ender 5 series printers. HMG5_DD_mount_Ende3-r5_No_chain.stl ...

The Direct Drive Kit E3D V6 -Bondtech (right) -Pancake comes with two sturdy supports, one designed for 25mm Pancakes and another for 28mm Pancakes. An adjustable BLTouch holder is included, along with a straight ventilation nozzle that's fully...

The Direct Drive Kit E3D v6 - Bondtech (right) - Pancake is comprised of two bases, one for the Pancake 25mm and one for the Pancake 28 mm. A adjustable Bltouch support and a straight ventilation nozzle for the 5015 are also included. On the bases,...

The Ender 5 plus's location on this design smacks the Bl touch on the Z rails when homing, moving it out of the way but still requiring offset changes to avoid hitting the left-hand side Z rods. ...I adjusted these offsets in the starting gcode within...

This updated version reinforced the motor mount wall and added extra support, along with a cable management tower to keep things tidy. This revised version is what I now use. I took my original and rotated the stepper motor and BMG mount 90 degrees....

For the assembly, I used the original detector's screws of the Ender 5. Be careful, the holes are deliberately narrow, so you have to use an M3 tap, otherwise you have to pass once an original screw "in force" to create the tapping allowing the...

original sharpie blender https://www.myminifactory.com/object/3d-print-sharpie-marker-color-blender-3d-print-custom-colors-and-gradients-3-and-6-marker-version-138353

This is conformed to work with the bullseye and the Santansa fan assemblies. I added a cable rest because my cable was just hanging down and being drug around. Gotta take care of the special parts. ...:)

I crafted theneedful's rendition with impressive results, but I felt it could benefit from additional reinforcement. So, I created my remix, aiming to provide even more robust support. ...To achieve this, I added extra support structures on either side...

The one that Direct Drive CR-10S direct from Bondtech offered was about 6 MM short and caused it to bend out so I added spacer nuts at first but I wanted something more stable so this is my remix to correct that without adding much but giving it some...

It worked to me now, but maybe I will update it later with only 9mm extension. I think 10mm is a little to long now (but it works). Update: Aded new file, not printed yet. 9mm offset in X (instead 10mm in first file) and 0,5mm offset also in Y (zero...