ender 3 v2 direct drive with bltouch by5 3d models

... to fit the satsana 4010 bltouch found here https://www.thingiverse.com/thing:4637453. ... i moved the cable chain mount 25mm to the side to match the wiring placement on the satsana 4010 bltouch (stock fans) fitted, tested and works great!

... it. BLTouch mount (by RENOxDECEPTION) added on remixed SATSANA duct (by SeanChangX) for E3V2. -54,-6 is the probe offset. ABS recommended for resisting hot temp. ... Thanks for original SATSANA creator, SeanChangX and RENOxDECEPTION

Utilizing the remaining components from the original designer's creation: http://www.thingiverse.com/thing:1745276 The DiiCooler model used in this remix is available here: http://www.thingiverse.com/thing:1025471, specifically designed for the...

I needed a direct drive mount for my ender 5 and titan extruder could find one I liked so made one. ...uses original screws and fan and covers this is version 2 added strain relief Added spacer for grater Z offset of BLTouch but mine was - without...

This is remix that fixes the location of the cooling outlets to work with Spider 500c hot end.

I create this support to adapt my BLtouch in Sprite Pro Ender 3 I just use 4 M3 x 15 bolts and 2 nuts

Fits the BLTouch and 3DTouch for Ender 3 or Ender 3 PRO Special features -The Extruder Fan Cover can be removed independently (no need to also remove the BLTouch mount), thus not messing up the probe Z offset -Optimized cable placement. -Small and...

I run *10* of my printers in my small printer farm (Ender 3 DualZ, Ender 3 BLV and Ender 5 Pluses) with this standardized BMG Fan mounts. UPDATE: Uploaded a beefier fan mount for both the standard V6 and volcano version. Uploaded BMG mount for...

This is a remix of Bart-tech3D's Ender 3 Direct Drive Extruder. It's a very simple remix that removes a 2mm section of the model to allow the metal Creality BLTouch mount to be used. The BL touch mount will fill in the removed area of the stepper...

I ended up having to redesign the mounting plate that also holds the BLtouch, had to drop the BLtouch mount so it sits closer to the bed and I also had to stretch out the FANG as the hot end sits about 10 mm lower than previous hot ends. ...The duct for...

Direct Drive Ender 5 MGN Linear Guide Upgrade Kit - Elevate Your 3D Printing Experience

This version has roughly 5 mm sheared from the top to allow for better clearance with my direct drive setup. The holes were aligned and sized using the f3d model of the Ender 3 provided by Creality.Offsets are [X:-43.6, Y: -5.8]. ...My Z offset is -2.4,...

This is a remix of MrHasBean's Direct Drive mod but with additional space to accommodate the Creality style dual gear extruders. I also added the ADXL mount from shiang91221 onto the front for anyone utilizing it for input shaping. This can be a...

by placing the mount for the BL touch to the right side the cable management was a lot nicer

Remix from Satsana/Juanolo, added GoPro Mount and Holder for LED-Strip

It includes a new extruder orientation, a mount for a BLTouch and for a 5015 radial fan. The parts should be printed in a heat resistant material like Nylon or similar. PETG might be okay as well. For installing the Hemera, look at the E3D...

I was using https://www.thingiverse.com/thing:4742800 with stock ender 3 v2 but upgraded to Micro Swiss direct-drive and hot-end. I wanted to reuse the endoscope holder I had already and just mount it to this fan shroud. ... This endoscope is hooked...

For Hypercube Evolution New X-Carrier Car with Integrated Optical Endstops NEW Part Cooling Fan, Adjustable Added Mounting Plate for E3D Titan https://e3d-online.com/titan-extruder E3D Hotend Lite https://e3d-online.com/lite6 BL-Touch...

Check out this upgraded aluminum dual-gear pulley dual-drive extruder kit compatible with Creality's CR-10, CR-10S, and CR-10S Pro 3D printers, as well as Ender 3 and Ender 3 Pro models:...

I purchased a Haldis extruder only to find out it isn't compatible with any direct drive plates for the Ender 5+, on Thingiverse. ... I turned the extruder 90 degrees to allow for the spring tension bolt to be accessible.

It includes a new extruder orientation, a mount for a BLTouch and for a 5015 radial fan. The parts should be printed in a heat resistant material like Nylon or similar. PETG might be okay as well. For installing the Hemera, look at the E3D...

Remix of Increased_Wheel_Clearance_Dual_Geared_Extruder_Direct_Drive_Side_Mount_for_Creality_BLTouch_Mount_Users To add a mounting hole for an M8 Pneumatic Bowden tube fitting. ...This should allow for better filament guidance into the extruder.

This is the reboot of two incredible endeavors, merging the genius of two outstanding projects:\r\nhttps://www.thingiverse.com/thing:3078853\r\nhttps://www.thingiverse.com/thing:3586698\r\n\r\nI've seamlessly integrated them and introduced a BLTouch...

http://creativecommons.org/licenses/by/3.0/ This remix solved the problem of the original 60mm fan cover not fitting with the pin27 board for the BLTOUCH installed. I took the original cover, shifted the whole 'hump' about 15mm backwards and...

CR10 - TİTAN DİRECT DRİVE

CR10 - TİTAN DİRECT DRİVE

Minimized Base to my needs on FolgerTech ft-5 v2 by remixing Note the file here is the black part in the images

This is just a remix for people who have Creality Bltouchs and adds a tiny bit more space to your bed. I basically took some length off of the main piece where the motor sits. I also cut a hole on the side of the hinge to allow for the x-axis front...

This is just a remix for people who have Creality Bltouchs and adds a tiny bit more space to your bed. I basically took some length off of the main piece where the motor sits. I also cut a hole on the side of the hinge to allow for the x-axis front...

This adapter enables direct drive configuration for my Ender 5. I had to design it myself because the dual gear upgrade alters where filament is extruded from. ...It was created specifically for my Ender 5, though it might also work with other Creality...