ender 3 v2 direct drive with bltouch by5 3d models

27/09/2020 Designed to fit the Rasp Pi 4 and display for Ender 3 V2 It will fit the lower versions of pi also. Print Settings Bottom: just print flat and will print fine Top: print upright with supports from build plate Cap: print flat 100% infill...

This is a hastily crafted adaptation of the hero me gen 2 tailored specifically for the mosquito hot end to be paired with a micro swiss direct drive extruder. Being entirely new to design, I relied on tinker cad to customize Mediaman's original...

... probe, so I had an endstop switch not in use. I remixed the Filament Roller Guide to add a support for the endstop switch and used as Filament Runout sensor. The endstop switch is from an Ender 3 V2, I don't know if it's the same for other Enders.

Simple remix taking the very nice side modified side spool holder and adding rail slots for the Ender 3/Pro/V2 2020 extrusions. I did this because I forgot I had 2 T-nuts from where the spool holder was mounted on the top of the frame that I...

The Ender 3 V2 Motion Sensor Bracket that came with the Sonic Pad was wobbly and i didnt trust it to give me proper vibration readings so I designed this as close to the original as possible but added a few support beams which greatly strengthened...

--------------------------------------Evian_Arts-------------------------------------- ''I had enough of the tools rattling each time i would open the drawer and getting all mixed up after i organised them.'' Drawer organiser for the Ender 3 V2:...

27/09/2020 Designed to fit the Rasp Pi 4 and display for Ender 3 V2 It will fit the lower versions of pi also. Print Settings Bottom: just print flat and will print fine Top: print upright with supports from build plate Cap: print flat 100% infill...

Ho progettato una montatura E3D V6 originale o clone simile al design della Voron ma con la guida diretta originale della Ender 3/5 o la versione in alluminio senza limitare le corse X e Y. ...Il tutto viene montato sulla piastra originale della ender...

Thinner mount in general, with integrated attachment for BLTouch sensor.

... Pinda probe mount inside the fan shroud. The Pinda probe will screw into the hole allowing you to make fine adjustments to dial in your offset. For instructions on connecting a Pinda instead of a BLTouch well that's out there somewhere. ...

This mount converts your Ender 5 into a direct drive printer, using Bondtech LGX Lite - Large Gear Extruder. The support replaces the original parts holding fans and the bed leveling sensor. Features increased airflow to the hot end's heatsink due...

Was thinking of mounting a Pi/Buck converter to the back of the Ender 3 V2, where the PSU in previous models used to be, to act as both a sleek(er) mount and a bracer to further stabilise the frame. I have already created a Pi case using this idea,...

It goes a long way in helping me grow my channel and content! You can find the BLtouch/CRtouch firmware for the Ender 7 here:► https://embracemaking.com/products/creality-ender-7-bondtech-lgx-lite-mosquito-magnum-hot-end-kitScroll to the bottom...

The benefits of CoreXY system is that your ender 3 v2 doesn’t have to move the heavy glass plate anymore, so by addressing this issue now you can start to increase the printing speed with less impact on print quality. build volume of 220 x 220 x...

This base plate can be re-used for other direct drive systems (Sherpa Mini etc.) Just need to design one for your new extruder and try it out :) For the BMG only one spacer is needed for the top screw This design allows to fit many type of cooling...

A lightweight, unobtrusive, and simplistic drive drive mount for any stepper using the Winsinn Dual Gear Extruder. Confirmed to be non-obstructive with duct designs such as Hero Me, Petsfang, and Hydra. I personally use this mount with a 34mm Nema...

I decided that I liked the Dual Geared Extruder style Direct Drive plate by paydayxray and I liked the cable relief bracket by BGDog. Both couldnt be used at the same time, so I decided to remix them into one mounting bracket. ... Original files are: ...

This is a combination of NLAIV's direct drive mount and  Pryies's Fetsfand Bullseye Base remix (both of these are listed as base-parts-*).   The dual gear model is the one shown in the photo. ...It has a 9mm offset to allow the filiment path to be...

My setup is weird. ...So I needed a specific mount to make my printer Direct Drive. If I'm not the only one, here's the file. ... The Updated V7 File includes a slight adjustment to the motor placement to account for variations in HeroMe spacing.

Anycubic Chiron - BMG Bondtech Direct drive mirrored - support - BLTouch - E3D V6 - turbo fan. There are precise holes for M2 screws spaced to size for the BLTouch sensor. Behind the turbo fan, there is a clear guide for inserting the cables of the...

This is a CAD model of the Ender 3-V2. This is the original modeling for the Ender 3V2 that is used by others and published on different sites. The measurements and modeling are made from my own Ender 3V2 3D printer which I love and it works like a...

For X axis you'll need 3 - M4x10 (with nuts) to fix to stock Ender 5 metal plate. 4 - M3x10 to fix to linear rail block. For this mod I used 3 - 450mm linear rails with MGN12 block. X_Carriage MGN12_Block.stl - to be printed in PETG because...

Side arms have been lengthened to avoid collisions with the extrusion nozzle of the ender 3 version 2 printer and swivel support has been added to the base of the camera

This is a remix I made of a C270 webcam mount for the ender 3 V2I lowered the webcam down to give clearance for a CR Touch. This position gives a better view of the print to check for spaghetti but less of a “top down” overview.</p><p>This model...

The original I remixed didn't quite fit my direct drive extruder, and I wanted it open on the front to aid feeding filament. This remix checks all the boxes I needed. I cut down the cable guide on the side a bit so that it would fit my extruder...

Redesigned this to fit a Creality CR10S Pro V2 with a Micro Swiss hot end and direct drive. Used supports on build plate only. ... Updated with correct duct, and no longer need to resize.

Assemble: - put two M3 nuts in the bottom of the mount - attach mount to the printer's frame with 4 M3 bolts - mount runout sensor If you have M6 PTFE tube holder from extruder screw it from from the output side of the mount. If you have not you can...

This is a simple adapter for BLTouch on "Tronxy X5sa BMG Direct Drive/V6/Volcano Mod". This is an untested revision, the previous iteration was printed and tested but a slight error was found which has been corrected in this one but I have not been...

This is a two-part system for mounting a Bondtech BMG extruder or clones directly onto a stock Ender 5 mount without reducing any printing space. The mount is compatible with the HeroMe Gen3 Fan Duct and Mount, E3D volcano Hotends, Stock Hotends,...

And I got pretty close Features: - Works with the Ender 3 - Compatible with the Hero Me duct - Positioned above the hotend for a straight path from extruder to hotend - Best used with a pancake motor for low weight - Many of the needed parts can be...