ender 3 v2 display 3d models

For designers to make custom print head and other mods for the X carriage assembly on the Ender 3 V2 Neo. Update 2-16-23 3PM PDT: Corrected the position of the upper left V-Wheel, was off by 4mm. Added a missing hole at the top right of center on...

Fast print for easier turning of the factory extruder wheel for the Ender 3 V2. Designed with blender. Snug fit for the recesses of the wheel without additional fixings. The head of the crank has a recess for quick turning with the fingertip. ...

... Used the Cable Chain Management from here. ...Cudo's for this. https://www.thingiverse.com/thing:4794723 Used the Cable Management from here. Cudo's for this! Perfect and Complete Cable Chain Management Setup For Your Ender 3 V2.

Hello, after a difficult job, I present the first Mistral Fan mod for Ender 3 V2! ... Very easy to install especially if you use my ratchet screwdriver ;-) https://www.thingiverse.com/thing:4853538 Plug ang play No modifications Recommended abs 20%...

Mounts to the M3 holes on the Ender 3 V2 X-carriage, with the same probe offset as the classic mount by Jkostenov. Fits with the stock fan duct as well as the Mini-Me V4. Probe offset: X-42.00 Y-10.00 Thanks to Jkostenov for creating the original,...

My PS Eye mount for Ender 3 v2. There is no need for screws. It slides right to the main 4040 profile of the base and the camera goes on the top of the mount. ...The camera base should slide right into the top of the mount and happily sit there.

... the way, so I made this. ...It is mountable on the Ender 3 V2, and I'm not sure about the pro. Definitely not the original, though. It is made for the raspberry pi 4b. ...Thanks to https://www.thingiverse.com/thing:4665097/ for making this originally!

Screen wire protect, use with ENDER 3 V2 LH SCREEN MOUNT_REMIX (https://cults3d.com/fr/mod%C3%A8le-3d/outil/ahuczekdesign-32ca). You have STL and Fusion360 file. You can change parameter in Fusion360 to change anything. Print face to bed, and use...

... en este, se mantienen dos ductos de salida y se puede usar con el cr touch instalado. ...Print Settings Printer Brand: Creality Printer: Ender-3 V2 Neo Resolution: 0.32 Infill: 10 Filament: no pla, petg Post-Printing Category: 3D Printer Accessories

Fits very tightly on the lower 40mmx40mm rails of the Ender 3 v2. Provides a "shelf" to support the wires and gives you something to tie wrap to. STL file contains left and right facing brackets. ... Print both or delete the one you don't need in...

Mounts to the M3 holes on the Ender 3 V2 X-carriage, with the same probe offset as the classic mount by Jkostenov. Fits with the stock fan duct as well as the Mini-Me V4. ... <strong>Probe offset: X-42.00 Y-10.00</strong> <strong>Thanks to...

I moved some of the holes to better fit my Ender 3 V2, and cleaned up some of the mesh. ...This should fit the Stealthburner as of commit aabd953 Updated Jan 9 2022 to fix hole location Stealthburner link: ...

Updated the mounting section with a boolean cut to accomodate the z-screw brass mount, which on the Ender 3 V2 is protruding of about 1mm. Also gave slightly more room for the z-screw itself. ... Added a second design, without the z-screw protection,...

Remixed By Mythical Now supports Ender 3 V2 Changes to the original - Leaves a small space at the back right of the part for the z axis cable that goes into the motor (see picture) Spaced back so the print is flush with the back of the z axis switch...

Bottom Filament Guide for Ender 3 V2 Neo. This is a remix of two designs taking the best element of each. https://www.thingiverse.com/thing:3010366 https://www.thingiverse.com/thing:4648991 PLA is strong enough. ... Carefully remove Z axis...

wire support for my ender 3 v2 direct drive, mounted to the top of the enclosure and use a auto retract keychain inside. ... https://www.amazon.co.uk/gp/product/B0995YK84C/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1 key chain used, just trim the...

If you have the Ender 3 v2 Adjustable Screen Holder or the remix, and your screen is loose, you don't have to reprint the entire thing again. Print 2 of these wedges and install then on the screen posts, behind the adjustable screen holder. ...If it...

I've designed an incredibly basic PSU holder specifically for my Lack table enclosure, which accommodates my Creality Ender 3 v2 Neo. It's crude and simple but it got the job done. The design allows for mounting the PSU under the table's top surface....

#### CR Touch Mount for the Satsana Remix for the Ender 3 V2 I couldn't find a remix for the CR-Touch so I created it myself. #### Why? ... Because the original mount didn't have room for the connector of the CR-Touch, and if you tried to put the...

Here is a remix of the Ender 3 V2 nozzle holder. 39 nozzles and a BL-Touch replacement tip can be stored in it. I removed the handle and adjusted the spacing. I also designed an organizer for screws and other small items. ...2 versions can be...

... but bltouch will be mounted 3mm higher. ... Original worked great with stock Ender 3 v2 hotend, but I replaced it with all-metal one which is slightly shorter for some reason and bltouch probe collided with bed.

This is a replacement drawer knob for the Ender 3 v2 drawer. I suggest to print in PETG since it is more flefible and PLA will break when you push it in the hole of the drawer. Category: 3D Printer Parts

Simple little part to cover the Ender 3 V2's Z screw - the filament passes past it very close and I didn't want filament to be hit by it. ... It fits over the brass bushing and there's little notches for the screws either side.

Made some slight adjustments to the hole placement to allow fitment onto the Ender 3 Pro V2 as the mounting plate is slightly different. I filled in the screw access hole that was on the front too. ... Simple screw into the bottom left (as...

Designed to fit Creality Ender 3 V2 Neo but can be used as standard container without attaching the rails. ... 2 container sizes (mm): 135L x 40W x 25H and 135L x 40W x 40H Caution: When used on printer, keep all items below build plate surface to...

Used the base of "Ender 3 v2 Spool Holder" by Pugwash" then just added a little platform for the cam to rest on. ...I tightened up the tolerances a bit to make the mount more secure so it ends up being a tight fit.

If you have direct drive and the extruder stepper space is empty, you can use this as a cable guide on your Ender 3 (v2). ... If your printer is inside an enclosure i advise to use heat resistant filaments like: ABS/ASA/PETG

Included is a ready-made gcode for Ender 3 V2 temp tower for PETG. E-Steps are set for my extruder, change line 21 in G-Code to your extruder's E-Steps.Comment out line 20 if you don't have BLTouch/CRTouch.

I combined this with a mount to attach it to my side rails on my Ender 3 v2. ... I installed it on the left side of my printer, you'll need to remove the 2 fronts (LARGE) screws and 1 screw at the bottom.

Ender 3 V2 better Motherboard Case This motherboard case has a sliding lid that is on the top of it, in this case there is enough room to fit the motherboard and two buck converters for noctua fans or anything if there is anything to update on the...