ender 3 v2 micro usb port 3d models

This adapter will fit for the Ender 3 Pro V2 Compact SD Card Adapter Housing V4 https://www.thingiverse.com/thing:4609997 I`ve designed this to fit a microsd extension in the sd slot. ...

Hobbled together something that will work to properly allow the NG extruder to hit the X-Axis limit switch on the Ender 3 V2 Neo from Creality. ...The switch style is that of the Ender 3 S-1 model which lays flat instead of vertical.

Love this design not just for the clean look, but also for the compact size and weight which is fairly important for direct drive setups.I have made changes to make it fit the Micro-Swiss Ender 3 direct drive hot end setup for my Ender 3 V2 since the...

Love this design not just for the clean look, but also for the compact size and weight which is fairly important for direct drive setups.I have made changes to make it fit the Micro-Swiss Ender 3 direct drive hot end setup for my Ender 3 V2 since the...

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/l6NpAdw8COm

This object originated from a design created using Tinkercad. ...You can modify it directly on their website at https://www.tinkercad.com/things/l6NpAdw8COm.

This prints helps protect the USB connector of your Ender 3 pro / Ender 3 V2. It uses the existing screws in the front of the machine. It is designed for a right angle connector. This is highly recommended when using a print server like octoprint...

The original plastic seems quite soft, and it broke. I repaired it with this part. Print instructionsI printed it in petg just to be sure. 3 perimeters 25% infill brim 0.4mm nozzle 0.2mm layer height

This is a simple design to be able to install the hot end fan and the part fan on a new Micro Swiss Direct Drive. Since the original hard ware will not fit the new part, here is a solution. ... Just change the parts Fan Nozzle 4 mm and centered with the...

USB panel for 3 port USB sockets

... This makes for a better mesh in my opinion and it just looks cool. 3. Designed a new mount for the BTT Smart Filament Sensor. 4. ...Redesigned the top hat to accommodate the wiring harness a bit better with the addition of all the extra stuff.

Halterung für ein 24V USB KFZ Netzteil zur Versorgung des RaspberryPi (OctoPi) und der Beleuchtung an der Führungsschiene des Ender 3 V2. ... ---- Bracket for a 24V USB car power supply to supply the RaspberryPi (OctoPi) and the lighting on the guide...

given the location of my ender 3 V2 and how i use it the usb cable and micro usb port were practically susceptible to damage either from accidental knocking or repeated use so i designed this to project the usb port and since note you will not be...

given the location of my ender 3 V2 and how i use it the usb cable and micro usb port were practically susceptible to damage either from accidental knocking or repeated use so i designed this to project the usb port and since note you will not be...

I think it's much improved over this one, you might want to try that one instead: https://cults3d.com/en/3d-model/tool/80mm-fan-psu-cover-for-ender-3-v2-aquila-with-usb-ports-no-supports ==============================================================...

This is a REMIX from BoothyBoothy the original version is here: https://www.thingiverse.com/thing:3517282 I printed this with taking for granted I purchased the correct Micro SD adapter but found out I purchased a different one from Amazon:...

A holder for the scraper, cutter, and USB drive that slides into the rails of the Ender 3 V2. Just a note, the fitment for the USB drive may be tight depending on the tolerances of your printer. For me, the USB drive has a snug fit so it doesn't...

* To add USB power ports to my Ender 3 v2 for my Raspberry Pi running Octoprint, and to power the USB LEDs surrounding the printer. The How: * Print each section as needed, and connect with the clips only, or secure with your preferred...

Slide-on USB stick holder for Creality Ender 3 V2. I have used the rail bracket similar to the one for the spatula: https://www.thingiverse.com/thing:3094723 It is not 100% tight fit, there is some wiggle to it because that's the way I wanted...

This is a remix from BoothyBoothy, the original version can be found here: https://www.thingiverse.com/thing:3517282 I printed this assuming I had purchased the correct Micro SD adapter but discovered that I had bought a different one from Amazon:...

English: A simple protection for the USB port and the SD card. In two versions (one with the Ender 3 logo and one without). The plate is simply attached to the printer with the screws that are already available. With the protection there is no...

English: A simple protection for the USB port and the SD card. In two versions (one with the Ender 3 logo and one without). The plate is simply attached to the printer with the screws that are already available. With the protection there is no...

Micro swiss direct drive extruder fan holder for ender 3, ender 3 pro and ender 3 v2 with x-axis correction. This is two part body (part no. 1 and part no. 2), after printing two body must stick together with plastic adhesive glue. This is because...

With a $3 part and some simple (but small) soldering, I now have a USBC port that works the same way as the MicroUSB port at the front of the printer. Actually, the port at the front of the printer still works - this mod doesn't disable it. I imagine...

remix this to fit top of my ender 3.

The original USB port cage had holes that were too small for my wire to fit through so I enlarged them. ... No other changes

In the process, I realized that I could remix this, protect the front USB port, and house the Raspberry Pi (Le Potatoe Pi in this case) in the front. The intention is to plug in all of the cables and then insert the Raspberry Pi into the case. If you...

Hello all, This is a MICRO version of the Ender 3, designed to create an "Inception" feeling by being even smaller than the Mini Version. No support needed for this print; you can do it in one part or multiple pieces. A square supporting the Y axis...

This is a modification of an existing Wyze cam v2 / Xiaomi Mijia Xiaofang 1S camera mount where I added a barrel-style USB hub for convenience. I sought a straightforward method to incorporate a USB hub that would turn on and off with the printer,...

Simple USB camera mount that clips easily onto the end of the X gantry of an Ender3 V2. The camera can be mounted above or below the gantry (watch out for bottoming on the control panel with larger cameras). Swings out of the way when not needed...