ender 3 v2 octopi 3d models

This is a remix of a good design, but I have added a diode (3 mm, red, 2V, 20 mA) with 510 ohm resistor powered by the same converter as the fan (12V) and the LED is in the eye of Ender dragon which I have added to the front face of this cover. I...

It's a snug fit but cannot fall out the other side because of the back stopper. I printed it at 10% infill at .2 resolution with 2mm thick walls I would recommend adding a support blocker on one side of the top to help you remove supports otherwise...

Made to fit Ender 3V2 but should fit any 20x20 extrusion. ... my need slight filing or sanding on posts as it is a pretty tight fit.

Soulsmith from the Will Wright Cradle Series. ...I Thought it would make a nifty badge for the ender 3v2, Remixed using Tinkercad.

This is a remix from https://www.thingiverse.com/thing:4756995 I just added the Ender Logo. ... Print vertical without supports

This is a remix from https://www.thingiverse.com/thing:4756995 I just added the Ender Logo. ... Print vertical without supports

Made to fit Ender 3V2 but should fit any 20x20 extrusion. ... my need slight filing or sanding on posts as it is a pretty tight fit.

Chopped off the piece to clip it into an ender frame, making it flat instead. Added two holes for screws. ...Can be used with an LACK enclosure etc.

I took over the project from x4runnerGunnerx : https://www.thingiverse.com/thing:4623647 I added the dragon Ender logo I hope you enjoy

measured it best I could and flipped it ~ and stretched it Printed and functional v3 because v1 wasn't long enough and v2 wasn't wide enough to fit the screen v3 is a little too wide but it is functional This is V3 I lost v1 and v2 wasn't worth the...

I tested PLA and ABS prints and in the end, I preferred PLA for robustness. The source code can be found here https://github.com/juandelacruz-calvo/360-octolapse-scriptsSimply clone the repository inside octopi and point the scripts to the folder in...

I only used this for tuning input shaper, then removed the mount.This model uses the space from here: BLTouch Spacer/Screw Cover for Ender 3 Pro by onpdm - ThingiverseI don't have a photo of it mounted, I'd removed it and started a new print by the...

Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Infill: 15% Notes: Printed with most of the flat side on the bed, a little support is needed to create the v-slot rails.The object should be orientated correct already...

Since I recently installed a BLTouch on my Ender 3 Pro, I no longer need the mechanical Z-axis end switch. I have now converted it into a filament runout sensor and designed a small housing for it. This one is a modification of my 1st version...

You do have to be careful not to tighten these screws because you will put stress on your leadscrew and cause printing issues. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 0.12 Infill: 10% Filament:...

(this is why there is a space near the SD card slot) Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: your choice Filament: Sunlu PETG/PLA/ABS any Notes: Fan mount is for a...

I am no expert on electronics, so I don't want to add a how to connect the cable to the 24v ender 3 power supply and ruin your printer section. I just connect the + - cables to the output and it magically works.. I added this...

I lengthened the mounting rod and changed the holder to work with the V2 Raspberry Pi camera. ... I also modified the [Twist in Cable Holder](https://www.thingiverse.com/thing:2816969) to work with the Raspberry Pi camera ribbon cable.

I've created a cover for the X-axis motor on the Ender3 v2 (to hide the QRcode). Feel free to ask if you want another design. ... No specific details for the parameters of the printer.

A guard over the PSU wire terminal . ... This is part of my attempt for better cable management of the Ender3 V2 https://www.thingiverse.com/thing:4761365 https://www.thingiverse.com/thing:4768402

This is a remix of the V2 version which has more clearance. The offset should be untouched X-43.65 Y-10. ...Added a cutout for the cable.</p>

Remixed the bottom connector from "Cable chains and connectors for Ender3 V2 - full set" by Beh01der. ...On the original part Y chain was connected too close to power switch and was not aligned with plate connector.

[DEPRECIATED] A new version is in the works with better accuracy measured it best I could and flipped it ~ and stretched it Printed and functional v3 because v1 wasn't long enough and v2 wasn't wide enough to fit the screen v3 is a little too wide...

It is just a tool holder for the Ender series but with a sliding mount instead of press-fit, and some SD/microSD card slots.Minimal supports needed, just for the sliders.

I needed the Ender 3V2 LCD to be on the left side to suit my desk setup, and wanted it "floating" to be able to move it late to be outside an enclosure (when I finally make one).

This is a bracket I designed that moves the screen from the right to the left side of the Ender 3v2. I printed with PLA 20% infill. ...Used ShapR3D software on iPad.

This is a filament spool adaptor for an Ender 3V2. ...Made to decrease the ID of the spool on the stock mount so the extruder motor has less resistance and vibrations.

reverse bowden to voron switchwire, specifically to the ender converted to voron switchwire, I couldn't find a corresponding file anywhere, so I created this one. In my case it helped with the zebra on prints. ...

This is a bracket I designed that moves the screen from the right to the left side of the Ender 3v2. I printed with PLA 20% infill. ...Used ShapR3D software on iPad.

This is an X-Axis mount made to fit the Ender 3V2 X axis arm/tensioner. ...I used it as a way to mount a camera for taking time lapses that moved up with the Z height.