ender 3 v2 octopi 3d models

This is a Remix of the knob COVER for the X / Y axis belt tensioner on your Ender 3v2 and others using the same OEM blue knob. The original was WAY TO TIGHT, so I made this one. Its larger in every way! ...

20% infill Nozzle: 0.4mm Layerheight: 0.2mm Support: no need only for the blower insert: Layerheight: 0.12mm Brim: inner 0.6mm Support: 1 small support block needed (see pictures) Reduced print speed recommended (very small piece) **My printing times...

V2 Shroud has holes for an intake guard to hold the fan in place. Also fits the blower fan better with retention clips. There is a tolerance issue with the backing plate and the shroud. They will lock together half way sliding it together. I...

This also allows you to tweak the angle of the camera to your liking on the mount since the Wyze Cam can move on its base.The Wyze mount point is not the full size of the Wyze Cam V2 base, and does not need to be (it is snug!) - this allows you to...

I had to modify the mount for the fan duct to work with the fan that was on my V2. I don't know if the fans are different between the original and V2. This model has been designed for SLA printing, but should be fine FDM printing. There is no...

The Wyze mount point is not the full size of the Wyze Cam V2 base, and does not need to be (it is snug!) - this allows you to print this much faster without support. You can slide the cam back and forth with a little force to put the camera closer...

This is a v2 of a remix I made, which should hopefully solve the potential problems of space, bl-touch compatibility, and different mounting situations for the raspberry pi. The old design had the chain running forward, which increases the space the...

... in the wire. There is a 10mm hole for the wire to pass through. For those of you who do not want to drill a hole in your OEM cover. This can be used with https://www.thingiverse.com/thing:5022636 when relocating the power switch on your Ender3_v2.

A simple clip to keep the wiring harness from falling out of the holder on the back of the extruder bracket on the Ender 3v2. My wiring harness keeps coming out of the standard holder (see second image) while printing, so I created this clip that...

I made v2 smaller to reduce surface area that touches the X rail. It dragged a bit too much, so I saw that adjustment was necessary to update the JPG picture. The belt tensioner is designed to hold its shape over time and not deform. It slides under...

This is a remix of https://www.thingiverse.com/thing:5179838This remix takes the mount the fits the Ender3 V2 hotend shroud and modifies it to fit a Mitutoyo 2046 dial indicator. ...The mount is a direct replacement for the rear cover of the...

... Version 2: The Housing has now the same high as the original one, so it can used on the original setup. File: "Y Steppermotor housing v2.stl" I hope you enjoy this Make :-)

Remix only for part 3 of 3. Added some supports for better alignment and easy superglue the part. ...Printed at 100mm/s part fits fine.

I created the design to follow 0.12mm increments to follow the default Cura settings for Ender 3s. I printed these at 0.12mm to get the best resolution on the spacer thickness. ... You can see these kinds of brackets being used in this video: ...

Simple full power supply cover replacement to install silent fan on the Meanwell PSU of the Creality Ender 3v2. This design is for 80x80x10 fan, in my case i used this one : ...

... Screws used for attaching the bottom and top case are M2.5x6. Perfect for OctoPrint (I have the GPIO pins hooked into a relay board in a separate case to control PSU and LED light). Slides into the channel on the Ender series 3D printer structure.

This is a custom Ender 3V2 mainboard cover designed for the use with a 92x14mm fan (e.g. Noctua NF-A9x14 PWM) in conjunction with a 22x7mm step down converter (e.g. MP1584EN).</p><p>There are clearance holes for using the fan either in a push or a...

This is a custom Ender 3V2 mainboard cover designed for the use with a 92x14mm fan (e.g. Noctua NF-A9x14 PWM) in conjunction with a 22x7mm step down converter (e.g. MP1584EN). There are clearance holes for using the fan either in a push or a pull...

This is a moving camera mount for ender 3v2 neo. I created this to add a wifi camera to my setup to monitor prints. Print this in a lower layer height to make sure the quality it there for it to slot together. The end of the pin did break off for...

Posts to mount 120mm fan under Ender 3v2/Pro motherboard note: this is really still work in progress note2: For this to work, the drawer has to be removed Hardware required: 120mm pc fan, I'm using an old be quiet! PURE WINGS 2, but any other brand...

... Screws used for attaching the bottom and top case are M2.5x6. Perfect for OctoPrint (I have the GPIO pins hooked into a relay board in a separate case to control PSU and LED light). Slides into the channel on the Ender series 3D printer structure.

* Benjiis Bed Wire Strain Relief is not usable for Ender3 V2, because V2 has PSU there. I redrawed new one, using <a href="https://www.thingiverse.com/FourDogs">FourDogs</a> "<a href="https://www.thingiverse.com/thing:2958812">bed wire strain...

- Camera Arm V0 - Original Arm with Radius - Camera Arm v1 - Original Arm with Bevel - Camera Arm v2 - Shorter Arm (z-axis) Added Additional Pivot pins for clearance issues : - Pivot Pin v1 - 0.00mm clearance - Pivot Pin v2 - 0.10mm clearance -...

------------------------------------------------------------------------------------------------------------------------ V2 UPDATE...

Print with supports touching build plate0.2 layer height3 walls

I accidently printed this thinking it would fit my V2 (I know I didn't read his description) So I made this fit. Just elongated between the two semi circles. Fit snug for me. I may remake this and make it a mm or two longer if there are too many who...

Update v2: The previous design allowed for slight extruder flex when filament feed wasn't perfect. This new version now includes a front plate connected to the base via 2x countersunk M6x8 screws (IKEA scraps repurposed). It still works with the...

However, I've included the original V2 version as a precautionary measure. UPDATED: 8-4-2018 The initial (V1) version featured threads to screw on the filament holder. Unfortunately, there was an issue with the threads being excessively loose. To...

This is a hotend housing for the zesty nimble v2 which features a built in and adjustable mounting platform for the bltouch and 40 mm blower as well. Print with the large fan opening down and use supports for two mounting tabs. There is only one...

......For the Ender boards or SKR. Not sure what else will fit. Moved the left side fan hole over and mirrored it over to the right so the pi and main board both are getting a good solid flow of air across the hot bits. Also added the honeycomb cutouts.