ender 3 v2 raspberry pi mount 3d models

This is to go under the LCD on the Ender 3 LCD and it holds a Raspberry Pi 4B. Lots of credit to those that created this. I just added a few. you guys can expand this and do what you will. I added a second version, hopefully. It has a cut out for...

Stand-offs are little higher than original and allow to use both 40x10 fan and heatsink (mount PI CPU-down). You can insert/remove SD Card without opening the case. I uploaded versions with and without bottom vents - I removed vents to use the...

Easy Raspberry Pi 2/3 Holder includes wallmount. Print Settings are as follows: Printer Brand is RepRap, specifically the Prusa i3 Geeetech model. Rafts are not required for this design. Supports are also not necessary. ...Infill density is set at 30...

A simple raspberry pi mount. I added an aluminum 2020 post on the rear to keep the wires from catching under the bed, and for mounting the Octopi set up. The board is secured with a couple screws to the box. ( I inserted the board, drilled a...

Wall mountable case for Raspberry Pi 3(B/B+). ...I needed a way to secure my enclosure and have power directly soldered onto the GPIO pins.\n\nParts:\n3 M3 Nuts\n3 M3 8mm Bolts (Lid)\n4 M3 6mm Bolts (Case)\n1 2.1 MM 5A DC Power Jack Socket Threaded...

This remix is designed to fit more modern Raspberry Pi's (3 and later). The tolerances were tightened up so it should be a tight fit on 35mm DIN Rails and hold the board securely. Also this mounts the boards slightly closer to the rails. ...*Note: It's...

This replaces the original bed clip of an ender 3/ ender 3 v2 and allows a GoPro to be mounted for a smooth time-lapse

Here is first:https://www.thingiverse.com/thing:2703351 Second design, my own (already linked): https://www.thingiverse.com/thing:4602943 This is a 3D rotational Print in Place, tight fit, ball joint based camera mount for Raspberry Pi. connects to...

To seamlessly integrate the Raspberry Pi within this compact server, meticulous care is taken during setup. ...By employing an old HDD tray as the primary housing and securing the prized microcomputer firmly inside, a sturdy framework emerges,...

Ender 3 v2 Mosfet Mount BOM: 12x M3 Hex Nuts 8x M3x12 2x M3x8 2x Nutensteine option: 1x Fan 40x40x10

Simple mount to fit the Bontech BMG extruder onto the Ender 3 V2 while maintaining it bowden tube. ...

Simple mount to fit the Bontech BMG extruder onto the Ender 3 V2 while maintaining it bowden tube.

The only post print "tuning" needed was lightly trimming the posts that secure the end plate with power switch to the aluminum extrusion. Remixed from: https://www.thingiverse.com/thing:4821226 Front mounted power switch...

This solution enables you to add Raspberry Pi units horizontally, layer by layer rather than deciding the number of Pis needed for your cluster during setup.

I wanted a wall mountable case for my Raspberry Pi 3(B/B+) that I could easily power directly through the GPIO pins. I needed something that would fit perfectly in my enclosures. To build it, I gathered these essential parts: * 3 M3 nuts * 3 M3 8mm...

This is a remix of [Adjustable/Rotating Mount for Raspberry Pi Camera V2 by theodroid](https://www.thingiverse.com/thing:1718628) but with an extra file for the Raspberry Pi Camera **V2.1** with a square cutout to fit the wider camera lens. ...Please...

Support for the Pi Camera v2 is on the Y-axis. With good ventilation, the box prints without support. ... It requires an M4 screw and nut.

... I never completed this task due to the effective friction fit of the pegs holding the camera securely in place. The design is a quick fix to replace a missing GoPro case for my Raspberry Pi Zero. ... I hope you find this adaptation useful.

My case model looks like this:...

Raspberry 3 Model B mount.Models created with OpenSCAD, model files also available on Github The RaspberryMount model is meant to be mounted using screws and the RaspberryDeskMount is measured to fit my table (25mm) as a push to fit piece. Both...

To begin with, I rotated the raspberry pi's usb ports downwards to improve accessibility and usability. Additionally, I incorporated a camera ribbon cable cutout to facilitate easier setup and integration. ...While I acknowledge the original designer's...

SSD Server mount for Raspberry Pi board; should fit all full-size models with 4 hole mounting (B+, RPI2, RPI3, RPI4). Board is position so back plane is even with back of SSD. CPU mounts on top, SSD below. Provisions for screw mounts top and bottom,...

Wall mountable case for the Raspberry Pi 3(B/B+). I wanted something I could mount in my enclosures and have power soldered directly to the GPIO pins. Parts: 3 x M3 Nuts 3 x M3 8mm Bolts (Lid) 4 x M3 6mm Bolts (Case) 1 x 2.1 MM 5A DC Power Jack...

Update 2020/07/29: Added STEP file for project. Update 2020/02/10: Updated arms to have greater support for the weight. I designed this camera mount to be used on any 2020 or 2040 extrusion-based printer. You can mix and match the various rigid...

This remix is designed to fit more modern Raspberry Pi's (3 and later). The tolerances were tightened up so it should be a tight fit on 35mm DIN Rails and hold the board securely. Also this mounts the boards slightly closer to the rails.Note: It's...

Fits Ender 3 v2, moves with z axis

The following video has full assembly instructions: https://youtu.be/aPOUPXh9m-g Hardware Needed: Camera: Arducam 5 Megapixels 1080p OV5647 Camera Module https://amzn.to/2IYQOdl Camera Mount: 4 x M3 12mm Screws 2 x M3 8mm Screws 6 x M3 Nuts...

This camera mount is designed for versatility, compatible with any 2020 or 2040 extrusion-based printer. Mix and match the rigid extensions or create your own unique configuration. Watch this video for a step-by-step assembly guide:...

I needed a fast and easy print that would securely hold a Pi 2/3 to the extrusion using standard M4 T-nuts. I used supports touching the build plate to provide stability. The design is intended to hold standard M2.5 nuts on the back side to firmly...

... it longer as well. ... Also the camera case did not fit my v2.1 Pi-Cam, so I remix the case from [Ender 3 Pi cam mount by BartPLA](https://www.thingiverse.com/thing:3868687) and used the ball-connector from this design to allow it to connect. ...