ender 3 v2 touch screen upgrade 3d models

... i have been able to finally create my own model of satsana. This sastana has 3 front mount screws. CR / BL Touch adapter. Direct drive adaptation. And stock parts / Fans only. An amazing piece. ...i hope others are in need of this as i was.

... that i have been able to finally create my own model of satsana. This sastana has 3 front mount screws. CR / BL Touch adapter. Direct drive adaptation. And stock parts / Fans only. An amazing piece. ...i hope others are in need of this as i was.

print in any resolution up to .28, This is just a very basic mount to move the screen to the right and angle it up a little, It is pretty sturdy and doesn't take long to print at all, all you need is 2 more M5x8 bolts, (exact same ones that hold the...

instagram.com/macnayarms/ These fan shrouds can be used on either Ender 5, Ender 5 Pro, Ender 3, or Ender 3v2 using an MK8 (stock) hotend, it features dual 5015 blower fans, and thus greatly increases the ability of printing overhangs. To use...

... the screen. I used 4x 4M x2 20mm countersunk screws with one of them shortened to around 10mm, 1x M4 washer with 10mm~ diameter, 3x M4 spring washers and the 2 stock screws that hold the screen. ... I added a blender file with the screw placement

Highly Recomend 3d printing this cheap and easy model I colored the ender and dragon in with silver sharpieHappy Printing

... cover I needed a smaller screen cover so I made a new one. The frame sits well but It can fall off sometimes it's easy to just replace it. The screen cover blocks out almost all light, you can see the light on the sides but you can barely see it.

Summary THIS IS AN EXTENSION MODULE FOR Ender 3V2 Screen Holder (space reduction) This extension module is made to be included with "Ender 3 V2 Screen Holder (reduce space)". Designed to add a Raspberry pi 3 B+ (or older) under the TFT screen. **...

Remixed tsuga's model to work on E3v2. ...Clearance for X endstop.Original model: https://www.printables.com/model/333070-cr-touch-zero-offset-probe-backplate-mount

This design works really well in terms of allowing one to monitor prints remotely, but one issue I had involved the CR Touch colliding with the camera mount when homing. I edited this part to give the CR Touch clearance when homing. After opening...

Original : https://www.thingiverse.com/thing:3179892 I want use this duct system and CR touch same time. So.. I modified it. ... need extra m3 nut and some zip tie.

This is a remix of the default Creality mount. ...Offset to allow for use with direct drives. You may need to force the screws a bit or lightly drill them a touch wider.

This is a remix from the project of KaminoKGY : https://www.youtube.com/watch?v=yCCTs_8K5yM&t=3s Newer version with BL TOUCH Mount Printed in ABS, 100% filling recommanded. ... Some adjustement might be required.

I've modified the original model with a 2.5 mm lower bracket, this becouse, for some reason my cr touch was to high on the mount resulting in the noozle crashing into the bed while using the mesh leveling.

Made a remix with the following desingns https://www.thingiverse.com/thing:4960249 https://www.thingiverse.com/thing:5141820 https://www.thingiverse.com/thing:4736330 Made this so i can easy change the nozzle and still have the CR touch and laser...

Added a cutout for the CR Touch wire connector and switched the lateral support to the other side of the probe mount. Added the creality dragon to the front. (Dr Boo's Creality Dragon Logo - printable (https://www.thingiverse.com/thing:2873554)...

Remixed the modular arm bracket from https://www.thingiverse.com/thing:4213384 with the modifications to the predecessor non-modular bracket remix that prevents collisions with the CR-Touch sensor (https://www.thingiverse.com/thing:3481096) so the...

Made a remix with the following desingns https://www.thingiverse.com/thing:4960249 https://www.thingiverse.com/thing:5141820 https://www.thingiverse.com/thing:4736330 Made this so i can easy change the nozzle and still have the CR touch and laser...

There's very little room between the x-motor and the CR-Touch, so if you find that my model doesn't work for you, you might also check out [this remix](https://www.thingiverse.com/thing:5276100) by [bkbillybk](https://www.thingiverse.com/bkbillybk)...

:)https://paypal.me/cdsmakestuff Dual Cooling Fan Upgrade with BLtouch Mount Fits Creality Ender 3 V2 Ender 3 (OG) and Ender 3 Pro version Here: https://www.thingiverse.com/thing:5403671 Why another? Well I tried a lot of different existing designs...

:) https://paypal.me/cdsmakestuff Dual Cooling Fan Upgrade with BLtouch Mount Fits Creality Ender 3 V2 Ender 3 (OG) and Ender 3 Pro version Here: https://www.thingiverse.com/thing:5403671 Why another? Well I tried a lot of different existing designs...

back cover for Ender 3 Ender 5

its for peaple that use the spider hotend

Remix for use in Unitak Direct Drive Upgrade Kit for Ender 3v2. https://www.amazon.com/gp/product/B09KG8MMQ2/ref=ppx_yo_dt_b_asin_title_o03_s02?ie=UTF8&psc=1 *The part was rotated 2 degrees to align with the mounting plate. *Added support...

** THIS IS AN EXTENSION MODULE FOR THIS https://www.thingiverse.com/thing:4705966** (NEW DESIGN SINCE 10/2/21 ONLY) This extension module is made to be included with "Ender 3 V2 Screen Holder (reduce space)". Designed to add a Raspberry pi 3 B+ (or...

I can across a Ender 3 V2 screen case FredrikA had designed, and decided I could extend it to also include my phone - It would be 'double screen'. I extended the mount, and made it longer and stronger to accommodate the extra width and extended...

The one that he made works with the stock Ender 5, but recently I upgraded to a Micro Swiss direct drive extruder. The mount that he designed hits the spot where the belt is attached to the carriage plate. The mount doesn't hit the belt clip now...

I really and I mean REALLY wanted to spruce up my CLAPPED a$$ Ender 3 but ran into an issue with the screen.Anyways, this model will allow you to move the screen out of the way so that you can attatch some extra flair.Print in the same orientation as...

If you have upgraded a CR-10 mainboard, you may also want to upgrade the display to take advantage of the extra memory.I designed this mount for the intelligent display that can be found on Ender 3 V2s and S1s or sold as a kit from creality.To get...