ender 3 z offset 3d models

Z knob for easily lifting the z axis quickly without getting fingers or lead screw dirty

Nema 17 Motor Holder / Motor Mount for Steppers till 48mm for z-Axis at a 4040 / 4020 Profile and it's 3,5mm thick. Remember a Stepper could be warm (PLA will very early be weak). Use a Washer under the Screw. ...Für Motor M3x10 and for the Mount M4x12

This is a combination of a filament guide and a z-axis stabilizer, without the need of a bearing. It's printed at 100.3% scale and works fine as is. It's abit loose until you attach the screws again. ... The spacers are meant to space the original...

I purchased a LED strip to go on the inside of my ender 3 v2's frame. The original file is awesome but I could not run the led strip all the way around the frame because there was no space behind this bumper. I edited it TinkerCAD to create space for...

Just another cable chain for the ender 3. It doesnt work with the original extruder. Even if i would make it working, there is not enough space to handle it. But with Bondtech it works fine. Some others maybe too, but the original doesnt even...

Relocates PSU, making room for dual Z-axis leadscrew/motor

I adjusted the bearing carrier upside down to accommodate the Z-axis knob on the Z lead screw.

Diagonal brace for the Ender 3 Clears stock components You will need: 1x 480mm M10 Threaded Rod (Measure before you cut!!!!) 2x M10 Cap-nut 5x M4x10 (Hex head) 5x M4 T-nuts 1x M5x20 (Hex head) M5 Tap With a glass bed I still get full 250mm of...

The Y-axis bed connector I use comes from Tobi0892 design: https://www.thingiverse.com/thing:4316238 I am using a total of 35 chain-link (15 for Y-axis and 20 for Z-axis) and 3 chain-link-cut for the Z-axis. ... Edit: I added the file clip_connector,...

Left X-Axis Friction Fit Mount I put together to mount my Logitech C920 on the Ender 3 S1. You should be able to use any webcam that has a standard 1/4" tripod mounting screw insert. You will need to print out a 1/4" screw to mount your camera. ...This...

The new hotend mount is designed to fit seamlessly onto a standard Ender 3 setup, positioning it right next to the cooling fan. Originally intended for an 18mm sensor, this versatile design can be easily modified to accommodate any size sensor that...

the holder fits on the CR10S pro V1 and V2 as well as on the ender 3. on the printer no screws need to be replaced or loosened just slide it on and mount the camera. the camera housing for the PI V1/V2 you get here:...

Remix z axis drag connector to fit over heat sink on my Z axis stepper motor (from thingiverse.com/thing:5205630).Supports required

Pi camera with IR Ender 3S1 Mount. ...See Original design for mount example

Lube the thread. # Changelog 26/03/2020: Added a beefy version, 0 backlash and 0 flex, end of Z problems. 16/05/2019: Modify to use custom backslash Print instructions4 Perimeters Backslash: 0.1 layer height 3 perimeters turn off: ensure vertical...

... so just peel it off. - Made for an Ender 3 Max Neo but, as I didn't change the mounting point dimensions from Zotty, it should still work on other Ender 3 Models. - May remix again with cable routing built in if I can be bothered! ...

Climb onto the steper and transport the cable chain to the z-axis location.

Guide for the hotend wires if the Z-axis extruder motor is removed.

针对一拖二双Z丝杠驱动的修改版轴承料架。 For ”one for dual Z ender3 machine”. Category: 3D Printer Accessories

针对一拖二双Z丝杠驱动的修改版轴承料架。 For ”one for dual Z ender3 machine”. ... Category: 3D Printer Accessories

For locking the z-axis screw for things such as mounting a laser.

Z connector with slightly elongated chain connector and hole for cables

The two small screws are reused from removing the flexible base from the camera, and I used one random screw about 12-16mm long to hold the camera mount onto the clip / Ender 3 mount. Webcam:...

... the tensioning screw falls on, I made several versions. The thickness of the base plate is 3,5 mm. Print with 100% fill. I only used support for vertical through holes. Slicing program PrusaSlicer 2.6.0-alpha6, printer Ender-3 V2 Neo 0.4 mm nozzle.

**Parts List** The guide includes a list of parts needed for the upgrade, including: * Rails (2 x 350mm mgn12 Linear Rails with mgn12H blocks) * Hex Socket Cap Screws (24 x M3x8mm) * T-Nuts (24 x M3) * Left Side components (4 x M3x6mm screws, etc.)...

Z-Axis Stepper Motor Planetary Gear Upgrade **What this mod does:** The Z-axis stepper motor works at 1.8° steps, with a quad threaded lead screw that raises the X gantry by 8mm per revolution. 200 steps in a full circle, with 0.04mm per full step.

Just another Z Offset Calibration test, printed in 4 mins.

I have only tried this on the  Ender 3 pro; other printers may have the holes in the correct place.To check your lead screw - move the gantry to the top (as seen in photo) and measure gap. Then measure the gap closer to the stepper motor. I had a...

the holder fits on the CR10S pro V1 and V2 as well as on the ender 3. on the printer no screws need to be replaced or loosened just slide it on and mount the camera. the camera housing for the PI V1/V2 you get here:...

I needed a mount to attach my Nikkei extreme to the Ender 3 using a clip-on, but after searching extensively, I couldn't find an STL file anywhere, forcing me to take matters into my own hands. Having only owned a printer since February 14th, I'm...