ender 3v2 board 3d models

Ender 3 v2 mainboard cover For use with: - 80mm Fan - LM2596S Buck Converter with Voltage Display

Specific to those that have Unitak Direct Drive set up on theyre Ender Printer This cover fits nicely over the ugly motor!

Dual Blower Fan Duct for Ender 3 V2 with Creality Spider V2 Hotend and Inductive sensorBased on the MBOT3D MK2_Rev2.0 by Ahmad Sunardi, I have designed this Dual Blower Fan Duct for the Creality Spider Hotend V1 installed on the Ender 3 V2 3D...

When using a V6 nozzle on an Ender3v2 (or other Enders), often one loses 6mm y-axis range. This is caused by the hot end mount that has 6mm more offset compared to stock. The lost range can be fixed by shifting the metal frame and drilling new...

The whole thing is just a little bit bigger than the original fan duct of the Ender 3 V2 and the extra width to the right side (where the part cooling fan sits) does not affect the functionality at all. The fan duct is created to perfectly fit two...

This design is a remix of two different STL's found on thingiverse, I used the "QR Code Cover Ender 3 V2 CR-Touch" designed by 3ddruckmarc and for the insert I used the "Deathly Hallows Logo" designed by Remanater. I imported both files into blender...

Basically I needed to modify the fan shroud because the Spider All-Metal Hotend is a bit bigger than the stock hotend that comes with the Ender 3 V2. I did have to use spacers and never modified the STL any further. So I am using threaded heat...

Check out my new duct design: ###https://www.thingiverse.com/thing:4807645 Solar Orbiter Duct has the following features and advantages over this: - ender 3/pro/v2 compatibility - version with or without printed bltouch mount ( + bltouch cable...

https://www.amazon.com/dp/B07R4ZBBC4?psc=1&ref=ppx_yo2_dt_b_product_detailsHot End LED: https://printermods.com/collections/led-lighting-kits/products/led-lighting-kit-for-3d-printers-hot-end-versionPrint SettingsPrinter Brand:CrealityPrinter:Ender...

This is a BLT-friendly remix of the very excellent [Satsana duct](https://www.thingiverse.com/thing:4369859) for Ender 3 series (including v2), for use with a 4010 hot-end fan and 5015 blower. The model preserves the original offsets I used for the...

Another remix of the Satsana V52 with a direct drive bracket I designed. This one that I designed shortened the bowden tube length by 8mm. My previous setup was https://www.thingiverse.com/thing:4662728 The Satsana fan duct is remixed to be used...

Original direct drive from Creality came with plastic feeder , so I designed motor mount too use with my dual aluminum feeder.

Made this display outline cover because I didn't want to print a whole screen case (too much red for the black&red theme I have). I ended up just making it flat so I could glue it on but I included a version that has a lip to sit on the case. knob...

Original design worked as it should. Didn't like how mall the pick up knob was so i added a knurled knob. It is a bit taller and more tactile to the fingers. ...No other changes were made to size of cover, fits the screen tight and lets very little to...

STL`s are big becouse are in high quality! For fix You need 2 pcs 608 bearing and orginal screw for filament holder everything fit smooth on my printer if You get problems with screw change size in Y and X 2% less or more Inspiration i took from...

This is my small project. I very like Voron extrude but I wanted a more compact fan duct so I redrawn it Use M3x10 screws to connect the parts. ... No support needed when printing

just print as is with your best print settings

Edited Knob for a Embedded Nut with stop at layerhight command. ...

I changed my printer to Direct Drive from microswiss. Unfortunately, the direct drive is not compatible with the original hotend. So i adapted my own creation to the backplate of microswiss. ... Have fun!

I now have a Direct Drive and I wanted a way to feed Filament from my Filament Dryer to the center of my top rail.

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

Another tool holder. Added some extra holes for scissors and nozzle cleaners ect. Added front container for holding screws and crap you don't want to lose when fixing your latest effing printer issue or upgrading something that completely does not...

I remixed this design with an extra height of about 4m to give the Notcua 80x25mm fan better fitting room. ...I also removed the buck converter mount because it is not needed with the Noctua fan.

Customized version of https://www.thingiverse.com/thing:1169605 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1169605

this work in progress is a mix of https://www.thingiverse.com/thing:4559133 and https://www.thingiverse.com/thing:4545252 as I have the bl-touch original plate installed so I had to adapt the pen holder

Thanks to roblpetty for great source design. I took some of his advice and made the following changes... - moved the mainboard mounts slightly higher and towards the rear for better access. - filled in the top two lid holes - rounded off the...

End-clip requires 101% scale.

Z Axis Mount Tripod/Webcam, slides on the right side of the Z Axis arm, uses a standard tripod 1/4inch screw to lock cam into place.

original BL touch was mounted in a way that blocks the mounting to x carriage mount is from thingiverse making it difficult to adjust too toolhead i am also using cr touch mount comes from satana before using voron i was using this mount. ...thanks...

This Model was created because I couldn't find a properly fitting nut screw for the Z-Axis. I personally love the small version, as it leaves some space for the thumb between the aluminium profile to pass by. ... contact me, if you require different...