ender 3v2 filament sensor 3d models

Irgendwann kommt man an den Punkt wo man einfach so viel Zubehör für seinen Drucker hat das man mehr Platz braucht. ...Ich wollte nicht wie die meisten hier in die Höre, sondern konnte in die Tiefe gehen, da mein Drucker eh auf größeren Beinen steht.

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

This product is,designed to protect your screens.

Edited Dual Cooling system of the Satsana design Original was designed for cooling fans 40x40x10mm. This design is for 40x40x20mm Blower fans. ... Have yet to test it, only concern is the openings towards the Extruder end might not be big enough...

Remix of the following: https://www.thingiverse.com/thing:4408737 https://www.thingiverse.com/thing:4578487 Combined the features of both designs and integrated the clips for the ribbon cable to simplify assembly. ...

Printed at 25% infill

Covers the screen completely. To be printed with support. ... Nozzle 0.4mm Infill 20 Layer high 0.20 Printing time 2h50

I decided to remix a remix to better fit what I wanted out of a Tool Holder for my 3d printer tools. I wanted a spot for storing the SD cards that I use in my printer. I use standard size SD cards so I made a version with 2 SD card slots. Knowing...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

Needs to be printed with a lot of support and low layer height. In addition, support should be locked in the middle of mine. ...Not an easy print.

This is a mount for a Raspberry Pi Camera V2.1. It stands far enough away from the build plate to show the whole plate while printing. ... Additional to these parts, you will need: - 3mm bolt and nut for the mount - 5mm bolt and but for the swivel -...

Have to tap the RHS profile with M5 tapRequired hardware:M5x20 cap screws   4pcsM4x8 button head   2pcsM4 roll-in T slot or hammer nuts   2pcs

Simple PSU cover for Ender3v2, that hold origina 60mm fan. ... I have added honeycomp on all cover for better ventilation.

I wanted a sturdier bed handle that could also be used with a single finger if needed.

Just added BLTouch mount to fan duct. ... X Offset: -46 Y Offset: -8 This is a remix from https://www.thingiverse.com/thing:4674061

I decided to remix a remix to better fit what I wanted out of a Tool Holder for my 3d printer tools. I wanted a spot for storing the SD cards that I use in my printer. I use standard size SD cards so I made a version with 2 SD card slots. Knowing...

This is a remix of the Ender 3 v2 cable chain mount by gorillale - combined with the roller guide + runout sensor by chrisirwin. ... Thanks both of you for your excellent work!

This is a remix of the Ender 3 v2 cable chain mount by gorillale - combined with the roller guide + runout sensor by chrisirwin. ... Thanks both of you for your excellent work!

Link: https://www.banggood.com/fr/Lerdge-1_75mm-Filament-Material-Run-Out-Detection-Module-Sensor-For-3D-Printer-Parts-p-1323359.html?rmmds=myorder&cur_warehouse= CN Or :...

The first problem was the filament sensor, as part of the point of going for direct drive was to get away from the long Bowden tube, so I decided to make a cable support and filament sensor all in one. As the filament sensor, I used the Creality...

The first problem was the filament sensor, as part of the point of going for direct drive was to get away from the long Bowden tube, so I decided to make a cable support and filament sensor all in one. As the filament sensor, I used the Creality...

I remixed ptsiampas' sensor mount to include a cable chain anchor. The editor won't find the original, so here's the link: https://www.thingiverse.com/thing:4765622 Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No...

This is a filament runaway sensor for Ender 3 Pro which is re-using the z endstop switch. After I installed the BLTouch bed leveling I have one switch free to use for something :) It is cut in 2 and you need to glue it after printing. This is...

This is a filament runaway sensor for Ender 3 Pro which is re-using the z endstop switch. After I installed the BLTouch bed leveling I have one switch free to use for something :) It is cut in 2 and you need to glue it after printing. This is...

I scanned in the filament sensor and created a shim so that the new dual gear extruder lines up with the filament sensor. Otherwise the filament has to make quite a turn...Which may be fine for flexible filament, but won't work with others. This...

Models: -Bracket -Ball bearing adapter x2 -Leadership -bolt screwless ;) Filament Führung Kann direkt unter den Originalen RunOutSensor geschraubt werden, mit den Schrauben des Sensors oder mit M3x30. ... Modelle: -Halterung -Kugellageradapter x2 ...

I moved the sensor rearward on the mount, and added a gusset to support the overhang of the sensor backing plate. Printed base down with tree supports. 10" infill with 4 wall, it's plenty strong and should print in a couple of hours max, I was...

2021 adjusting position the sensor for better filament flowing UPDATE 28. 02. ...2021 when you use aluminum extruder upgrade, use my remix filament guide: https://www.thingiverse.com/thing:4778629 Print Settings Printer Brand: Creality Printer: ...