ender 3v2 filament sensor 3d models

I found some amazing parts here, including a cable chaining system from the extruder to the hotend, a modified extruder with a nut to secure the PTFE tube in place, and I also wanted to add a filment runout sensor, so I decided to combine all these...

This is a Filament Runout Sensor (FRS) mount for a sensor that uses 4 screws. I designed this for my Ender-3 v2 with the Creality Titan Direct Drive using TinkerCAD, https://www.tinkercad.com/things/jnTaDbgEz4M . I was inspired by the Creality CR-10...

I design this to uplift the cutout sensor to fit the height of the Bigtreetech Dual Gear extruder MK8. ...This allow to level the filament exit of the sensor to the entry of the extruder. ...You'll need 4 x M3x20mm to bolt it to the frame.

... Y and Z if you send me a comment with the measured values after you print off my version first. ... Biqu Filament sensor with mounting holes near center in Z direction Used M3x20 QTY 2 and nuts for sensor Used M4x16 QTY 1 threaded into the print. ...

This design is made to accommodate the position of the filament sensor for direct feed. I matched the screw holes to the sensor I purchased. Other models may require a different position of the screws. ... The device is adjusted to the top profile of...

Link: https://www.banggood.com/fr/Lerdge-1_75mm-Filament-Material-Run-Out-Detection-Module-Sensor-For-3D-Printer-Parts-p-1323359.html?rmmds=myorder&cur_warehouse= CN Or :...

It does not come with a mount for the filament sensor, this slides onto the existing nut if you are side loading filament. By the way. ...This goes at a slight angle, allowing for the filament to just go in smoother.

... The model is still a WIP and subjected to improve in time. It is design for holding the filament sensor while guiding the filament from side to the Direct Drive module, utilizing the original filament holder part.

... adjustments to fit my stock Ender 3 Pro printer. ...I needed to move the wheel and sensor down by 8mm and out by 2mm to align correctly with the basic stock extruder. ... I have also included the bearing spacer and roller from the original design.

I made this housing for those who want to use the z limit switch laying around as a filament runout sensor after installing BL touch. I designed this housing to use with a couple of skate board bearings so it doesn’t grind the filament when it goes...

This is a Filament Runout Sensor (FRS) mount for a sensor that uses 4 screws. I designed this for my Ender-3 v2 with the Creality Titan Direct Drive using TinkerCAD, https://www.tinkercad.com/things/jnTaDbgEz4M . I was inspired by the Creality CR-10...

... M3x10 with M3 nut **UPDATE 13. ...02. 2021** - adjusting position the sensor for better filament flowing **UPDATE 28. 02. ...2021** - when you use aluminum extruder upgrade, use my remix filament guide: https://www.thingiverse.com/thing:4778629

I could not simply enlarge the model in the slicer, because that also made the distance between the holes greater, and it seems the tubing hole was too far away from the filament inlet anyhow (it seems it would have been off to the left even if I had...

I personally use my switch with Octoprint in conjunction with Filament Sensor Reloaded (https://plugins.octoprint.org/plugins/filament_sensor_reloaded/). Here are the instructions: Just make sure to support the cylinder that holds the bowden tube...

Mount for simple filament runout sensor. Placed instead of bowden extruder which is exchanged to direct one. Assemble: - put two M3 nuts in the bottom of the mount - attach mount to the printer's frame with 4 M3 bolts - mount runout sensor If you...

Este soporte es 2 cm mas pequeño que el que trae la ender 3v2 para poder cambiar, yo lo tube que hacer por que mi ender no cabia en mi repisa.

I did not see any mounts for the Ender 3 V2 with a Trianglelab BMG V2.0 I decided to make it two pieces so I could print them in the orientation I wanted and without a ton of supports. Print in the orientation from Cura pictures. I used an...

Like the original, height is set for Dual Gear extruder: https://www.amazon.com/gp/product/B0B6PBKJYG/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 I used this Filament sensor which looks to be exactly the same as the EZout one:...

Combined DEJello and Holspeed designs and made a filament runout sensor enclosure that bolts onto the X gantry. Included a PC4-M10 input thread. If tolerances of printer aren't right and you don't want to adjust, just use a M3 bolt to help secure it....

Remixed This Design:https://www.thingiverse.com/thing:6585239I added:thread for the PTFE-FittingSrewholes to screw on a flat surfaceTheere is a version with Screw holes and one without, if you only want the thread.I srewed my sensor on bottom on the...

... and doesn't need screws to mount the 608 bearing. It supports the EZOut v2 filament sensor but also the knockoff from aliexpress https://a.aliexpress.com/_mrORqcU Also made some modifications to use less material and make it look more stylish :)

This is an add-on adapter for the Ender 3V2 and should also fit any of the Ender 3 series with the same filament holder. This adapter does not replace or modify the factory built holder. Instead, it is a simple set of two bearing holders which clip...

Remix version of Norp's extruder-mount-31mm-alu.stl This removes the filament guide and extends to bracket to allow it to be fitted and secured using the filament sensor holes. The picture of it fitted is the 2.8 version which fits fine, version...

After upgrading to the BLTouch I decided that I wanted to do something with that dangling Z-stop sensor, so what better than repurposing it as a filament sensor. After much googling, I came across a couple designed and decided that I wanted the best...

QR Code cover for Ender 3 / 3v2 etc. Canada flag maple leaf cutout. ... For the red, I backed the cutout with a piece cut from a Fruit Loops box.

Cable guide for Sprite Pro for Ender 3v2. Mounts to the top of the old extruder motor mount. ... Needed Hardware: 4x M3x8 screws, 4 M3 washers and 4 M3 nuts.

Print 2 each, Male connects to female part. ...(I recommend using a glue in the female part to ensure that it sticks. Use 40%-60% infill.Compatible with Ender 3v2, basically anything with aluminum extrusion slots

Modified version to give a little more room between the extruder and the sensor.

One of the final pieces of the puzzle was figuring out how to mount my filament out sensor properly. This housing mounts seamlessly into the v-slot of the 2020 extrusion on top of the printer. If you plan to install a spool holder on the top rail,...

One of the last pieces of the puzzle was to figure out how to mount my filament out sensor. This housing mounts in the v-slot of the 2020 extrusion on the top of the printer. If you mount a spool holder on the top rail it is STRONGLY suggested you...