ender 5 filament guide 3d models

Although the filament feeds straight into the extruder, I designed a filament guide to prevent the filament from rubbing against the input of my metal extruder and leaving behind filament dust.\r\nThe Extruder uses the original mounting plate, so it...

Filament guide for relocating the filament spool to the side of the printer. Attaches to the back extrusion with m4x10 bolts and t-nuts. Mine is setup on the right side, but it can be mirrored to place on the left side of the printer. ...

Hardware needed: -M8 tap -M8 bolt -608 bearing

20mm x 40mm filament guide for the ender 5. ...Holes are 4mm on center.

A Combination Filament guide and Cable clip for Ender 5 and Ender 5 Pro with unmodified extruder position. No T-Nut or Screws needed. You need to file the clearance for a tight fitment. Use a short PTFE tube to help glide the filament through. ...

This is my take on a filament guide for a Direct Drive Conversion on my Ender 5 Pro. It uses a Bowden tube mount to keep the original spool location intact. The design features a removable tube assembly for attachment to the extruder, which can be...

This is my take on a filament guide for a Direct Drive Conversion on my Ender 5 Pro. It Uses a Bowden Tube mount to keep the original Spool location. It has a removable Tube assembly for the attachment on the Extruder. I made it Mount with a M5...

Filament Guide Upgrade for Ender 5 in Direct Drive Mode. I've recently completed a V4 rebuild, incorporating subtle design tweaks to the angles and eliminating the lateral filament entrance altogether. This new version marks the culmination of my...

We required a filament guide solution for the Ender-5 direct drive upgrade kit. This is the most straightforward option we came up with, without relocating the spool holder. All you need is the printed part (5-10 minutes) and the rest should be...

I reduced the width of the original design to avoid hitting the X carriage when moving in the Y direction. This will fit an Ender 5 with a direct extruder. Category: 3D Printer Parts

I adjusted the dimensions of the initial plan to prevent it from colliding with the X-axis when navigating along the Y-axis. ...This modification allows for seamless movement on my Ender 5, equipped with a straightforward extruder setup.

This may be really specific to my direct drive setup on my Ender 5 but I find it useful, so I'm posting in in case anyone else can use it. I use this in conjunction with https://www.thingiverse.com/thing:3628876 by Daede to lift my Bowden tube up...

This may be really specific to my direct drive setup on my Ender 5 but I find it useful, so I'm posting in in case anyone else can use it. I use this in conjunction with https://www.thingiverse.com/thing:3628876 by Daede to lift my Bowden tube up a...

This thing is not usable for the Ender 5 plus direct driven. Remixed from thing #4134230 This is my first attempt at using any kind of design software. I went with TinkerCAD for my first one. Changed overhangs to be supportable for no...

This is an Over The Top (OTT) Filament Guide for my Ender 5. Using a Direct Drive Extruder, the filament feeds from the top, so being inside an enclosure without a solid top I needed to devise a way to safely keep the filament free flowing and free...

Direct Drive Setup Guide: Securing Filament on Your Ender 5 Get a solid grip on your filament with our simple direct drive setup for the Ender 5. This guide shows you how to keep the filament in its original position. For the Single Bolt Version,...

I upgraded my Ender 5 Pro to direct drive and was in need of a filament guide for the top-rear-left mounted spool. The new guide is 20mm wide, secured with M3's and T-Nuts. It's set at 45 degrees to avoid any sharp bends when the filament is centered...

This is a remix of Filament_Guide_BowdenTube_V2 to make it a bit stronger. Where the bolt goes through, I broke mine with movement so made this version to make it thicker. ... You will need a slightly longer bolt (M3x16 fits perfect) as it's 2.5mm...

I got tired of my filament snapping on long drives to outside corners, so I wrapped it in wasted Capricorn Bowden tube I lost with a Direct Drive upgrade from Printermods.com. You'll need two male straight pneumatic PTFE Tube Push in Quick Fitting...

Filamentführung für Ender 5 Ihr benötigt ein Kugellager 11x5x4 sowie eine passende Schraube mit Mutter M5 Zur Befestigung werden zwei kurze Schrauben M4 mit Hammermutter benötigt Weitere Informationen zu meinen Drucker Modifikationen findet ihr hier:...

Filamentführung für Ender 5 Ihr benötigt ein Kugellager 11x5x4 sowie eine passende Schraube mit Mutter M5 Zur Befestigung werden zwei kurze Schrauben M4 mit Hammermutter benötigt Weitere Informationen zu meinen Drucker Modifikationen findet ihr hier:...

Remixed from https://www.thingiverse.com/thing:3872001 Added more legs for stability. ... Added threading for M10 and M6 bowden couplers because Ender 5 kits contain an extra M6 bowden coupler and also to remove requirement for a nut.

It was time for drastic measures, so I decided to overhaul my direct drive filament guide and give it a stylish makeover. I added feet and a slot for an end-of/broken filament sensor to the mix. With the new front feet in place, the block attachment...

For the assembly, I used the original detector's screws of the Ender 5. Be careful, the holes are deliberately narrow, so you have to use an M3 tap, otherwise you have to pass once an original screw "in force" to create the tapping allowing the...

I was asked to share links for my spool holder. Here's the story - I first printed one from Thingiverse, specifically this model: https://www.thingiverse.com/thing:3732566. ...Then I wanted to print another one, which you can find at this link:...

A simple filament guide for direct drive ender 5/pro

**Original** DD Filament Guide.stl - Replaces the shim between the stepper and extruder body, adding a holder for a PC4-MC6 PTFE connector. Better version below if you have a spring handy. ~~DD Extruder Body.stl - Replaces any generic 4mm thick...

End Caps for Open V-Slot 2020 with Open Hardware logo. ... This is a remix from https://www.thingiverse.com/thing:398515 Just replaced the clip from original with a snap clip for the side of the rail (small side, ~25 MM)

I needed a filament guide when I upgraded my Ender 5 Plus to direct drive. With this I could have the filament spool sitting the same place as before. This is mounted instead of the old extruder. Hardware required: 2 x M3 Bolt 2 x M3 Nuts M6...

... design, expertly crafted by SkullKill and available on Thingiverse at https://www.thingiverse.com/thing:3831715. ...A clever addition to this design includes a filament guide that has proven highly effective for my E3D Titan Aero Direct Drive setup.