ender 5 plus electronics case 3d models

This is a modified Version of the aftab's cable chain tray: https://www.thingiverse.com/thing:4164988 enjoy it :-)

The Linear Rail Brackets from Ralp57 (https://www.thingiverse.com/thing:4487342) suggest what I felt was an unnecessarily complicated way to raise the Z screw and Z linear Rails. You need to raise the bed when fitting linear rails because the X...

I remixed the Bed Rod Holder to allow attachment from the bottom of the extrusion, instead of the side. This allows for additional clearance for a left mounted probe on a long hotend like a volcano. ... I now only need 2.5mm of clearance to avoid...

This is a remix of: https://www.thingiverse.com/thing:3842765, but it woudn't find it when I checked remix... This adds the option to use the front mounting holes to secure the screen enclosure. I also added a large lip to the back underside with the...

This is included in the Files. All parts print in the given orientation with NO supports or brims. I recommend you print the parts in PetG. I used M5x12mm bolts to replace the grub screws in the 60t pulleys for better grip. Lightly sand...

The carriage wheel spacers now fit through the part for a more secure location. A support tube now keeps the Bowden tube from flopping over to one side. I didn't like how the corrugated tube was bundling cables with the Bowden tube, so I removed...

Hay just wanted to share the First thing ive made :) This is a No Bolts Clip on spool arm holder made to work with "Filler - The Customizable Filament Holder" (https://www.thingiverse.com/thing:3020026) it is also maded to move your spool...

This is a mounting plate to put the BTT TFT70 on the lower right front corner of the machine. I got fed up with not having a place to put it, so this solves my issue. I printed in PLA for the draft that you see in the photo, but you may want to...

A remix from @bamcdo. I just changed the size of the holes down to 3mm which I used M3 screws to put through tightly and can use any sized washer >3mm in diameter. The original remix from bamcdo, the holes were just too big that I didn't have any...

I made some changes to the design, but I couldn't make it fit around my machine's bearing sleeve, so I came up with an alternative based on the DIYPark original. To fix the issue, I lengthened the main arm and increased the ID of the bearing sleeve.

No supports, adjustable head angle, two M3x20 Feel free to support me with DOGE ;) DSmeW6UgGQEGP4gbfWfYAeP6aX3U1yhGju

Infil 30% ABS bearing 688z screw 4mm

I liked this design, but wanted to use it with an E3D Volcano and an EZABL Pro. The Volcano will mount directly to the BMG. I also moved the location of the hotend fan to be higher. I added an EZABL mount to the left side.Lastly, I cut away the...

I made an error in the BLTouch bracket height. If you have already printed V1, my apologies for the wasted time and filament. A few mods; all of the hard work had already been done: - I raised the filament sensor so as to clear the Hemera...

This is a motor mount designed to mimic the stock motor mount with the lower section where the filament runout sensor would be removed. I used this mount while working with the 3DChameleon MK2 as I needed a way to mount two motors side by side...

Touch Sensor Protection System: Preventing Catastrophic Failure We designed this system specifically to safeguard the BL touch sensor. Its primary function is to protect against X-axis runaway, a potential cause of sensor damage. By implementing...

for SKR2

Designed to support the heat bed cables to help take some of the strain from the solder joints of the cables when bed is at the high positions. Undo the 4 pcs m4 screws holding the linear guide bearing, slide it between the guide bearing and...

He creado esta pieza para ayudar a recoger los cables aquellos que utilicen Hero Me Gen4 Dual 5015 Cooling System https://www.thingiverse.com/thing:4523667 Junto con Extrusión directa. ... Impreso en PLA

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

I remixed the Microswiss X_Carriage with 3 screwing positions for an inproved grip. On the right the M3 hole must be drilled to 4,2mm. ...The hole on the bottom must also be drilled (I was not able to edit it right...) It's my first time I was able...

I changed this up to have a bit more on the end of the arm. I hate when a design is cut off. It looks weird. I also made the mounting holes for M4 flat heat screws, as that was what I had on hand. ...I T-nuts are also from the filament sensor that...

Frustrated with cords constantly jamming into the limit switch and disrupting your printer? This is the answer. ... Design by: 3D PAT CA

I made it almost 1 to 1 with small changes. it works since the replacement perfectly. ... Be sure to print it with 4 lines for the wall and 50% infill for a longer lifetime.

Optimised flow for more cool air for the extruder

Uses the stock mounting points and converts them for a BTT Manta M5P Board. Also moves the Bed Mosfet down out of the way. ...Fusion 360 file included for remixing, please link if you do.

Changed the Desgin a bit because i had the problem that my modded fan duct hit the thing while leveling.

Hardware needed: -M8 tap -M8 bolt -608 bearing

Led Light Bar für Led Streifen 8mm. ...Befästigung der Led Streifen zusätzlich mit Kabelbinder möglich.

I've adapted the style of belt tensioners on my Y-axis by shortening the inner arms, allowing them to press firmly against the front horizontal extrusion. Having successfully implemented this modification, I was pleased with the outcome. However,...