ender 5 plus electronics case 3d models

The Raspberry Pi 3 is housed within a compact Raspi 3 case, allowing users to safeguard their device while also adding a touch of style and protection.

There is a hole for the WiFi antenna on the side and the display cable fits behind the case. I used M4x4mm heat set inserts for the board mount with M4x6mm screws and M3x5.7mm inserts with M3x6mm screws for the lid. The fan and fan lid are just...

The UltiController, featuring a click-encoder, screen for monitoring, file selection, SD card slot and designed to work seamlessly with the provided electronics, is also available for purchase. ...Official Ulticontroller files have been released on...

... on Thingiverse, specifically https://www.thingiverse.com/thing:3502425. ... For those who are curious about my Super-Silent Ender, I've written an article that provides more information here: https://www.3dpedie.cz/en/inspirations/octoender_by_kiron/.

The Duet 3 Mini 5+WiFi is the same size as the older Duet 2 with a few changes to the layout so the original case design would not work. I like their design so it was modified to fit the new board. The printer has a smart filament sensor so a slot...

... 2 parts to simplify the installation. With this you can install the main case comfortly because the screw holes are easy to reach. Then you can install the raspberry on the other side, make all connection and then install it to the case. ...

So I designed and printed this case due to having a specific camera and no previously designed cases would fit properly.... So FTIJPI after I design it, lol. Added and swivel and tilt feature so ensure when assembling that you do not tighten the...

#HEY YOU GUYSSSS# **YET ANOTHER RPI CAMERA CASE...** So I designed and printed this case due to having a specific camera and no previously designed cases would fit properly.... So FTIJPI after I design it, lol. Added and swivel and tilt feature so...

This is a modular electronics case for 3d printers which I have used successfully for my Eryone Thinker (located underneath) and on the side of a Ender 5+The attached model files provide the outer wall and any bases required.  In addition you...

... Original Camera Mount: https://www.thingiverse.com/thing:3747437 Original Pi Case: https://www.thingiverse.com/thing:3349103 Future enhancements: Expanding the top clamp to match the height of the main clamp integrated into the body is a priority.

Anet A2 Electronics & MOSFET Case This small case securely holds the Anet Controller board and a MOSFET module in place. Why did I design this? Electronics are hazardous when they're not fully enclosed. Additionally, an external MOSFET module...

https://www.thingiverse.com/thing:4441076

A simple tool holder to hold the wrenches, hex wrenches, scraper, cutter, and screwdriver that come with the printer Mounting requires: - 2x M4x10mm or M4x12mm bolts - 2x M4 T-Nuts - M5 will also work, but you will need to expand the...

https://www.thingiverse.com/thing:4441076

Simple stock ender 4 electronic case upgrade

When I encased my Ender 3 inside a spacious IKEA PLATSA (120x80x55 cm) box, I urgently needed an enclosure for my electronics to keep them cool and create room for even more mods :) This project is far from flawless but it satisfies my requirements.

This set of files allows users to create a printable box for various electronics parts, including different versions of RepRap electronics. The box's open front design caters to the numerous wires that need to exit it, such as from four motors, six...

Needed a case for the Sure Electronics AA-AB32261 pre-amp, which has holes for RCA jacks and a cable hole on the opposite side as well as a hole for the DC plug. There are no vents in this design. I should have taken a photo but now it's buried deep...

++Complete new case for the electronics on my Sunlu S8++ It fits nicely under the printer and attaches to the metal extrusions with some screws. You also have to remove the old front case and print new foots for the front. Then the old rubber feet...

... Ender 3 Pro electronics housing... ... It's a remix from SKR Case Ender 3 and Ender 3 Pro by Mvieleers! Just adopted to my needs... - Raspberry Pi 4B - buck converter - relais - SKR e3 mini Let me know if you have question. ...Have fun :)

On this case, the display cover is detachable, so you may replace it easily with a different one, say for a standard RepRap Full Graphics display. It also has got a V-Slot rail mount, which will fit most of the 40x40 extrusions you'll find on 3D...

On this case, the display cover is detachable, so you may replace it easily with a different one, say for a standard RepRap Full Graphics display. It also has got a V-Slot rail mount, which will fit most of the 40x40 extrusions you'll find on 3D...

A straightforward task to uncover the electronic components of the innovative Sphere-O-Bot. ...The accompanying FreeCAD file provides a detailed blueprint for inspection.

A case for my mini CNC. ... Category: 3D Printer Accessories

Accommodates the central Anet electronics panel and features provisions for two mosfet boards, which serve as power suppliers for the heat bed and extruder. ...Additionally, it includes two pre-drilled holes with meshed fan grills to facilitate the...

Here is a replacement text that retains all details of your original entry. ... An electronics housing made for the Melzi 2.0 reprap needs two forty-millimeter fans as well as a few pushbuttons and switches.

Installed a Noctua A12x25 for ultra quiet cooling Printer Parts | | Screw Type | Amount | |--------------------|----------------|--------| | 4.2.2 mainboard | M3x5 | 5 | | Power Supply Unit | M5x20 | 4 | | Power Socket | 4,5mm | 2 | | Raspberry Pi 4...

... Enclosure Plugins. ... Rpi GPIO are connected to a breakout board with some electronic component to power (12v, 5v, GND) and manage properly: 2x PWN 120mm Fans 1x Neopixel 60 LEDSs strip (RGB) 4x Relay ports 3x 1-wire DS18B20 temperature probes

Remixed to be used with M5x12 (metric) screws instead of the M5x8. The base of the mounting bracket is a bit thicker (6mm instead of 4mm). ... I also added a small chamfer to help printing and distribute the mechanical load.

Change the guide to a 45 degree overhang so no supports are needed