ender 5 plus modifications 3d models

Wanted to test out HexOrt inspired wobble wings on the ender 5 plus to see if it would help with layers lines. ...After about 2 months of testing, I can say they have significantly reduced layers lines on most of my prints.</p> <p>Will Need:<br/> 10mm...

Suitable for Ender 5 plus with stock frame, carriage and Creality supplied cable cover. ... Video: https://youtu.be/mEacAYde8OE You can find the Direct drive filament guide here: https://www.thingiverse.com/thing:3872001 Voron Afterburner :...

Designed to replace the stock Filament Sensor that ships with the Ender 5 Plus. Should line up perfect with the existing hole pattern under the extruder. I used a brim but supports shouldnt be needed. 10-15% infill should be fine. If you plan on...

This is a mount to allow you to put a BTT TFT35 v3.0.1 screen in the Ender 5 Plus. It is slightly recessed so that you don't have to cut a notch in the opening for the dial. Have not tested a print yet. Simply printed the original and noticed some...

Made a mashup of my previous remix for the ender 5 plus and the mini satsana for the ender 3 (Ill credit when i can figure out which one) You will need to add custom supports under the two risen areas for the BLTouch mount. otherwise no other...

This is a Remix of a Cable Support for the Ender 5 Plus. But i didnt find that Thing again on Thingi. I just made the space between the holder bigger so it fits with the original BL-Touch Plate. You have to ad support to the holder but not to the...

My Ender 5 Plus was extremely loud, so I changed all its fans. The loud one at the nozzle was swapped with a 40x20mm Cooltek one (very nice result) and so it did not fit into the normal metal duct. This one is designed in the same style, only...

DE: Ich habe noch eine vernünftige Halterung für meinen Ender 5 Plus gesucht, in der ich den Bildschirm von BIGTREETECH unterbringen kann ohne dass es zu aufwändig wird oder gar eine extra Box an einer Seite steht. Ich finde das Design vom Ender 5...

Creality Ender 5 Plus Accessory: Simplifying Filament Feeding Inserting filament into the feeding units on your Creality Ender 5 Plus can be a frustrating experience, especially when they're positioned below the print bed. This is where our...

DO NOT OVERTIGHTEN Tested Print Settings Using 3D Fillies PLA+ Glass_bed_clamp_v1 Tested with cura standard quality 0.2mm with ender 5 plus Print Verticle with Brim support for extra strength. Tap maybe needed if unable to get threads overhang...

Just print upside down, can be printed without supports.Original text:"Remix from @Bilgaard mount so this accomodates a Repraps 12864 LCD on the Ender 5 plus. Mount fits the LCD perfectly with a small opening to get to a reset button if...

Hello All out there , Here's a proposition for a Z axis lead screw Guide for ender 5 plus printer. Drawing is extra simple . See following Videos : https://youtu.be/0vTzRNAVvf0 https://youtu.be/bXGqCE6AxoA You will need : 4 M4*10 screws...

It holds all the tools that came with both the Ender 5 and the Ender 5 Plus, plus maybe a few others. ... The filament I use is Hatchbox, you can check them out here: https://amzn.to/38XzBLq If you're using something different, you might want to adjust...

An easy to print and simple cotton pad holder which snaps onto the frame of the Creality Ender 5 Plus. ...Useful for cleaning the glass bed with alcohol after each print. Print Settings Printer Brand: Creality Printer: Ender 5 Rafts: No Supports: No...

This upgraded version of the SpeedDrive v1 mounting bracket by sashalex007 eliminates geometry that interferes with the limit switch on the Ender 5 Plus. To convert an E5P to direct drive, all you need is a 400mm (16") stepper motor extension cable...

I used the 2020 frame clip-on of the “2020 Extrusion Webcam Mount [No Hardware] Logitech C270” found on thingiverse (https://www.thingiverse.com/thing:4636337) and the cable tree holder of the “Ender 5 / Ender 5 Plus Print Head Cable Strain Relief...

I'm Sick of Long Bowden Tubes and Backordered Hemeras, So I Designed a Direct Drive Mount for My Ender 5 Plus. I'd had it with the lengthy Bowden tube that always seemed to be in my way. Then, when I was ready to upgrade to a Hemera, it went out of...

I want to add the new Creality Sprite Extruder to my Ender 5 Plus. The Pro kit comes with a new mounting bracket for the 2020 gantry extrusion. However, the orientation of the belt for the X axis is 90 degrees off. Not wanting to go through an...

All parts are for the Creality Ender 5 Plus. The light strip can easily be stuck around the corners and you need less than 3 meters from the light stripes. Required parts: - 2 pieces AngleBar1 - 2 pieces AngleBar2 - 2 pieces...

My ender 5 plus factory spec out the box has this additional dampening bracket. Which needs slightly more space for the cover to fit properly. Test prints fit perfectly. Use the same fastening / fixtures listed in the original. ...Worked a treat.

# WHAT THIS 3D PRINT IS NEEDED FOR AND WHY IT WAS DEVELOPED: This 3D print resulted from the fact that after a while the cable guide of my Ender 5 plus kept bending towards the heatbed due to the weight. After a while, the cable guide was so deep...

This is a Cable Holder for the Ender 5 Plus with linear rails and the Micro Swiss Direct Drive I use this cable chains 20x10mm: https://www.aliexpress.com/item/32999589537.html?spm=a2g0s.9042311.0.0.27424c4dZDh4ri I use the cable chain trays from...

Snaps perfectly to the frame of the Ender Creality 5 Plus. The camera can be locked into place by rotating it onto the mount. Print orientation: Best printed on its side otherwise the print lines will be too weak and the snapfit part might...

Use the same information as the original file, this just adds a slot to store one additional SD card on the side From original: So I made this thing for my Ender 5 Plus +, you need a couple of M3 or M4 x 10 bolts and T-nuts to attach it. I also put a...

Ender 5 Plus bracket designed specifically for SKR 1.3 and 1.4 motherboards, optimized to provide easy access to the SD card slot and USB port. To assemble this bracket, you'll need to locate and carefully cut a precise slot and hole on one side of...

After purchasing Exoslides for my Ender 5 Plus I found that the H2 adapter wasn't compatible with the exoslide. Installing this requires disassembling the H2 to screw the center section of the extruder to the adapter. Next step is to connect the...

This is a remix of the switch mount for the 3DChameleon MK2 that fits in the rear left corner of the Ender 5 Plus sitting ontop of the corner bracket allowing for you to use the Y axis to trigger the switch. The switch ends up triggering at the same...

Mount for the Adafruit ADXL343 Accelerometer that works on a Ender 5 Plus with BLTouch. ... **Parts Required** - Adafruit ADXL343 [on Amazon](https://www.amazon.com/gp/product/B07PN6ZBJF/) - 2x M3*20mm Hex Socket Head Cap Screws and Nuts [on...

If you own an Ender 5 Plus and install the Printermods MDD 1.2 direct drive plate, you'll discover that the stock metal BLTouch mounting plate won't fit properly. None of the pre-printed BLTouch mounts match, so I chose to modify the metal one...

Using the BondTech BMG/V6/Volcano direct drive for Creality Printers by Hangtight on MyMiniFactory with the Ender 5 Plus can lead to a problem where the BLtouch doesn't trigger before the nozzle hits the bed. The BLtouch adapter screws in exactly...